1、Designation: D 3892 93 (Reapproved 2009)Standard Practice forPackaging/Packing of Plastics1This standard is issued under the fixed designation D 3892; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A num
2、ber in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope1.1 This practice covers the packaging and packing of allther
3、moset and thermoplastic resins and fabricated shapes.1.2 This standard does not purport to address all of thesafety problems, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility o
4、f regulatory limitations prior to use.NOTE 1There is no similar or equivalent ISO standard.2. Referenced Documents2.1 ASTM Standards:2D 883 Terminology Relating to Plastics2.2 Federal Standards:Department of Transportation 19A, Title 49, Code of Fed-eral Regulations, Section 178.190, Wooden BoxesGlu
5、ed, Plywood Cleated3Department of Transportation 17H, Title 49, Code of Fed-eral Regulations, Section 178.118, Steel Drums32.3 Other Standards:National Motor Freight Classification4Uniform Freight Classification Rules53. Terminology3.1 Definitions: For definitions of technical terms used inthis prac
6、tice pertaining to plastics, see Terminology D 883.4. Significance and Use4.1 Packing and packaging provisions are outlined asneeded for adequate transport of resins and finished productswith a minimum of mishaps in shipment.4.2 Commercial levels are included for all commercial andmost federal and m
7、ilitary shipments. Level A requirements areadded for special military purchases only.5. Procedure5.1 Examination of Preparation for DeliveryExamine inaccordance with Table 1 to determine that packaging, packing,and marking comply with requirements specified in the con-tract or order. The sample unit
8、 for this examination shall be oneshipping container fully prepared for delivery.5.2 PackagingPackaging shall be commercial or Level A,as specified.5.2.1 CommercialThe material shall be packaged in ac-cordance with normal commercial practice. The completepackage shall be designed to ensure the item
9、against damageduring shipment, handling, and storage.5.2.2 Level AFor Military Procurement Only:5.2.2.1 Sheets, Rods, Tubes, Pipes, Fittings, and OtherShapesUnless otherwise specified in the contract or order,individual fabricated shapes shall be packaged in such amanner as to protect the material a
10、gainst physical and mechani-cal damage and contamination during transit. Only itemscomprised of a single National Stock number (NSN) oridentifying number shall be placed in one package. Individualsheets shall be masked or interleaved.5.2.2.2 Rolls of Film or SheetingThese shall be suppliedin rolls.
11、Each roll shall be wrapped with at least one layer ofpolyethylene film or kraft paper, and tightly sealed with tape toprevent contamination.5.3 PackingPacking shall be commercial or Level A, asspecified.5.3.1 CommercialThe material shall be packed in accor-dance with normal commercial practice. The
12、packaged mate-rial shall be packed to assure acceptance by common carrierand to provide product protection against loss and damageduring multiple shipments, handling, and storage. The shipping1This practice is under the jurisdiction ofASTM Committee D20 on Plastics andis the direct responsibility of
13、 Subcommittee D20.94 on Government/IndustryStandardization.Current edition approved April 1, 2009. Published April 2009. Originallyapproved in 1980. Last previous edition approved in 2003 as D 3892 - 93 (2003).2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Custo
14、mer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from U.S. Government Printing Office Superintendent of Documents,732 N. Capitol St., NW, Mail Stop: SDE, Washington, DC 20401, http:/www.acc
15、ess.gpo.gov.4Available fromAmerican TruckingAssn., 1616 PStreet, N.W., Washington, DC20036.5Available from Railroad Freight Classification, Room 1106, 222 South River-side Plaza, Chicago, IL 60606.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, Un
16、ited States.container shall be in compliance with National Motor FreightClassification and Uniform Freight Classification Rules.5.3.2 Level A (For Military Procurement Only):5.3.2.1 Sheets, Rods, Tubes, Film, and Other ShapesThematerials packaged as specified in 5.2.2.1 and 5.2.2.2 shall bepacked in
17、 plywood cleated boxes conforming to Department ofTransportation (DOT) 19A. All items packed together must beof the same technical description.5.3.2.2 Resin, Powder, GranulesUnless otherwise speci-fied, the material in the quantity specified shall be packed inmetal drums conforming to DOT 17H. Insof
18、ar as practical,containers shall be of uniform shape and size, with minimumcube and tare consistent with the protection required. All itemspacked together must be of the same technical description.5.4 MarkingMarking for interior packages and shippingcontainers shall be as specified in the contract o
19、r order.6. Ordering Information6.1 All orders shall include the following information:6.1.1 Title, number, and date of this practice: ASTM D3892,6.1.2 Type of material required,6.1.3 Color required, with tolerance and method of deter-mination, including whether determination shall be made onunproces
20、sed material or molded specimens,6.1.4 Form and uniformity required, when so specified,6.1.5 Level of packaging/packing required, and6.1.6 Marking requirements.7. Keywords7.1 containers; film; marking; packaging; packing; plastics;shapes; sheetingASTM International takes no position respecting the v
21、alidity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is s
22、ubject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headq
23、uarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This stan
24、dard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or se
25、rviceastm.org (e-mail); or through the ASTM website(www.astm.org).TABLE 1 Examination for Defects in Preparation for DeliveryExamine DefectPackaging Not level specified. Packaging material not asspecified.Packing Not level specified. Containers not as specified.Count Less than specified or indicated quantity.Weight and cube Gross weight is greater than, or less than, specifiedrequire-ments.Markings Markings not in accordance with specifiedrequirements.D 3892 93 (2009)2
