1、Designation: F109 12 (Reapproved 2018)Standard Terminology Relating toSurface Imperfections on Ceramics1This standard is issued under the fixed designation F109; the number immediately following the designation indicates the year of originaladoption or, in the case of revision, the year of last revi
2、sion. A number in parentheses indicates the year of last reapproval. A superscriptepsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This terminology describes and illustrates imperfectionsobserved on whitewares and related products. For additionaldefinitions
3、of terms relating to whitewares and relatedproducts, refer to Terminology C242. To observe these defects,examination shall be performed visually, with or without theaid of a dye penetrant, as described in Test Method C949.Agreement by the manufacturer and the purchaser regardingspecific techniques o
4、f observation is strongly recommended.1.2 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recom-mendations issued by the World T
5、rade Organization TechnicalBarriers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:2C242 Terminology of Ceramic Whitewares and RelatedProductsC949 Test Method for Porosity in Vitreous Whitewares byDye PenetrationE165 Practice for Liquid Penetrant Examination for GeneralIndustry3.
6、 Terminologyblemishstrained or discolored area attributable to normalcomposition or forming, or both. (See also inclusion.)blisterbubble or gaseous inclusion at the surface which ifbroken could form a pit, pock, or hole.burrfragment of excess material or foreign particle adheringto the surface.cambe
7、ra single arch of curvature. (See also waviness.)chiparea along an edge or corner where the material hasbroken off.where:w = widthl = length, andd = depth.closed chipfractured area on the edge or corner when thematerial has not broken off (Syn. potential chip).1This terminology is under the jurisdic
8、tion of ASTM Committee C21 onCeramic Whitewares and Related Productsand is the direct responsibility ofC21.01Editorial and Terminology on Nomenclature.Current edition approved Feb. 1, 2018. Published February 2018. Originallyapproved in 1969. Last previous edition approved 2012 as F109 12. DOI:10.15
9、20/F0109-12R18.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International, 100 Barr Harbor
10、Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recommendations
11、 issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.1where:W = widthl = length, andd = depth.crackline of fracture without complete separation.crawlinga parting and contraction of the glaze on the surfaceof ceramic ware during drying or firing, resulting in un-glazed
12、areas bordered by coalesced glaze.crazingthe cracking that occurs in fired glazes or otherceramic coatings as a result of tensile stresses, may alsooccur in the surface portion of uncoated (unglazed) white-ware bodies.finfine feather-edge protrusion from the surface (Syn. flash).flow lineone or more
13、 streaks distinguished by a difference inlight reflectance from the surrounding area, charateristic ofinjection-molded parts. (See also weld mark.)grinding marka pattern of fine striations or scoring, usuallydirectional, resulting from machining, as distinct from sur-face marksholea deep depression
14、or void, the bottom of which is notvisible by normal (20/20) vision under 200 fc illumination.inclusionembedded foreign material or a stain other thanfrom normal composition or forming, or both (see blemish).kinka type of waviness occurring interior to the edges, not tobe confused with the more abru
15、pt departures as ridges orsurface marks. (See also waviness.)lumpa raised area on the surface having the appearance ofbeing solid.F109 12 (2018)2metal markslines on the surface of a ceramic body or glazecaused by drawing a hard metal, such as a knife, across thesurface.peelingcompressive stresses in
16、 a fired glaze or other ceramiccoating of sufficient magnitude to exceed the strength ofadhesion between the glaze and the body.pinholesimperfections in the surface of a ceramic glazeresembling pin pricks.pita shallow depression or crater in which all surfaces arevisible by normal (20/20) vision und
17、er 200 fc of illumina-tion.pocka partially closed surface cavity.where:w = width.porean internal cavity which may be exposed by cutting,grinding, or polishing to become a pit, pock, or hole.F109 12 (2018)3porous areaan area that will retain dye when tested inaccordance with Practice E165 and, if bro
18、ken through at theporous area, will show evidence of dye penetration into thebody.ridgelong, narrow protrusion on any surface.rima protrusion, usually of base material, bordering eitherpartially or completelly a hole, pit, or pock.specka discrete particle of unreacted or unwanted material ina cerami
19、c body or glaze.straightness of sidesthe deviation from straightness of thecenter of the side in the plane of the tile, as measured by awedging apparatus (C-502). The measurement is only rel-evant to the straight sides of tiles.surface marksrelatively long, narrow, shallow grooves orcuts in the surf
20、ace, such as scratches, score marks, andmachining marks. (See also grinding markwavinessa long-order departure from flatness as opposed tosharp discontinuities. Amplitude is in excess of specifiedsurface finish. In general, waviness will exhibit a number ofinflection points that, if connected, would
21、 form a line whosepath may be open or closed (Syn. warp).weld marka deep groove or fissure formed by incompleteunion of two or more particles or streams of material flowingtogether.F109 12 (2018)4ASTM International takes no position respecting the validity of any patent rights asserted in connection
22、 with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible t
23、echnical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful conside
24、ration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr
25、 Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 12 (2018)5
