1、Designation: D1072 06 (Reapproved 2017)Standard Test Method forTotal Sulfur in Fuel Gases by Combustion and BariumChloride Titration1This standard is issued under the fixed designation D1072; the number immediately following the designation indicates the year oforiginal adoption or, in the case of r
2、evision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method is for the determination of total sulfurin combustible fuel gases, when present
3、in sulfur concentra-tions between approximately 25 and 700 mg/m3(1 to 30 grainsper 100 cubic feet). It is applicable to natural gases, manufac-tured gases, mixed gases, and other miscellaneous gaseousfuels.1.2 The values stated in inch-pound units are to be regardedas standard.1.3 This standard does
4、 not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety, health, environmental practices and determinethe applicability of regulatory limitations prior to use.1.4 This international stan
5、dard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade (TBT) Committee.2. R
6、eferenced Documents2.1 ASTM Standards:2D1193 Specification for Reagent Water3. Summary of Test Method3.1 A metered sample of gas is burned in a closed system inan atmosphere of sulfur-free air. The oxides of sulfur producedare absorbed in sodium carbonate solution, where they areoxidized to sulfate.
7、 The sulfate in the absorbent solution isdetermined by titration with standardized barium chloridesolution, using tetra-hydroxy-quinone (THQ) as an indicator.4. Interferences4.1 There are no known interferences for the determinationof total sulfur in fuel gases when combustion is followed bybarium c
8、hloride titration. However, users employing bariumchloride titration following collection of sulfur dioxide byalternative procedures are cautioned that ammonia, amines,substances producing water soluble cations, and fluorides willinterfere with the titration.5. Apparatus5.1 Burner (Fig. 1), as speci
9、fied in the Appendix X1.5.2 Chimneys, Absorbers and Spray Traps, (Fig. 2), asspecified in the Appendix X1.5.3 Flow meterA calibrated capillary flow meter forpredetermining and indicating the rate of flow of gas to theburner. The capillary selected should be of such size that at therequired rate of f
10、low the differential pressure is at least 20 cmof water. A scale divided into millimeters will then provide areading precision of 6 0.5 %. Other metering devices, includ-ing but not limited to rotameters or dry displacement meters,are suitable provided the reading precision is 6 0.5 % or better.A fl
11、ow controlling valve is attached to the inlet connection ofthe flow meter.5.4 Vacuum SystemA vacuum manifold equipped with avacuum regulating device, valves, and other necessary accou-terments. An example vacuum system capable of performingmultiple test measurements is shown in Fig. 3. Other vacuums
12、ystem configurations can be used to perform this test method.The vacuum system shall be connected to a vacuum pumpcapable of providing a steady gas flow of 3 L of air per minutethrough each absorber and capable of maintaining a constantmanifold pressure of approximately 40 cm of water belowatmospher
13、ic pressure.5.5 Air-Purifying SystemA device supplying purified airto the burner manifold at a constant pressure of approximately200 mm of water and to the chimney manifold at a pressure of1 to 2 cm of water. An example system configuration formultiple tests is illustrated in Fig. 4; however, other
14、air-purifying system configurations can be used to perform this testmethod. The tubing that connects the chimneys to the manifold1This test method is under the jurisdiction ofASTM Committee D03 on GaseousFuels and is the direct responsibility of D03.05 on Determination of SpecialConstituents of Gase
15、ous Fuels.Current edition approved Nov. 1, 2017. Published December 2017. Originallyapproved in 1954. Last previous edition approved in 2012 as D1072 06(2012).DOI: 10.1520/D1072-06R17.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm
16、.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with int
17、ernationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.1shall be of an internal diameter not smaller t
18、han 0.63 cm inorder to prevent unnecessary restriction of airflow.5.6 ManometerA water manometer for indicating the gaspressure at the point of volume measurement. It is connectedbetween the flowmeter and the burner, with one leg open to theatmosphere.6. Reagents and Materials6.1 Reagents PurityReag
19、ent grade chemicals shall beused in all tests. Unless otherwise indicated, it is intended thatall reagents shall conform to the specifications of the Commit-tee on Analytical Reagents of the American Chemical Society,where such specifications are available.3Other grades may beused, provided it is fi
20、rst ascertained that the reagent is ofsufficiently high purity to permit its use without adverselyimpacting the accuracy of the determination. WarningSodium hydroxide is corrosive and can cause severe damage toeyes and skin. Inhalation will irritate the nose, throat and lungs.It reacts exothermicall
21、y with water.6.2 Purity of WaterUnless otherwise indicated, referencesto water shall be understood to mean reagent water conformingto Specification D1193.6.3 AlcoholEthyl alcohol, denatured by Formula 30 or3-A, or isopropyl alcohol.6.4 Barium Chloride,(CAS No: 10361-37-2), Standard So-lution (1 mL =
22、 1 mg S)Dissolve 7.634 g of barium chloride(BaCl22H2O) in water and dilute to 1 L. The solution isstandardized gravimetrically by precipitation as barium sulfateor by titration against sulfuric acid (see 6.12)6.5 Hydrochloric Acid (CAS No 7647-01-0) (2.275-g HCl/L)Titrated against Na2CO3solution (se
23、e 6.15), using methylorange indicator. Adjusted such that 1 mL of HCl solution isequivalent to 1 mL of Na2CO3solution.6.6 Hydrogen Peroxide (30 %)(H2O2;CAS No: 7722-84-1).6.7 iso-Propanol (CAS No. 67630)6.8 Potassium Hydrogen Phthalate (KHP; CAS No 877-24-7) Dry use.6.9 Phenolphthalein (CAS No 77-09
24、-8)6.10 Methyl Orange (CAS No 547-58-0) IndicatorSolutionDissolve 0.1 g of methyl orange in 100 mL of water.6.11 Silver Nitrate (CAS No 7761-88-8)Solution (17-gAgNO3/L)Dissolve 1.7 g of silver nitrate (AgNO3)in100mL of water. Store in a brown bottle.6.12 Sodium Carbonate (CAS No 5968-11-6) Solution(
25、3.306-g Na2CO3/L)Dissolve 3.306 g of sodium carbonate(Na2CO3) in water and dilute to 1 L.6.13 Sodium Hydroxide Solution (CAS No 1310-73-2)(100-g NaOH/L)Dissolve 100 g of technical grade sodiumhydroxide (NaOH) pellets in water and dilute to 1 L. Standard-ize against potassium hydrogen phthalate (See
26、6.1)6.14 Sulfuric Acid(CAS No 7664-93-9) (1+16)Mix 60mL of concentrated sulfuric acid (H2SO4, sp gr 1.84) with 960mL of water.6.15 Tetrahydroxyquinone Indicator (THQ CAS No. 5676-48-2), in powdered form.6.16 Thorin indicator (CAS No. 132-33-2)7. Calibration and Standardization7.1 Sodium Hydroxide So
27、lution Standardization The fol-lowing provides an example procedure for standardization;other quantities of reagents, as convenient, can be used. Dryand crushed potassium hydrogen phthalate (KHP) is heated inan oven at 105 C for 2 hours and allowed to cool to roomtemperature in a desiccator. KHP (95
28、0 6 50 mg weighed to thenearest 0.1 mg) is placed in an Erlenmeyer flask. Water (70mL) and 2-4 drops of phenolphthalein are added. Titrate theKHP solution with the sodium hydroxide solution preparedunder 6.13 to a faint pink color. Repeat the titration using asecond portion of KHP. Titrate a 70 mL w
29、ater blank containing1-4 drops of phenolphthalein to a faint pink color using thesodium hydroxide solution prepared under 6.13. Repeat thisprocedure and average the results. For both the water blank andthe KHPtitration replicates should agree to 0.05 mLtitrant. Foreach KHP trial, independently calcu
30、late the normality for thesodium hydroxide solution according to the following equa-tion:Normality of NaOH 5mg KHP/204.23 mL NaOH 2 avg. mL blank!(1)Values for the two KHP trials should agree within 6 0.5percent. If they do not, repeat the titrations or identify thecause for the excessive discrepanc
31、y, or both.7.2 Sulfuric Acid Standardization The following providesan example procedure for standardization; other quantities ofreagents, as convenient, can be used. Titrate the sulfuric acidsolution prepared under 6.14 against the sodium hydroxidestandardized in 7.1 using 2-4 drops of phenolphthale
32、in as theindicator. Repeat and average the result for the normality of thesulfuric acid. Values for the two trials should agree within 63Reagent Chemicals, American Chemical Society Specifications, AmericanChemical Society, Washington, DC. For suggestions on the testing of reagents notlisted by the
33、American Chemical Society, see Analar Standards for LaboratoryChemicals, BDH Ltd., Poole, Dorset, U.K., and the United States Pharmacopeiaand National Formulary, U.S. Pharmacopeial Convention, Inc. (USPC), Rockville,MD.NOTE 1All dimensions in millimetres.FIG. 1 Gas Burner for Sulfur DeterminationD10
34、72 06 (2017)20.5 percent. If they do not, repeat the titrations or identify thecause for the excessive discrepancy, or both.7.3 Barium Chloride Solution Standardization Titratethe barium chloride solution against the previously standard-ized sulfuric acid solution (see 7.2). This can be conveniently
35、accomplished by transferring 10.0 mL sulfuric acid to a flaskwhere 40 mL iso-propanol and 2-4 drops thorin indicator areadded. This is titrated to a pink end point using the bariumchloride solution. Repeat the titration and average the results.The replicate titrations should agree within 0.5 percent
36、. If theydo not, repeat the titrations or identify the cause for theexcessive discrepancy, or both. Using this same procedure,perform duplicate blank titrations using water in place ofsulfuric acid solution. The replicate titrations should agreewithin 0.5 percent. Calculate the normality of the bari
37、umchloride solution according to the following equation:NOTE 1In the case of those dimensions for which no specific tolerances are designated above, the permissible variation is 610 % to the nearest 1mm, provided, however, that in no case shall the deviation be greater than 5 mm.FIG. 2 Detailed Draw
38、ing of Combustion and Absorption Apparatus for Sulfur DeterminationFIG. 3 Suction System for Sulfur DeterminationD1072 06 (2017)3Normality of Barium Chloride 510.0 mL x N Sulfuric Acidavg. mL 2 avg. blank!(2)7.4 An auto titration can be used to determine the concen-tration of both sodium hydroxide a
39、nd sulfuric acid.8. Preparation of Apparatus8.1 Place 300 to 400 mL of NaOH solution in the firstscrubber (Fig. 4) and the same amount of H2O2-H2SO4solution(300 mL of water, 30 mL of H2SO4, and 30 mL of H2O2(30 %w/w) in the second scrubber. Replace these solutions when-ever the volume becomes less t
40、han two thirds of the original.8.2 When the apparatus is first assembled, adjust the valvebetween the vacuum manifold and the spray trap so thatapproximately 3 L of air per minute will be drawn through theabsorber when the chimney outlet is open to the atmosphere,the absorber is charged with 30 6 2
41、mL of water, and thepressure in the vacuum manifold is maintained at approxi-mately 40 cm of water below atmospheric. When all adjust-ments have been made, remove the water from the absorbers.8.3 With the burner control valve closed, the valve to thevacuum regulator fully open, and the pressure in t
42、he vacuummanifold adjusted to approximately 40 cm of water belowatmospheric, turn on the purified air. Adjust the chimneymanifold control valve so that, at the required flow through theabsorber, only a small stream of air escapes at the pressure-relief valve, a small stream of air enters at the vacu
43、umregulator, and the pressure in the chimney manifold is 1 to 2 cmof water. Minor adjustment of the vacuum regulator andvacuum control valve may be necessary to achieve thiscondition.NOTE 1It is convenient to balance the air-flow system by regulatingthe pressure in the vacuum manifold. This is done
44、by raising or loweringthe air-inlet tube in the vacuum regulator by sliding it in a rubber sleeve.8.4 When first assembling the apparatus, connect the gassample line using glass or aluminum tubing to the inlet of theflowmeter. Connect the outlet of the flowmeter in a similar wayto the lower side arm
45、 of the burner. Adjust the valve forcontrolling the rate of flow of gas so that gas is burned at a rateto liberate approximately 250 to 500 Btu/h (Note 2). This rateshould be indicated by two index marks on the columns of theflowmeter U-tube or timing a rate-index device. Make theprimary air connect
46、ion from the purified air line to the upperside arm of the burner by means of rubber or plastic tubing.NOTE 2Using this gas rate, the chimney and absorber should notbecome overheated during a test. The appropriate volumetric rate of gasflow will therefore depend on the heating value of the gas being
47、 tested.8.5 Wash the spray trap, absorber, and chimney well withwater before each test. Charge the larger bulb of the absorberwith 10 mL of Na2CO3solution (Note 3) and 20 mL of water.Attach the spray trap and chimney, and connect them,respectively, to the vacuum line and to the purified air lineusin
48、g rubber or plastic tubing. Close the chimney openingusing a cork or other suitable plug.NOTE 3This quantity of Na2CO3solution is adequate to absorb theSO2from the combustion products of 1 ft3of gas containing 15 grains ofsulfur per 100 ft3(0.03 m3of gas containing 350 mg/m3of sulfur.) Forhigher con
49、centrations of sulfur in the gas, the volume of Na2CO3solutionshould be proportionately increased, but the total initial liquid volume inthe absorber should not exceed 30 mL.9. Procedure9.1 Prior to each test, purge the flowmeter, burner, andconnection with the gas sample, and light the flame on theburner. Adjust the gas-flow rate by its valve to conform withthe requirements prescribed in 8.4. Adjust the primary air flowso that a soft blue flame is obtained, with no yellow tip.9.2 To start a determination, insert the burner into thechimney, fastenin
