1、Designation: D7849 14Standard Classification forNomenclature of Reference Materials of Committee D241This standard is issued under the fixed designation D7849; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revisi
2、on. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This classification covers instructions for naming thereference materials used by Committee D24.1.2 This standard does not purpor
3、t to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D1510
4、 Test Method for Carbon BlackIodine AdsorptionNumberD2414 Test Method for Carbon BlackOil AbsorptionNumber (OAN)D3265 Test Method for Carbon BlackTint StrengthD3493 Test Method for Carbon BlackOil AbsorptionNumber of Compressed Sample (COAN)D6556 Test Method for Carbon BlackTotal and ExternalSurface
5、 Area by Nitrogen Adsorption3. Significance and Use3.1 Standard reference materials are used for calibration andverification of many carbon black tests under the jurisdiction ofD24. This practice defines a systematic means of naming thesereference materials and does so in a manner to clearlydifferen
6、tiate between the various reference materials as well astheir version.4. Basis of Classification4.1 ASTM Committee D24 has established four differenttypes of reference materials which serve to improve testprecision of analytical tests on carbon black as well asin-rubber evaluation of carbon black.34
7、.1.1 SRB (Standard Reference Blacks)A set of sevencarbon blacks, six furnace blacks with defined target values foriodine adsorption number (Test Method D1510), STSA (TestMethod D6556), NSA (Test Method D6556), OAN (TestMethod D2414), COAN (Test Method D3493) and TintStrength (Test Method D3265) and
8、one thermal black withdefined values for STSA (Test Method D6556), NSA (TestMethod D6556) and OAN (Test Method D2414). The SRBscan be used to verify analytical test equipment and testprocedures. For OAN and COAN, their application is manda-tory to normalize measured data.4.1.2 ITRB (Industry Tint Re
9、ference Black)ITRB repre-sents a standard carbon black of the N330 type. It is used forverification and standardization in the test method for TintStrength (Test Method D3265).4.1.3 INR (Iodine Number Reference, previously designated“HT”)INR consist of three different reference blacks whichhave been
10、 heat-treated in order to provide particularly highstability of the iodine number over a long period of time, thatis, over many years.4.1.4 IRB (Industry Reference Black)IRB is a carbonblack of the N330 type which is produced in large quantities inorder to serve as a reference material in rubber com
11、pounds.In-rubber properties of this reference black are determinedduring a round robin tests when the material is introduced.4.2 Nomenclature:4.2.1 All letters in the designation are in caps with no spacesor special characters used.4.2.2 The reference material is identified by its type: SRB,ITRB, IN
12、R or IRB.4.2.3 The set number follows, with no special characters orspace as separator, for example: SRB8.4.2.4 In the case where several materials form a set (likeSRB and INR), a letter is added, starting with A in ascendingorder (for example, SRB8A). Preferably the order of the1This classification
13、 is under the jurisdiction of ASTM Committee D24 onCarbon Black and is the direct responsibility of Subcommittee D24.41 on CarbonBlack Nomenclature and Terminology.Current edition approved June 1, 2014. Published June 2014. DOI: 10.1520/D7849-14.2For referenced ASTM standards, visit the ASTM website
14、, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Target values and control limits are published on the website of the distributorof these reference materials, Bale
15、ntine Enterprise Inc.: http:/ ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1materials is in line with a relevant property, like iodineadsorption number for INR.4.2.5 It may occur that a second lot of the same material isproduced after depleti
16、on of the initial lot. In order to distin-guish between both lots, a number is added in chronologicalorder, for example: SRB8A2 (second lot of SRB8A).NOTE 1While the same letters will be used from one set to the next,the materials carrying the same letter designation may or may not be thesame carbon
17、 black.4.3 Examples of how to identify reference materials follow:4.3.1 IRB and ITRB:4.3.1.1 The IRB currently in use in 2013 is identified asIRB8.4.3.1.2 The next IRB in the series will be identified as IRB9.4.3.1.3 The ITRB currently in use in 2013 is identified asITRB since this was the original
18、version of this referencematerial.4.3.1.4 The next ITRB in the series will be identified asITRB2.4.3.2 SRB and INR are sets.4.3.2.1 The SRB set currently in use in 2013 is identified asSRB8. Materials within SRB8 are SRB8A through SRB8Granked in order of tread, carcass, thermal, and then OANnumber w
19、ithin each.4.3.2.2 The next SRB set will be identified as SRB9.4.3.2.3 The INR currently in use in 2013 is identified as INRsince it is the first set of this reference material. This materialis similar to the materials identified as HT1, HT2, and HT3 thatare no longer commercially available. The HT
20、identificationdoes not comply with this identification system but will be usedhistorically as long as the HT materials are in use.4.3.2.4 The current INR set is INRA, INRB, and INRCranked in order of iodine number.4.3.2.5 The next INR set will be identified as INR2A,INR2B, and INR2C.5. Keywords5.1 i
21、ndustry reference black; industry tint reference black;INR; iodine number reference; IRB; ITRB; SRB; standardreference blackASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are exp
22、ressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revis
23、ed, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may
24、 attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United Stat
25、es. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).D7849 142
