ASTM D968-2015 Standard Test Methods for Abrasion Resistance of Organic Coatings by Falling Abrasive《采用落砂法测定有机涂层耐磨性的标准试验方法》.pdf
《ASTM D968-2015 Standard Test Methods for Abrasion Resistance of Organic Coatings by Falling Abrasive《采用落砂法测定有机涂层耐磨性的标准试验方法》.pdf》由会员分享,可在线阅读,更多相关《ASTM D968-2015 Standard Test Methods for Abrasion Resistance of Organic Coatings by Falling Abrasive《采用落砂法测定有机涂层耐磨性的标准试验方法》.pdf(5页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: D968 15Standard Test Methods forAbrasion Resistance of Organic Coatings by FallingAbrasive1This standard is issued under the fixed designation D968; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revi
2、sion. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S. Department of Defense.1. Scope1.1 These test methods cover the determinatio
3、n of theresistance of organic coatings to abrasion produced by abrasivefalling onto coatings applied to a plane rigid surface, such as ametal or glass panel.1.2 Two test methods based on different abrasives arecovered as follows:SectionsMethod AFalling Sand Abrasion Test 613Method BFalling Silicon C
4、arbide Abrasion Test 14211.3 These methods should be restricted to testing in onlyone laboratory when numerical values are used because of thepoor reproducibility of the methods (see 13.1.2 and 21.1.2).Interlaboratory agreement is improved significantly when rank-ing is used in place of numerical va
5、lues.1.4 The values stated in SI units are to be regarded as thestandard. The values given in parentheses are for informationonly.1.5 This standard does not purport to address the safetyconcerns, if any, associated with its use. It is the responsibilityof the user of this standard to establish appro
6、priate safety andhealth practices and determine the applicability of regulatorylimitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D823 Practices for Producing Films of Uniform Thicknessof Paint, Varnish, and Related Products on Test PanelsD1005 Test Method for Measurement of Dry-Fil
7、m Thick-ness of Organic Coatings Using MicrometersD7091 Practice for Nondestructive Measurement of DryFilm Thickness of Nonmagnetic Coatings Applied toFerrous Metals and Nonmagnetic, Nonconductive Coat-ings Applied to Non-Ferrous MetalsE11 Specification for Woven Wire Test Sieve Cloth and TestSieves
8、2.2 Other Standards:ANSI B74.12 Specifications for the Size of Abrasive Grain Grinding Wheels, Polishing and General IndustrialUses3FEPA Standard 42-2:2006 Grains of Fused AluminumOxide, Silicon Carbide and other Abrasive Materials forBonded Abrasives and for General Applications Mi-crogrits F230 to
9、 F200043. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 abrasion resistance, nthe amount of abrasive re-quired to wear through a unit film thickness of the coating.4. Summary of Test Method4.1 Abrasive is allowed to fall from a specified heightthrough a guide tube onto a coated
10、 panel until the substratebecomes visible. The amount of abrasive per unit film thick-ness is reported as the abrasion resistance of the coating on thepanel. Silica sand or silicon carbide may be used, as specified.5. Significance and Use5.1 Silica sand produces a slower rate of abrasion fororganic
11、coatings than that provided by silicon carbide. Forsome types of coatings, it may also provide greater differen-tiation.5.2 The abrasion resistance scales produced by the twomethods differ, but the methods provide approximately thesame rankings of coatings for abrasion resistance.1These test methods
12、 are under the jurisdiction of ASTM Committee D01 onPaint and Related Coatings, Materials, and Applications and are the directresponsibility of Subcommittee D01.23 on Physical Properties of Applied PaintFilms.Current edition approved June 1, 2015. Published June 2015. Originallyapproved in 1948. Las
13、t previous edition approved in 2010 as D968 05 (2010).DOI: 10.1520/D0968-15.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onth
14、e ASTM website.3Available from American National Standards Institute (ANSI), 25 W. 43rd St.,4th Floor, New York, NY 10036, http:/www.ansi.org.4Available from Federation of European Producers of Abrasives (FEPA), 20, av.Reille, Paris, F-75014, www.fepa-abrasives.org.Copyright ASTM International, 100
15、Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States15.3 Each of the methods has been found useful for rating theabrasion resistance of specific types of coatings. For exampleMethod A (falling sand) has been used for rating floor coatingswhile Method B (falling silicon car
16、bide) has been used forrating coatings for ship decks.METHOD AFALLING SAND ABRASION TEST56. Apparatus and Materials6.1 Abrasion Tester, as illustrated in Fig. 1 and Fig. 2.Agatefor starting the flow of abrasive is located near the top of theguide tube. It consists of a metal disk inserted into a sli
17、t in theside of the guide tube with a collar covering the slit. The guidetube shall be firmly supported in a vertical position over asuitable receptacle, which shall contain a support for holdingthe coated panel at an angle of 45 to the vertical. The openingof the tube is directly above the area to
18、be abraded and thedistance from the tube to the coated surface face at the nearestpoint is 25 mm (1 in.) when measured in the vertical direction.The base of the apparatus shall be fitted with adjusting screwsfor properly aligning the equipment.6.2 Standard AbrasiveNatural silica sand from the St.Pet
19、ers or Jordan sandstone deposits (located in the centralUnited States) shall be considered standard when graded asfollows after 5 min of continuous sieving.0 % retained on a No. 16 (1.18 mm) sieveMaximum 15 % retained on a No. 20 (850 m) sieveMinimum 80 % retained on a No. 30 (600 m) sieveMaximum 5
20、% passing a No. 30 (600 m) sieveThe sand is characterized by its roundness of grains and hasa silicon dioxide content greater than 99 %. Use the sievesdescribed in Specification E11.NOTE 1The abrading qualities of sand obtained from different sourcesmay differ slightly even though the sand meets the
21、 sieve requirements.Therefore, for maximum precision of test results, purchaser and sellershould use sand from the same source.7. Test Specimens7.1 Apply uniform coatings of the material to be tested to aplane, rigid surface such as a metal or glass panel. Prepare aminimum of two coated panels for t
22、he material.7.2 Cure the coated panels under the conditions of humidityand temperature agreed upon between the purchaser and seller.NOTE 2The coatings should be applied in accordance with PracticesD823, or as agreed upon between the purchaser and the seller.NOTE 3The thickness of the dry coatings sh
23、ould be measured inaccordance with Test Methods D1005 or D7091.NOTE 4While the minimum of two coated panels is acceptable,evaluating three or more panels per material will provide greater confi-dence in your test results.8. Standardization8.1 Pour a quantity of standard sand into the funnel andexami
24、ne the sand stream falling from the lower end of theguide tube. Align the apparatus by means of the adjustingscrews in the base until the inner concentrated core of the sandstream falls in the center of the flow when viewed at twopositions at 90 to each other. Introduce a measured volume of5Hipkins,
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
最后一页预览完了!喜欢就下载吧,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMD9682015STANDARDTESTMETHODSFORABRASIONRESISTANCEOFORGANICCOATINGSBYFALLINGABRASIVE 采用 落砂法 测定 有机 涂层

链接地址:http://www.mydoc123.com/p-512598.html