ASTM D6622-2001(2009) 895 Standard Guide for Application of Fully Adhered Hot-Applied Reinforced Waterproofing Systems《完全粘结的热铺增强防水系统应用的标准指南》.pdf
《ASTM D6622-2001(2009) 895 Standard Guide for Application of Fully Adhered Hot-Applied Reinforced Waterproofing Systems《完全粘结的热铺增强防水系统应用的标准指南》.pdf》由会员分享,可在线阅读,更多相关《ASTM D6622-2001(2009) 895 Standard Guide for Application of Fully Adhered Hot-Applied Reinforced Waterproofing Systems《完全粘结的热铺增强防水系统应用的标准指南》.pdf(4页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: D 6622 01 (Reapproved 2009)Standard Guide forApplication of Fully Adhered Hot-Applied ReinforcedWaterproofing Systems1This standard is issued under the fixed designation D 6622; the number immediately following the designation indicates the year oforiginal adoption or, in the case of re
2、vision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This guide covers the minimum installation recommen-dations for fully adhered, hot-applied reinfor
3、ced waterproofingsystems on vertical and low-slope (plaza deck) surfaces.1.2 For the purpose of this guide, the substrate is assumed tobe concrete or masonry, structurally sound, able to accept theweight of anticipated loads, and meets the local building coderequirements. Similarly, all components o
4、f the waterproofingsystem are assumed to comply with any federal, state, and localenvironmental regulations that may be in effect at the time ofinstallation. Expansion joints, insulation, drainage layers, andoverburden are beyond the scope of this guide.1.3 The values stated in SI units are to be re
5、garded as thestandard. The values given in parentheses are for informationonly.1.4 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and dete
6、rmine the applica-bility of regulatory requirements prior to use.2. Referenced Documents2.1 ASTM Standards:2C 981 Guide for Design of Built-Up Bituminous MembraneWaterproofing Systems for Building DecksD41 Specification for Asphalt Primer Used in Roofing,Dampproofing, and WaterproofingD43 Specificat
7、ion for Coal Tar Primer Used in Roofing,Dampproofing, and WaterproofingD 173 Specification for Bitumen-Saturated Cotton FabricsUsed in Roofing and WaterproofingD 226 Specification for Asphalt-Saturated Organic FeltUsed in Roofing and WaterproofingD 227 Specification for Coal-Tar-Saturated Organic Fe
8、ltUsed in Roofing and WaterproofingD 449 Specification for Asphalt Used in Dampproofing andWaterproofingD 450 Specification for Coal-Tar Pitch Used in Roofing,Dampproofing, and WaterproofingD 1079 Terminology Relating to Roofing and Waterproof-ingD 1327 Specification for Bitumen-Saturated Woven Burl
9、apFabrics Used in Roofing and WaterproofingD 1668 Specification for Glass Fabrics (Woven andTreated) for Roofing and WaterproofingD 2178 Specification for Asphalt Glass Felt Used in Roof-ing and WaterproofingD 2822 Specification for Asphalt Roof Cement, Asbestos-ContainingD 4022 Specification for Co
10、al Tar Roof Cement, AsbestosContainingD 4586 Specification for Asphalt Roof Cement, Asbestos-FreeD 4990 Specification for Coal Tar Glass Felt Used inRoofing and WaterproofingD 5295 Guide for Preparation of Concrete Surfaces forAdhered (Bonded) Membrane Waterproofing SystemsD 5643 Specification for C
11、oal Tar Roof Cement, AsbestosFreeD 5726 Specification for Thermoplastic Fabrics Used inHot-Applied Roofing and WaterproofingD 5898 Guide for Details for Adhered Sheet WaterproofingD 5957 Guide for Flood Testing Horizontal WaterproofingInstallationsD 6152 Specification for SEBS-Modified Mopping Aspha
12、ltUsed in RoofingD 6162 Specification for Styrene Butadiene Styrene (SBS)Modified Bituminous Sheet Materials Using a Combina-tion of Polyester and Glass Fiber ReinforcementsD 6163 Specification for Styrene Butadiene Styrene (SBS)Modified Bituminous Sheet Materials Using Glass FiberReinforcementsD 61
13、64 Specification for Styrene Butadiene Styrene (SBS)Modified Bituminous Sheet Materials Using PolyesterReinforcements1This guide is under the jurisdiction of ASTM Committee D08 on Roofing andWaterproofing and is the direct responsibility of Subcommittee D08.22 on Water-proofing and Dampproofing Syst
14、ems.Current edition approved Jan. 1, 2009. Published January 2009. Originallyapproved in 2001. Last previous edition approved in 2001 as D 6622 01.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandard
15、s volume information, refer to the standards Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.D 6451 Guide for Application of Asphalt Based ProtectionBoardD 6506 Specification for Asphalt Based
16、 Protection Boardfor Below-Grade Waterproofing2.2 Other Documents:CAN/CGSB-37.50 Hot-Applied, Rubberized Asphalt forRoofing and Waterproofing3CAN/CGSB-37.51 Application for Hot-Applied Rubber-ized Asphalt for Roofing and Waterproofing33. Terminology3.1 DefinitionsFor definitions of terms used in thi
17、s guide,refer to Terminology D 1079.4. Classification4.1 The following types are used to identify the waterproof-ing systems included in this guide.4.1.1 Type IMembranes consisting of hot-applied coal tarpitch, and two or more layers of organic or inorganic felts orfabrics.4.1.2 Type IIMembranes con
18、sisting of hot-applied as-phalt, and two or more layers of organic or inorganic felts orfabrics.4.1.3 Type IIIMembranes consisting of hot-applied as-phalt or polymer-modified asphalt, and one or more polymer-modified bitumen sheets. The sheets are typically SBS-modified bitumen and may be reinforced
19、 with fiberglass, orpolyester, or both.4.1.4 Type IVMembranes consisting of hot-appliedpolymer-modified asphalt, and fabric reinforcement.5. Significance and Use5.1 This guide outlines general procedures and precautionsfor the application of fully adhered hot-applied built-up rein-forced waterproofi
20、ng systems.5.2 This guide is not all inclusive and is intended only tosupplement detailed instructions from designers, and the rec-ommendations of manufacturers. Manufacturers of some of thesystems addressed by this guide require proprietary productsand special procedures not described in this guide
21、. Manufac-turers recommendations should therefore be considered in theapplication of this guide.5.3 For design guidelines, consult Guide C 981.6. Delivery of Materials6.1 Deliver materials in the manufacturers original un-opened packages and containers.6.2 All materials or material packaging must be
22、 clearlymarked in a weather-resistant manner with type, stock, or lotnumber, and other pertinent information, for example, size,manufacturers name, ASTM specification, flash point,equiviscous temperature, or other application information.7. Storage and Handling of Materials7.1 Store materials on rai
23、sed platforms or pallets. Store rollsvertically or horizontally, as recommended by the roll manu-facturer. Store materials in a dry, ventilated and weatherprooflocation. Avoid damage or embedment of foreign materials.7.2 Store materials to prevent system suppliers markingsfrom being destroyed.7.3 Wh
24、en used as part of the system, store primer andmastic in tightly closed original containers at temperaturesrecommended by the system supplier.8. Safety Precautions8.1 Safety precautions include, but are not limited to: wearprotective clothing, vent fumes especially in confined spaces,avoid contact w
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
最后一页预览完了!喜欢就下载吧,查找使用更方便
5000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMD662220012009895STANDARDGUIDEFORAPPLICATIONOFFULLYADHEREDHOTAPPLIEDREINFORCEDWATERPROOFINGSYSTEMS

链接地址:http://www.mydoc123.com/p-523080.html