1、ASD STANDARD NORME ASD ASD NORM prEN 3660-019 Edition P 1 September 2005 PUBLISHED BY THE AEROSPACE AND DEFENSE INDUSTRIES ASSOCIATION OF EUROPE - STANDARDIZATION Gulledelle 94 - B-1200 Brussels - Tel. + 32 2 775 8126 - Fax. + 32 2 775 8111 - www.asd-stan.orgICS: 49.060 Descriptors: Aeronautical ind
2、ustry, aircraft equipment, accessories, electrical connection equipment,electrical connector, characteristics, outlet, backshells ENGLISH VERSION Aerospace series Cable outlet accessories for circular and rectangular electrical and optical connectors Part 019: Cable outlet, style A, 45, unsealed, wi
3、th cable tie strain relief Product standard Srie arospatiale Accessoires arrires pour connecteurs circulaires et rectangulaires lectriques et optiques Partie 019 : Raccord coud, 45, non tanche, type A, avec tenue du cble par frettage Norme de produit Luft- und Raumfahrt Endgehuse fr elektrische und
4、optische Rund- und Rechtecksteckverbinder Teil 019: Endgehuse, Bauform A, 45, nicht abgedichtet, mit Arm fr Kabelbinder Produktnorm This “Aerospace Series“ Prestandard has been drawn up under the responsibility of ASD-STAN (The European Association of Aerospace Industries - Standardization). It is p
5、ublished for the needs of the European Aerospace Industry. It has been technically approved by the experts of the concerned Domain following member comments. Subsequent to the publication of this pre-standard, the technical content shall not be changed to an extent that interchangeability is affecte
6、d, physically or functionally, without re-identification of the standard. After examination and review by users and formal agreement of ASD-STAN, it will be submitted as a draft European Standard (prEN) to CEN (European Committee for Standardization) for formal vote and transformation to full Europe
7、an Standard (EN). The CEN national members have then to implement the EN at national level by giving the EN the status of a national standard and by withdrawing any national standards conflicting with the EN. Edition approved for publication 31 October 2005 Comments should be sent within six months
8、after the date of publication to ASD-STAN Electrical Domain Copyright 2005 by ASD-STAN prEN 3660-019:20052 Foreword This standard was reviewed by the Domain Technical Coordinator of ASD-STANs Electrical Domain. After inquiries and votes carried out in accordance with the rules of ASD-STAN defined in
9、 ASD-STANs General Process Manual, this standard has received approval for Publication. Contents Page 1 Scope . 3 2 Normative references 3 3 Terms and definitions . 3 4 Characteristics 3 5 Designation. 8 6 Marking 8 7 Technical specification 8 prEN 3660-019:20053 1 Scope This product standard define
10、s a range of cable outlets, style A, 45, straight, unsealed, with clamp strain relief. Associated electrical connector(s) : see EN 3660-002. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited
11、applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2424, Aerospace series Marking of aerospace products. EN 2591*, Aerospace series Elements of electrical and optical connection Test methods General. EN 3660-001, Aerospace series Cab
12、le outlet accessories for circular and rectangular electrical and optical connectors Part 001: Technical specification.1)EN 3660-002, Aerospace series Cable outlet accessories for circular and rectangular electrical and optical connectors Part 002: Index of product standards.1)3 Terms and definition
13、s For the purposes of this document, the terms and definitions given in EN 3660-001 apply. 4 Characteristics 4.1 Dimensions and mass For dimensions and mass, see Figure 1 and Table 1. Dimensions and tolerances are in millimetres. And all its parts quoted. 1) Published as AECMA Prestandard at the dat
14、e of publication of this standard. prEN 3660-019:2005A HC E 5,8 RefA B D GF 1Key 1 Cable tie or lace cord Figure 1 Detail A: see Figures 2a) to 2e). Figure 2a) Without ground lug and spacer pad Figure 2b) Without ground lug and with spacer pad Figure 2c) With ground lug and without spacer pad Figure
15、 2d) With ground lug and spacer pad Figure 2e) Spacer pad alone 6,66,8 3,63,34 prEN 3660-019:2005Table 1 A B CaD E F G H Without With Shell size Thread Without With Radius self-locking self-locking Mass max. Number of teeth Classes A, N & Wmax. 0,38 max. max. min. max. g g 09 M12x1-6H 19,60 24,80 6,
16、29 27,1 12,50 7,59 18,00 2,11 12 5,5 6,5 11 M15x1-6H 20,80 26,90 6,29 27,1 12,50 10,85 19,00 2,87 16 6,0 7,5 13 M18x1-6H 23,90 29,70 6,29 27,1 12,50 13,74 21,50 3,81 20 7,5 9,0 15 M21x1-6H 27,20 32,70 6,29 30,2 12,50 16,92 26,00 4,77 24 11,0 13,0 17 M25x1-6H 30,70 36,10 6,29 31,1 12,50 20,09 27,00 5
17、66 28 12,5 14,5 19 M28x1-6H 34,50 39,10 6,29 31,1 12,50 22,18 28,50 7,13 32 13,5 16,0 21 M31x1-6H 37,60 42,40 6,29 31,1 12,50 25,96 32,00 7,13 36 15,0 18,5 23 M34x1-6H 40,60 51,10 6,29 31,1 12,50 29,13 34,50 7,82 40 17,5 20,5 25 M37x1-6H 43,20 53,80 6,29 31,1 12,50 32,31 36,50 8,89 44 20,5 25,0 a“C
18、 dimensions is taken when the coupling nut is pulled in forward position. 4.2 Interface dimensions See Figure 3 and Table 2. 0,790 0,2 (1002) R 0,50 0,13 R 0,25 0,13 C B AD Figure 3 5 prEN 3660-019:20056 Table 2 A B C D 0 0,15 max. min. min. Shell size mm mm mm mm N Number of teeth 09 10,57 7,50 6,
19、70 2,90 12 11 13,56 10,80 9,90 2,90 16 13 16,58 13,80 12,80 2,90 20 15 20,57 16,90 16,00 2,90 24 17 23,57 20,10 19,20 2,90 28 19 25,57 22,80 21,40 2,90 32 21 29,97 26,00 24,60 2,90 36 23 32,56 29,10 27,70 2,90 40 25 35,56 32,30 30,90 1,70 44 4.3 Material and finish Backshell: Class A : Aluminium all
20、oy/Black anodise plating Class N : Aluminium alloy/Nickel plate Class W : Aluminium alloy/Olive Drab cadmium plate Spacer pad: silicone 4.4 Assembly torque These torque values are intended for installation use only. See Table 3. Table 3 Shell size Torque Nm 0,5 09 7,80 11 10,60 13 15,20 15 16,30 17
21、16,30 19 16,30 21 19,10 23 19,10 25 19,10 prEN 3660-019:20057 4.5 Tests Test details to be in accordance with Table 4 and EN 3660-001. Table 4 EN 2591- Test No. Title Not applicable Applicable see EN 3660-001 Particulars 101 Visual examination X 102 Examination of dimensions and mass X See 4.1. 205
22、Housing (shell) electrical continuity X 212 Surface transfer impedance (from 100 MHz to 1 GHz) aX 301 Endurance at temperature X According to class 305 Rapid change of temperature X 306 Mould growth X See EN 3660-001, 10.2.3. 307 Salt mist X Cable outlet not fitted to a connector and suspended with
23、non metallic cord. Duration: Classes A & N 48 h Classes W & K 500 h 308 Sand and dust X 314 Immersion at low air pressure X 315 Fluid resistance X 316 Ozone resistance X 317 Flammability X With spacer pad 318 Fire-resistance X 402 Shock X Method A. Severity: 100 g 403 Sinusoidal and random vibration
24、 X Method B. Figure 3. Level J Duration: 8 h in each of two axes. Test performed: on one group 50 % of time at 65 C 50 % of time at ambient temperature on a second group 100 % of time at maximum temperature of class under test 406 Mechanical endurance X 408 Mating and unmating forces X 420 Mechanica
25、l strength of rear accessories X Phase D and Table 5 422 Locking wire hole strength X 513 Residual magnetism X Not fitted to a connector. Max values Classes A, N & W 2,0 Class K 5,0 a1 GHz to 10 GHz under consideration. prEN 3660-019:20055 Designation EXAMPLE 1 Description block CABLE OUTLET Identit
26、y block EN3660-019XXXXX 8 Number of this standard Material/Finish class (see 4.3) Coupling nut 1 without self-locking device 2 with self locking device Strain relief type A without spacer pad and ground lug B with spacer pad and ground lug C with spacer pad and without ground lug D without spacer pa
27、d and with ground lug Shell size EXAMPLE 2 EN3660-019A1A09 Style A cable outlet, aluminium, black anodized plating, without self-locking, without spacer pad and ground lug, shell size 09. NOTE 1 No gaps are required between sections in the part number when printed. NOTE 2 If necessary, the code I9005 may be placed between the description block and the identity block. 6 Marking According to EN 2424 category P. 7 Technical specification Refer to EN 3660-001.
