1、ASD-STAN STANDARD NORME ASD-STAN ASD-STAN NORM prEN 4701-001 Edition P 2 March 2013 PUBLISHED BY THE AEROSPACE AND DEFENCE INDUSTRIES ASSOCIATION OF EUROPE - STANDARDIZATIONRue Montoyer 10 - 1000 Brussels - Tel. 32 2 775 8126 - Fax. 32 2 775 8131 - www.asd-stan.orgICS: Supersedes edition P 1 of Dece
2、mber 2010 and will supersede EN 4701-001:2013Descriptors: ENGLISH VERSION Aerospace series Connectors, optical, rectangular, modular, operating temperature 125 C, for EN 4531-101 contacts Part 001: Technical specification Srie arospatiale Connecteurs optiques rectangulaires, modulaires, temprature d
3、utilisation 125 C, pour contacts EN 4531-101 Partie 001 : Spcification technique Luft- und Raumfahrt Optischer Rechtecksteckverbinder in modularer Bauweise Betriebstemperatur 125 C, fr EN 4531-101 Kontakte Teil 001: Technische Lieferbedingungen This “Aerospace Series“ Prestandard has been drawn up u
4、nder the responsibility of ASD-STAN (The AeroSpace and Defence Industries Association of Europe - Standardization). It is published for the needs of the European Aerospace Industry. It has been technically approved by the experts of the concerned Domain following member comments. Subsequent to the p
5、ublication of this Prestandard, the technical content shall not be changed to an extent that interchangeability is affected, physically or functionally, without re-identification of the standard. After examination and review by users and formal agreement of ASD-STAN, it will be submitted as a draft
6、European Standard (prEN) to CEN (European Committee for Standardization) for formal vote and transformation to full European Standard (EN). The CEN national members have then to implement the EN at national level by giving the EN the status of a national standard and by withdrawing any national stan
7、dards conflicting with the EN. Edition approved for publication 31 March 2013 Comments should be sent within six months after the date of publication to ASD-STAN Electrical Domain Copyright 2013 by ASD-STAN prEN 4701-001:2013 (E) 2 Contents Page Foreword 2 Introduction .3 1 Scope 4 2 Normative refer
8、ences 4 3 Terms and definitions .4 4 Description .5 5 Design .6 6 Definition drawings8 7 Tests 15 8 Quality assurance 19 9 Designation and marking 26 Foreword This standard was reviewed by the Domain Technical Coordinator of ASD-STANs Electrical Domain. After inquiries and votes carried out in accor
9、dance with the rules of ASD-STAN defined in ASD-STANs General Process Manual, this standard has received approval for Publication. prEN 4701-001:2013 (E) 3 Introduction This family of fibre optic connectors is derived from EN 4165-001 with EN 4531-101 optical contacts. It is suitable for use on aero
10、space on board applications. It provides easy access for optical contact end face cleaning. prEN 4701-001:2013 (E) 4 1 Scope This standard specifies the general characteristics, the conditions for qualification, acceptance and quality assurance, as well as the test programs and groups for EN 4165 re
11、ctangular connectors with removable optical modules using EN 4531-101 contacts. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the re
12、ferenced document (including any amendments) applies. EN 2591 (all parts), Aerospace series Elements of electrical and optical connection Test methods EN 3909, Aerospace series Test fluids for electric components and sub-assemblies EN 4531 (all parts), Aerospace series Connectors, optical, circular,
13、 single and multipin, coupled by threaded ring Flush contacts EN 4165 (all parts), Aerospace series Connectors, electrical, rectangular, modular Operating temperature 175 C continuous EN 4701-002, Aerospace series Connectors, optical, rectangular, modular, operating temperature 125 C, for EN 4531-10
14、1 contacts Part 002: Specification of performance 1)EN 4701-003, Aerospace series Connectors, optical, rectangular, modular, operating temperature 125 C, for EN 4531-101 contacts Part 003: Module series 2 Product standard 1)EN 9133, Aerospace series Quality management systems Qualification procedure
15、 for aerospace standard parts MIL-I-81969/14-04, Installing and removal tools, connector electrical contact, type III, class 2, composition B2)TR 4684, Aerospace series Electrical and Optical technology and component definitions 3)3 Terms and definitions For the purposes of this document, the terms
16、and definitions given in TR 4684 apply. 1) Published as ASD-STAN Prestandard at the date of publication of this standard. http:/www.asd-stan.org/ 2) Published by; DoD National (US) Mil. Department of Defense. http:/www.defenselink.mil/ 3) In preparation at the date of publication of this standard. p
17、rEN 4701-001:2013 (E) 5 4 Description 4.1 General This document describes an optical connector module to be installed in plug and receptacle housings. Plug and receptacle housings conform to EN 4165-001. The connectors use rear removable optical contacts with a ferrule diameter of 2,5 mm in accordan
18、ce with EN 4531-101. The precise alignment of the optical contacts is accomplished by a central alignment pin/socket and alignment sleeves. The receptacles and plugs contain either male or female module. The male module is characterised by alignment pin. The inserts can be installed and removed from
19、 the shell by mean of a tool as specified EN 4165-022. Keying system conform to EN 4165-001. Connector type designation as specified in EN 4165-001. Not compatible with back shells and cable clamp defined in EN 4165-002. 4.2 Receptacle Receptacle description as specified in EN 4165-001. 4.3 Plug Plu
20、g description as specified in EN 4165-001. 4.4 Module Mechanical interface and polarization between housings and modules conform to EN 4165-001. The module assembly shall be single-bloc type design complete with a keyed contact retention system and appropriate seals. The male and female modules use
21、hermaphroditic contacts as specified in EN 4531-101. 4.5 Materials and surface treatment 4.5.1 General See EN 4165-001. 4.5.2 Housings The connector housing description is specified in EN 4165-001. prEN 4701-001:2013 (E) 6 4.5.3 Optical contacts and alignment sleeves The contacts shall be of suitabl
22、e materials as specified in the product standard EN 4531. The optical alignment sleeves shall be of suitable materials as specified in the product standard EN 4701-002. The optical contacts are spring-loaded. The spring force is defined in the product standard EN 4531. 4.5.4 Metallic or non-metallic
23、 materials The materials used for modules, seals and grommets shall have a hardness and mechanical characteristics consistent with the required use. 5 Design 5.1 Housing The connector housing design is specified in EN 4165-001. 5.2 Modules The modules carrying the optical contacts shall be in hard m
24、aterial and have a cross section and radii such that no cracks, flaking or breaks can occur in normal operation. The module is mechanically held in the connector housing by retention clips, and removable with the use of an extraction tool. The mechanical contacts retention system shall be integrated
25、 in the hard module. The front face of the module shall be such that sealing is ensured when the connectors are coupled. The interfacial seal shall be permanently fastened on the male module. Sealing of the rear face of the module is provided by the contact boot. The design shall permit individual i
26、nstallation of the contacts without removal of the module. Insertion and removal of the contacts shall be from the rear. For ease of operation, tools as per MIL-I-81969/14-04 standard (P/N for size 12) may be used. Contact identification shall be permanent and contrasted on the rear face of the inse
27、rt. prEN 4701-001:2013 (E) 7 5.3 Connector mating sequence 5.3.1 Centre coupling mechanism The mating sequence shall be: face to face positioning; keyways polarization guide; plug receptacle shell; central thread coupling; alignment pin engagement; contact alignment; optical physical contact; sealed
28、 interface compression; metal/metal or composite shell to shell bottoming. 5.3.2 Push-pull latching mechanism The connector mating sequence should be as follows: face to face positioning; plug receptacle shell; keyways polarization guide; alignment pin engagement; contact alignment; optical physical
29、 contact; locking mechanism alignment; sealed interface compression maintaining; locking mechanism engagement. 5.4 Connector mating Housing design shall prevent incorrect mating of the plug onto receptacle. prEN 4701-001:2013 (E) 8 6 Definition drawings 6.1 General The general dimensions and the mas
30、ses of receptacles, plugs and protective covers are given in the product standards. 6.2 Receptacle All housing dimensions are defined in EN 4165-001. 6.3 Plug All housing dimensions are defined in EN 4165-001. 6.4 Modules 6.4.1 General All dimensions are defined in EN 4701-003. prEN 4701-001:2013 (E
31、) 9 6.4.2 Plug and receptacle, series 2 Insert and contact position. See Figure 1. Dimensions and tolerances in millimetres. A NOTE Others dimensions are in accordance with EN 4165 standards. Figure 1 prEN 4701-001:2013 (E) 10 6.4.3 Plug and receptacle single module Insert and contact position. See
32、Figure 2. Dimensions and tolerances in millimetres. aGuinding pin NOTE Others dimensions are in accordance with EN 4165 standards. Figure 2 prEN 4701-001:2013 (E) 11 6.5 Mating dimensions 6.5.1 Plug, series 2, contact bayonet position See Figure 3 for plug with female module and Figure 4 for plug wi
33、th male module. Dimensions are in millimetres. aWhen sleeve is in rear position. Figure 3 Figure 4 6.5.2 Receptacle, series 2, contact bayonet position See Figure 5 for receptacle with male module and Figure 6 for receptacle with female module. Dimensions in millimetres. aWhen sleeve is in rear posi
34、tion. Figure 5 Figure 6 prEN 4701-001:2013 (E) 12 6.5.3 Plug, single module, contact bayonet position See Figure 7 for plug with male module and Figure 8 for plug with female module. Dimensions in millimetres. aWhen sleeve is in rear position. Figure 7 Figure 8 6.5.4 Receptacle, single module, conta
35、ct bayonet position See Figure 9 for receptacle with male module and Figure 10 for receptacle with female module. Dimensions in millimetres. aWhen sleeve is in rear position. Figure 9 Figure 10 prEN 4701-001:2013 (E) 13 6.5.5 Coupling contact position See Figure 11. Condition: In every case, J 0 The
36、 different shapes and dimensions of the sleeve cavity must be defined to warranty this condition Key 1 Optical contact to sleeve holder stop 2 Sleeve to sleeve holder cavity stop Figure 11 prEN 4701-001:2013 (E) 14 6.5.6 Contact arrangements Contact arrangements: See Figure 12. Y mm X mm 3 0 3 Coord
37、inate positions of contacts 2,75 1 2 0 Guide 2,75 3 4 Figure 12 prEN 4701-001:2013 (E) 15 7 Tests 7.1 Tests according to EN 2591-100 The tests of EN 2591, applicable in the context of this standard as well as the details necessary for implementing them and for inspecting connector characteristics, a
38、re given in Table 1. Table 1 (1 of 5) EN 2591- Designation of the test Details 6101 Optical elements Visual examination End-face optical examination at 200 magnification minimum. At the beginning of life: optical face undamaged and free from contamination, After tests: no cracks, excessive scratches
39、 and detached parts, After tests: pictures of permanent defects shall be recorded. 102 Examination of dimensions and mass According to Clause 6 and product standard. The checking of inaccessible dimensions on the finished product shall be carried out on part pieces or given by the quality organizati
40、on of the manufacturer concerned. 6301 Optical elements Endurance at temperature For performance and test method requirements refer to the applicable product standard for the component and cable under test. 6303 Optical elements Cold/low pressure and damp heat Duration: 5 (five) cycles Minimum tempe
41、rature: ( 65 2) C Measurement during test: at each transition point. 306 Mould growth Method A 6305 Optical elements Rapid change of temperature For performance and test method requirements refer to the applicable product standard for the component and cable under test. 6307 Optical elements Salt mi
42、st Connectors should be submitted to 50 cycles of mating/ unmating at a rate which shall not exceed 5 (five) cycles per minute. Samples shall be placed in salt mist chamber during 452 h in mated position; Then insertion loss measurement; 48 h in unmated position. 308 Sand and dust Connector mated an
43、d positioned such that rear of free plug faces into the wind direction. Wind velocity in duct: (3,5 0,5) m/s. Number of cycles: 1 (one) 309 Dry heat Not applicable. prEN 4701-001:2013 (E) 16 Table 1 (2 of 5) EN 2591- Designation of the test Details 310 Cold Not applicable. 311 Low air pressure Not a
44、pplicable. 312 Air leakage Method A Differential pressure: 40 kPa during two hours Maximum leakage flow: 16 cm3/h/module 313 Driving rain (artificial) Not applicable. 6314 Optical elements Immersion at low air pressure Applicable at 2 kPa 6315 Optical elements Fluid resistance See Table 2 for fluids
45、, number of cycles, temperature and time of immersion, and temperature of third phase. 6316 Optical elements Ozone resistance Not applicable. 6317 Optical elements Flammability Method A 6318 Optical elements Fire resistance Not applicable. 319 Gastightness of solderless wrapped connections Not appli
46、cable. 320 Simulated solar radiation at ground level Not applicable. 6321 Optical elements Damp heat, cyclic test Connector mated, 10 cycles 6323 Optical elements Thermal shock (hermetically sealed devices) Not applicable. 6324 Optical elements Interfacial sealing Not applicable. 325 Ice resistance
47、Not applicable. 6401 Optical elements Acceleration steady state Not applicable. 6402 Optical elements Shock Method A, severity 100 Number of shocks: One each way for each of the three directions (six shocks in all). 6403 Optical elements Vibrations Connector mated Method A: Figure 1, 20 gn, one octa
48、ve per minute Duration: 4 (four) h/axis Method B: Figure 2, Table 1, level E Duration: 1 (one) h/axis 6404 Optical elements Transverse load For performance and test method requirements refer to the applicable product standard for the component and cable under test. prEN 4701-001:2013 (E) 17 Table 1
49、(3 of 5) EN 2591- Designation of the test Details 6405 Optical elements Axial load For performance and test method requirements refer to the applicable product standard for the component and cable under test. 6406 Optical elements Mechanical endurance Number of mating and unmating operations: 500 The rate shall not exceed 5 (five) cycles/min Optical faces must be cleaned every 20 cycles. 407 Durability of contact retention system
