1、ASD-STAN STANDARD NORME ASD-STAN ASD-STAN NORM ASD-STAN prEN 6059-402 Edition P 2 July 2017 PUBLISHED BY THE AEROSPACE AND DEFENCE INDUSTRIES ASSOCIATION OF EUROPE - STANDARDIZATION Rue Montoyer 10 - 1000 Brussels - Tel. 32 2 775 8126 - Fax. 32 2 775 8131 - www.asd-stan.org ICS: Supersedes edition P
2、 1 of September 1997 Descriptors: ENGLISH VERSION Aerospace series Electrical cables, installation Protection sleeves Test methods Part 402: Bending properties Luft- und Raumfahrt Elektrische Leitungen, installation Schutzschluche Prfverfahren Teil 402: Biegeeigenschaften Srie arospatiale Cbles lect
3、riques, installation Gaines de protection Mthodes dessais Partie 402 : Aptitude la flexion This “Aerospace Series“ Prestandard has been drawn up under the responsibility of ASD-STAN (The AeroSpace and Defence Industries Association of Europe - Standardization). It is published for the needs of the E
4、uropean Aerospace Industry. It has been technically approved by the experts of the concerned Domain following member comments. Subsequent to the publication of this Prestandard, the technical content shall not be changed to an extent that interchangeability is affected, physically or functionally, w
5、ithout re-identification of the standard. After examination and review by users and formal agreement of ASD-STAN, the ASD-STAN prEN will be submitted as a draft European Standard (prEN) to CEN (European Committee for Standardization) for formal vote and transformation to full European Standard (EN).
6、 The CEN national members have then to implement the EN at national level by giving the EN the status of a national standard and by withdrawing any national standards conflicting with the EN. ASD-STAN Technical Committee approves that: “This document is published by ASD-STAN for the needs of the Eur
7、opean Aerospace Industry. The use of this standard is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefrom, is the sole responsibility of the user.” ASD-STAN reviews each standard and technical report at least every fiv
8、e years at which time it may be revised, reaffirmed, stabilized or cancelled. ASD-STAN invites you to send your written comments or any suggestions that may arise. All rights reserved. No parts of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any
9、means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of ASD-STAN. Order details: E-mail: salesasd-stan.org Web address: http:/www.asd-stan.org/ Edition approved for publication 1st July 2017 Comments should be sent within six months after the date of
10、 publication to ASD-STAN Electrical Domain Copyright 2017 ASD-STAN prEN 6059-402:2017 (E) 2 Contents Page Foreword 2 1 Scope 3 2 Normative references 3 3 Preparation of specimens 3 4 Apparatus. 4 5 Method 5 6 Requirements . 5 Foreword This standard was reviewed by the Domain Technical Coordinator of
11、 ASD-STANs Electrical Domain. After inquiries and votes carried out in accordance with the rules of ASD-STAN defined in ASD-STANs General Process Manual, this standard has received approval for Publication. prEN 6059-402:2017 (E) 3 1 Scope This standard specifies a method to determine the bending pr
12、operties of protection sleeve for electrical cable and cable bundles. It shall be used together with EN 6059-100. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the
13、 edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 6059-100, Aerospace series Electrical cables, installation Protection sleeves Test methods Part 100: General 3 Preparation of specimens A specimen with a minimum lengt
14、h of 600 mm is taken from a finished sleeve. prEN 6059-402:2017 (E) 4 4 Apparatus A spiral wrapped bending spring which has the nominal inner diameter of the specimen to be tested and capable of bending with a minimum radius (radius is specified as five times the nominal inner diameter, measured to
15、the centerline of the spring) as specified in the product standard. The sleeve shall be applied between two mandrels to bend the sleeve to both sides at the minimum specified bend radius. The sleeve shall be bent by means of a lever with a rotation point just above the mandrels, see Figure 1. The ap
16、plied mass shall be in accordance with the product standard. A counter to measure the cycles with an interface between lever and counter. Key A Axis of rotation for flex arm F Flex arm M Mandrel G Guidance rod W Weight attached to cables A-A Section along the line A-A B-B Section along the line B-B
17、Figure 1 Test set-up for bending properties of sleeves prEN 6059-402:2017 (E) 5 5 Method The specimen should be bent 90 to left and 90 to right. The sleeve shall be applied between the two mandrels according to Figure 1. The number of cycles is specified in the product standard. The movement bent 90
18、 to left and 90 to right is one cycle. The axis of rotation for flex arm shall be at the same level or above the axis mandrels. Guide rods and weight loaded on conductors can be used so as to avoid movement not relevant for this test. For bundles whose diameter is larger than 32 mm, the use of convo
19、luted conduit to reduce the weight of harness during the test cables shall be used so as to prevent contact between the convoluted conduit and the sleeve. See Figure 2. Key A Protection sleeve B Cables arranged around conduit C Convoluted conduit Figure 2 Cable bundle with convoluted tube 6 Requirements The specimen shall be capable of bending to the minimum bend radius as specified in the product standard. Closing mechanisms (if present) shall not be opened or damaged. No damage or broken yams/strand shall be found after the test.
