1、Designation: D 6506 01Standard Specification forAsphalt Based Protection Board for Below-GradeWaterproofing1This standard is issued under the fixed designation D 6506; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of las
2、t revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers an asphalt based protectionboard used for protecting the integrity of below grade or belowwear
3、ing surface waterproofing. The protection board protectsthe waterproofing system from backfill, surfacing, constructionactivities, and weathering conditions prior to backfilling orapplying surfacing.1.2 The values stated in SI units are to be regarded as thestandard. The values given in parentheses
4、are for informationonly.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prio
5、r to use.2. Referenced Documents2.1 ASTM Standards:D 545 Test Methods for Preformed Expansion Joint Fillersfor Concrete Construction (Nonextruding and ResilientTypes)2D 994 Specification for Preformed Expansion Joint Fillerfor Concrete (Bituminous Type)2D 5147 Test Methods for Sampling and Testing M
6、odifiedBituminous Sheet Material3E 154 Test Methods for Water Vapor Retarders Used inContact with Earth Under Concrete Slabs, on Walls, or asGround Cover43. Classification3.1 Two Classes of Product are Covered in This Specifica-tion:3.1.1 Class A, is made with asphalt saturated organic felt onthe bo
7、ttom and a coated or saturated non-woven glass felt ontop.3.1.2 Class B, is made with glass fabrics both top andbottom.3.1.3 Classes A and B, each include three thicknesses ofboard. If desired, one side of each of these classes may becovered with a thin plastic antistick sheet.4. Materials and Manuf
8、acture4.1 The protection board shall be comprised of layers ofasphalt and reinforcing mat. One surface of the board will beuniformly coated with a bituminous material for limitedweather protection.4.2 The length and width measurements shall be as specifiedby the manufacturer. The tolerances of these
9、 dimensions(length and width) shall be 66mm(14 in.)4.3 The surfaces of the protection board shall be uniformand free from defects such as cracks and indentations. Theedges shall be uniform.5. Sampling5.1 Each sample shall consist of sufficient material toprovide at least five specimens for the tests
10、 listed in Section 7.One representative sample shall be selected for each shipmentof 10 000 ft2or fraction thereof.6. Physical Requirements6.1 Nominal thicknesses of protection board are as follows:6.1.1 Type 1, board is116 in.6.1.2 Type 2, board is18 in.6.1.3 Type 3, board is14 in.6.2 Class A prote
11、ction board shall conform to the require-ments in Table 1.6.3 Class B protection board shall conform to the require-ments in Table 2.7. Test Methods7.1 ThicknessDetermine the thickness of the specimenusing vernier calipers in accordance with Test MethodsD 5147, Section 5.7.2 Puncture StrengthDetermi
12、ne in accordance with TestMethods E 154, Section 10.7.3 Water AbsorptionDetermine in accordance withSpecification D 994, 8.3.1This specification is under the jurisdiction of ASTM Committee D08 onRoofing, Waterproofing and Bituminous Materials and is the direct responsibility ofSubcommittee D08.22 on
13、 Waterproofing and Damproofing Systems.Current edition approved May 10, 2001. Published August 2001.2Annual Book of ASTM Standards, Vol 04.03.3Annual Book of ASTM Standards, Vol 04.04.4Annual Book of ASTM Standards, Vol 04.11.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Co
14、nshohocken, PA 19428-2959, United States.7.4 Asphalt ContentDetermine according to Test MethodsD 545, 7.5.7.5 Resistance to DecayDetermine according to TestMethods E 154, Section 13.8. Keywords8.1 protection board; waterproofingASTM International takes no position respecting the validity of any pate
15、nt rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision
16、at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comme
17、nts will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted
18、 by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-ma
19、il); or through the ASTM website(www.astm.org).TABLE 1 Class A Protection Board RequirementsType 1 Type 2 Type 3Puncture Strength 222 N (50 lbf) minimum 312 N (70 lbf) minimum 365 N (82 lbf) minimumThickness 1.3 to 1.8 mm (0.050 to 0.070 in.) 2.4 to 3.9 mm (0.095 to 0.155 in.) 5.6 to 7.1 mm (0.220 t
20、o 0.280 in.)Water Absorption 10.0 % maximum 10.0 % maximum 10.0 % maximumAsphalt, % by weight 65 % minimum 65 % minimum 65 % minimumResistance to Decay Meets puncture requirements aftercompletion of testMeets puncture requirements aftercompletion of testMeets puncture requirementsafter completion of
21、 testTABLE 2 Class B Protection Board RequirementsType 1 Type 2 Type 3Puncture Strength 222 N (50 lbf) minimum 312 N (70 lbf) minimum 365 N (82 lbf) minimumThickness 1.3 to 1.8 mm (0.050 to 0.070 in.) 2.4 to 3.9 mm (0.095 to 0.155 in.) 5.6 to 7.1 mm (0.220 to 0.280 in.)Water Absorption 10.0 % maximum 10.0 % maximum 10.0 % maximumAsphalt, % by weight 40 % minimum 40 % minimum 40 % minimumResistance to Decay Meets puncture requirements aftercompletion of testMeets puncture requirements aftercompletion of testMeets puncture requirementsafter completion of testD6506012
