1、Designation: D3005 10D3005 17 An American National StandardStandard Specification forLow-Temperature Resistant Vinyl Chloride Plastic Pressure-Sensitive Electrical Insulating Tape1This standard is issued under the fixed designation D3005; the number immediately following the designation indicates th
2、e year oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This specification covers an electrical insulatin
3、g tape for use at low temperature down to approximately 18 C (0 F).-18C (0F). The tape consists of a backing of vinyl chloride plastic, coated on one side with a pressure-sensitive adhesive. Fourtypes are included providing two thicknesses at two operating temperatures.1.2 The values stated in SI un
4、its are the standard. The values given in parentheses are provided for information purposes only.2. Referenced Documents2.1 ASTM Standards:2D1000 Test Methods for Pressure-Sensitive Adhesive-Coated Tapes Used for Electrical and Electronic ApplicationsD1711 Terminology Relating to Electrical Insulati
5、on3. Terminology3.1 DefinitionsFor definitions of terms in this specification refer to Terminology D1711.4. Classification4.1 This specification covers two types of vinyl chloride plastic tape of different thicknesses, as follows:4.1.1 Type I0.0178-mm (0.007-in.) standard backing for use at low temp
6、erature down to 7 C (19.4 F).-7C (19.4F).4.1.2 Type II0.216-mm (0.0085-in.) standard backing for use at low temperature down to 7 C (19.4 F).-7C (19.4F).4.1.3 Type III0.0178-mm (0.007-in.) standard backing for use at low temperature down to 18 C (0 F).-18C (0F).4.1.4 Type IV0.216-mm (0.0085-in.) sta
7、ndard backing for use at low temperature down to 18 C (0 F).-18C (0F).5. Materials5.1 The backing shall be vinyl chloride plastic, suitably compounded to meet the requirements of this specification. The backingshall be smooth and uniform. The tape edges shall be straight and unbroken.5.2 The pressur
8、e-sensitive adhesive coating shall be smooth and uniform, and essentially free of lumps and bare spots. “Fisheyes” shall not be cause for rejection. There shall be no adhesive transfer when the tape is unwound from the roll.6. Physical Properties6.1 The tape shall meet the requirements given in Tabl
9、e 1.6.2 Black plastic backing shall be considered standard. Backing of a different color than black shall be specified on the purchaseorder.7. Standard Rolls7.1 The standard widths and lengths shall be selected from the following:7.1.1 Widths:1 This specification is under the jurisdiction of ASTM Co
10、mmittee D09 on Electrical and Electronic Insulating Materials and is the direct responsibility of SubcommitteeD09.07 on Flexible and Rigid Electrical Insulating Materials.Current edition approved May 1, 2010Feb. 15, 2017. Published June 2010February 2017. Originally approved in 1972. Last previous e
11、dition approved in 20042010 asD300593(2004).D3005 10. DOI: 10.1520/D3005-10.10.1520/D3005-17.2 For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at serviceastm.org. For Annual Book of ASTM Standardsvolume information, refer to the standards Document S
12、ummary page on the ASTM website.This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM recomme
13、nds that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered the official document.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700,
14、 West Conshohocken, PA 19428-2959. United States1mm in. mm in.6 14 22 789 38 25 112 12 30 11415 58 38 11219 34 50 2mm in. mm in.6 14 22 789 38 25 112 12 30 11415 58 38 11219 34 50 27.1.1.1 Widths greater than 2 in. (50 mm) shall be agreed upon between the purchaser and the seller.7.1.2 Lengths:m ft6
15、 2220 6633 108TABLE 1 Requirements for Low-Temperature Vinyl Chloride Plastic Electrical TapeProperties Type I Type II Type III Type IVThickness, mm (in.) avg 0.178 0.025 0.216 0.025 0.178 0.025 0.216 0.025(0.007 0.001) (0.0085 0.001) (0.007 0.001) (0.0085 0.001)Width, tolerance, mm (in.) 0.8 (132)
16、0.8 (132) 0.8 (132) 0.8 (132)Length, tolerance, min, % 1.0 1.0 1.0 1.0Length, tolerance, min, % -1.0 -1.0 -1.0 -1.0Break strength, min, kN/m (lbf/in.) avg 2.6 (15) 2.9 (17) 2.6 (15) 2.9 (17)Break elongation, min, % avg: 150 150 200 200at 7 C avg 100A 100Aat -7C avg 100A 100Aat 18 C avg 100A 100Aat -
17、18C avg 100A 100ADielectric breakdown, min V avg:Standard condition 7000 8500 7000 8500Wet condition (96/23/96) 90 % of dry 90 % of dry 90 % of dry 90 % of dryAdhesion, min, N/m (ozf/in.) avgSteel at 23 C avg 175 (16) 175 (16) 175 (16) 175 (16)Steel at 23C avg 175 (16) 175 (16) 175 (16) 175 (16)at 7
18、 C avg 175 (16) 175 (16)at -7C avg 175 (16) 175 (16)at 18 C avg 328 (30) 328 (30)at -18C avg 328 (30) 328 (30)Backing at 23 C avg 175 (16) 175 (16) 175 (16) 175 (16)Backing at 23C avg 175 (16) 175 (16) 175 (16) 175 (16)at 7 C avg 175 (16) 175 (16)at -7C avg 175 (16) 175 (16)at 18 C avg 175 (16) 328
19、(30)at -18C avg 175 (16) 328 (30)Roll Unwind, N/m (ozf/in.) avgat 23 C, min 197 (18) 197 (18) 197 (18) 197 (18)at 23C, min 197 (18) 197 (18) 197 (18) 197 (18)max 328 (30) 328 (30) 328 (30) 328 (30)at 7 C min 350 (32) 350 (32)at -7C min 350 (32) 350 (32)max 1400 (128) 1400 (128)at 18 C, min 350 (32)
20、350 (32)at -18C, min 350 (32) 350 (32)at 18 C min, % avg 15 15High-humidity insulation resistance,min, M median1 106 1 106 1 106 1 106Flagging, max, mm (in.) avg 6.5 (0.3) 6.5 (0.3) 6.5 (0.3) 6.5 (0.3)Flammability, max, s 4 4 4 4A Razor slit.D3005 172m ft6 2020 6633 1087.1.2.1 Lengths greater than 3
21、3 m (108 ft) shall be in multiples of 108 ft. Additional lengths shall be agreed upon between thepurchaser and seller.8. Test Methods8.1 The selection of rolls, conditioning, and testing shall be in accordance with Test Methods D1000.9. Rejection9.1 If the test results of any roll do not conform to
22、the requirements prescribed in the specification, two additional rolls shallbe selected and tested. If one of the two additional sample rolls also does not conform to the requirements, it is acceptable for thelot mayto be rejected at the option of the purchaser.10. Packaging and Package Marking10.1
23、PackagingThe package shall withstand shipment and shall give the product ample protection against damage. Theindividual rolls shall not adhere to each other or to the container.10.2 Package MarkingEach package shall be marked with the name of the manufacturer, the manufacturers product number,and th
24、e width and length of the roll.11. Keywords11.1 electrical insulating tape; low-temperature vinyl chloride plastic tape; plastic electrical tape; pressure-sensitive adhesivetape; vinyl chloride plastic tapeSUMMARY OF CHANGESCommittee D09D09 has identified the location of selected changes to this spe
25、cificationstandard since the lastissue, issue (D300593(2004)D3005 10,) that may impact the use of this specification.standard. (ApprovedMay 1, 2010Feb. 15, 2017).)(1) Revised Table 1.(1) Revised 5.2 and Table 1.ASTM International takes no position respecting the validity of any patent rights asserte
26、d in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by th
27、e responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn.Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive c
28、areful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM Internati
29、onal, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 173
