1、Designation: C1264 14C1264 14aStandard Specification forSampling, Inspection, Rejection, Certification, Packaging,Marking, Shipping, Handling, and Storage of Gypsum PanelProducts1This standard is issued under the fixed designation C1264; the number immediately following the designation indicates the
2、 year oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope Scope*1.1 This specification covers sampling; inspecti
3、on; rejection; certification; packaging and marking; and shipping, handling, andstorage of gypsum panel products shipped from the manufacturer to distributors, dealers, retailers or other resellers.manufacturer.1.1.1 This specification does not cover storage or stocking on individual job sites.1.2 T
4、his standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibilityof the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatorylimitations prior to use.2. Referenced Document
5、s2.1 ASTM Standards:2C11 Terminology Relating to Gypsum and Related Building Materials and SystemsC1396/C1396M Specification for Gypsum Board2.2 ISO Standards:3ISO 31661 Codes for the representationRepresentation of namesNames of countries and their subdivisions - Part Countries andTheir Subdivision
6、sPart 1: Country codesCodes3. Terminology3.1 DefinitionsDefinitions shall be in accordance with Terminology C11.4. Sampling4.1 When specified by the purchase agreement, samples of gypsum panel products shall be taken at the place of manufactureor at the destination. If the samples are taken at the d
7、estination, such samples shall be taken within 24 h of the receipt of thematerial.4.2 At least 0.25 % of the number of gypsum panel products in a shipment, but not less than three gypsum panel products, shallbe so selected as to be representative of the shipment and shall constitute a sample for the
8、 purpose of tests by the purchaser or user.5. Inspection5.1 Inspection of the gypsum panel products shall be agreed upon between the purchaser and the producer or supplier as partof the purchase agreement.6. Rejection6.1 Rejection of gypsum panel products that fails to conform to the requirements of
9、 the specification shall be reported to theproducer or supplier promptly and in writing. The notice of rejection shall contain a statement documenting how the gypsum panelproducts hashave failed to conform to the requirements of the specification.1 This specification is under the jurisdiction of AST
10、M Committee C11 on Gypsum and Related Building Materials and Systems and is the direct responsibility ofSubcommittee C11.01 on Specifications and Test Methods for Gypsum Products.Current edition approved April 15, 2014Sept. 1, 2014. Published June 2014October 2014. Originally approved in 1994. Last
11、previous edition approved in 20112014 asC1264 11.C1264 14. DOI: 10.1520/C1264-14.10.1520/C1264-14A.2 For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at serviceastm.org. For Annual Book of ASTM Standardsvolume information, refer to the standards Docu
12、ment Summary page on the ASTM website.3 Available from International Organization for Standardization (ISO), 1, ch. de la Voie-Creuse, CP 56, CH-1211 Geneva 20, Switzerland, http:/www.iso.org.This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indica
13、tion of what changes have been made to the previous version. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be con
14、sidered the official document.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States17. Certification7.1 When specified in the purchase agreement, a producers or suppliers repo
15、rt shall be furnished at the time of shipmentcertifying that the product is in compliance with the ASTM specification referencing this specification.8. Packaging and Marking8.1 Each gypsum panel product or package shall have legibly marked thereon the following: the thickness, the name of theproduce
16、r or supplier, the brand name, if any, and the ASTM specification for the product.8.2 In addition to the marking described in 8.1, gypsum board manufactured to Specification C1396/C1396M shall be markedas described in Annex A1.8.3 Single, unbound panels of gypsum board manufactured to Specification
17、C1396/C1396M that are packaged in multi-panelunits shall be permitted to be marked as a palletized packaging unit. These units are typically packaged to meet specific contractualrequirements and as such the marking requirements of 8.1 and 8.2 are not applicable.9. Shipping, Handling, and Storage9.1
18、Gypsum panel products shall be shipped so as to be kept dry.9.2 Gypsum panel products shall be stored so as to be kept dry, preferably inside a building. Gypsum panel products shall beneatly stacked flat with care taken to prevent sagging or damage to edges, ends, and surfaces.9.3 Where necessary to
19、 store gypsum panel products outside, it shall be stacked flat, off the ground, supported on a levelplatform, and fully protected from weather and direct sunlight exposure.C1264 14a210. Keywords10.1 certification; gypsum; gypsum panel products; handling; inspection; marking; packaging; rejection; sa
20、mpling; shipping;storageANNEXA1. Marking RequirementsA1.1 Each individual sheet of gypsum board manufactured to Specification C1396/C1396M shall have the following informationlegibly printed on the back surface:A1.1.1 The name of the manufacturing company or a unique alpha code of not less than thre
21、e letters identifying the manufacturerof the gypsum board.A1.1.2 A unique alpha or numeric code identifying the manufacturing facility and the production line.A1.1.3 A code identifying the date and time of manufacture.A1.1.4 The three-letter alpha code as designated in ISO 3166-1 identifying the cou
22、ntry of manufacture.A1.2 The printed information described in A1.1 shall be:A1.2.1 One or more lines oriented in the machine direction, parallel to one edge of the sheet.A1.2.2 Reproduced in its entirety at an interval of not more than 6 ft (1800 mm) on center.A1.2.3 Placed not less than 1 in. (25 m
23、m) 1 in. (25 mm) nor more than 15 in. (380 mm) 15 in. (380 mm) from the edge of thesheet.SUMMARY OF CHANGESCommittee C11 has identified the location of selected changes to this classification since the last issue,C1264 14, that may impact the use of this classification. (Approved Sept. 1, 2014.)(1)
24、Revised 1.1.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such
25、 rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn.Your comments are invited either for revision of this standard or for additio
26、nal standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the A
27、STM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the ab
28、oveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 14a3
