1、Designation: F 1018 87a (Reapproved 2004)An American National StandardStandard Specification forSteel Emergency Gear Stowage Locker1This standard is issued under the fixed designation F 1018; the number immediately following the designation indicates the year oforiginal adoption or, in the case of r
2、evision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers the design, material, andmanufacture of steel emergency gear stowage l
3、ockers.1.2 Emergency gear lockers shall be of four types (seeSection 3).1.3 The values stated in inch-pound units are to be regardedas the standard. The values given in parentheses are forinformation only.2. Referenced Documents2.1 ASTM Standards:2A 36/A 36M Specification for Carbon Structural Steel
4、A 276 Specification for Stainless Steel Bars and ShapesA 366/A 366M Specification for Commercial Steel (CS)Sheet, Carbon (0.15 Maximum Percent) Cold-Rolled3A 513 Specification for Electric-Resistance-Welded Carbonand Alloy Steel Mechanical TubingA 563 Specification for Carbon and Alloy Steel NutsB 3
5、6/B 36M Specification for Brass Plate, Sheet, Strip, andRolled BarB 124/B 124M Specification for Copper and Copper AlloyForging Rod, Bar, and ShapesB 176 Specification for Copper-Alloy Die Castings2.2 ANSI Standards:4B18.1.1 Small Solid RivetsB18.6.3 Slotted and Recessed Head Machine Screws andMachi
6、ne Screw NutsB18.21.1 Lock WashersB27.2 Plain Washers2.3 Other Documents:ABS Rules for Building and Classing Steel Vessels5SSPC Specification 66AWS D1.1 Welding Code73. Classification3.1 Emergency gear lockers shall be classified in four typesas follows:3.1.1 Type 1For stowage of one complete firema
7、ns outfit,conforming to all requirements of all sections, figures, anddetails of this specification.3.1.2 Type 2For stowage of two complete firemensoutfits, conforming to all requirements of all sections, figures,and details of this specification.3.1.3 Type 3For stowage of one complete firemans outf
8、it,with locker dimensions in accordance with Figs. 2, 3, and 4(dimensions only), and conforming to the requirements of 3.2,3.3, 4.1, 5.2.4, and Sections 6 and 7 inclusive.3.1.4 Type 4For stowage of two complete firemensoutfits, with locker dimensions in accordance with Figs. 2, 3,and 4 (dimensions o
9、nly), and conforming to the requirementsof 3.2, 3.3, 4.1, 5.2.4, and Sections 6 and 7 inclusive.3.2 One complete firemans outfit shall consist of thefollowing emergency gear (not included in this specification):3.2.1 Self-contained breathing apparatus (24 by 14 by 11 in.(610 by 355 by 280 mm).3.2.2
10、Recharge air tank (7-in. (180-mm) diameter by 22 in.(560 mm) long).3.2.3 Set protective clothing, including helmet, gloves, andboots.3.2.4 Lifeline (150 ft (45 m), 18 by 18 by 10 in. (455 by 455by 255 mm).3.2.5 Three-cell, explosion-proof flashlight with spare cells.3.2.6 Flame safety lamp.3.2.7 Fir
11、e axe.3.3 In addition to the equipment listed in 3.2, each lockershall contain space for the following (not part of this specifi-cation):3.3.1 First-aid kit, (1), (10 by 10 by 7 in. (255 by 255 by 180mm).3.3.2 Spare air tanks, as space allows (see Figs. 2, 3, and 4).1This specification is under the
12、jurisdiction of ASTM Committee F25 on Shipsand Marine Technology and is the direct responsibility of Subcommittee F25.03 onOutfitting and Deck Machinery.Current edition approved Nov. 1, 2004. Published November 2004. Originallyapproved in 1986. Last previous edition approved in 1999 as F 1018 87a (1
13、999)e1.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Withdrawn.4Available from American National Standards
14、 Institute (ANSI), 25 W. 43rd St.,4th Floor, New York, NY 10036.5Available from American Bureau of Shipping (ABS), ABS Plaza, 16855Northchase Dr., Houston, TX 77060.6Available from Society for Protective Coatings (SSPC), 40 24th St., 6th Floor,Pittsburgh, PA 15222-4656.7Available from The American W
15、elding Society (AWS), 550 NW LeJeune Rd.,Miami, FL 33126.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.4. Ordering Information4.1 Order using this ASTM designation, year of issue,locker type, and finish.5. Materials and Manufacture
16、5.1 MaterialsMaterials shall be as specified in Table 1.5.2 Manufacture:5.2.1 Mandatory dimensions and construction details forTypes 1 and 2 are as depicted in Figs. 1-9.5.2.2 Mandatory dimensions for Types 3 and 4 are as shownin Fig. 2, Fig. 3, and Fig. 5, respectively, and applicable detailsof Sec
17、tions “A-A and “B-B. Alternative construction detailsare permissible.5.2.3 Construction details depicted in Figs. 4-9, while spe-cifically referring to locker Type 2, shall be adapted to suitlocker Type 1.5.2.4 Welded construction, in accordance with ABS Rulesfor Building and Classing Steel Vessels
18、or AWS D 1.1Structural Welding Code shall be used throughout, unlessotherwise specified.6. Dimensions and Tolerances6.1 Dimensions are as indicated.6.2 Tolerance6116 in. (1.5 mm).7. Workmanship, Finish, and Appearance7.1 Entire assembly shall be free of weld spatter, slag,splinters, sharp edges, bur
19、rs, projections, and other defects thatmay be hazardous to personnel.7.2 The locker shall be cleaned after assembly to a com-mercial finish in accordance with SSPC-SP6.7.3 Unless otherwise required by the ordering documents,the unit shall have the manufacturers standard baked-onenamel finish.7.3.1 T
20、he color shall be specified in the ordering documents.8. Keywords8.1 emergency gear; firemans locker; firemans outfit;locker; steel locker; stowage lockerF 1018 87a (2004)2TABLE 1 Parts List for Locker Type 2NOTE 11 in. = 25.4 mm.DescriptionItemNumberQuantityASTM, ANSIDocumentsLocker top sheet, 16 g
21、age 3 39 in. long 3 30 in. wide, carbon steel 1 1 A 366/A 366MLocker side, right sheet, 16 gage 3 72 in. long 3 2958 in. wide, carbonsteel2 1 A 366/A 366MLocker side, left sheet, 16 gage 3 72 in. long 3 2958 in. wide, carbonsteel3 1 A 366/A 366MLocker back sheet, 16 gage 3 72 in. long 3 39 in. wide,
22、 carbonsteel4 1 A 366/A 366MLocker bottom sheet, 16 gage 3 42 in. long 3 31 in. wide, carbon steel 5 1 A 366/A 366MDoor, right sheet, 16 gage 3 73 in. long 3 25 in. wide, carbon steel 6 1 A 366/A 366MDoor, left sheet, 16 gage 3 73 in. long 3 23 in. wide, carbon steel 7 1 A 366/A 366MShelf, full-widt
23、h sheet, 16 gage 3 40 in. long 3 26 in. wide, carbon steel 8 2 A 366/A 366MShelf, half-width sheet, 16 gage 3 26 in. long 3 21 in. wide, carbon steel 9 2 A 366/A 366MPartition, vertical sheet, 16 gage 3 52 in. long 3 25 in. wide, carbon steel 10 1 A 366/A 366MCorner bracket sheet, 16 gage 3 5 in. lo
24、ng 3 334 in. wide, carbonsteel11 4 A 366/A 366MLever handle, rightdoorcast brass 12 1 B 176 (UNS C 86500)Keeper brass 13 1 B 124/B 124M (UNS C 67500)Machine screw oval-head, #10-24 UNC-2A 3 length to suit brass 14 14 ANSI B18.6.3B 124/B 124M (UNS C 67500)Nut hexagon machine, #10-24 UNC-2B 15 14 ANSI
25、 B18.6.3brass B 124/B 124M (UNS C 67500)Escutcheon sheet, 16 gage 3 2 in. long 3 138 in. wide, brass 16 1 B 36/B 36MLocking rod, upper round bar,516-in. diameter 3 37 in. long, carbon steel 17 1 A 36/A 36MLock rod, lower round bar,516-in. diameter 3 37 in. long, carbon steel 18 1 A 36/A 36MGuide, lo
26、cking rod tube, -in. outside diameter 3 0.065-in. wall thickness 3118-in. long, carbon steel19 2 A 513Latch sheet, 12 gage 3 31116 in. long 3 2 in. wide, carbonsteel20 1 A 366/A 366MReinforcing, latch sheet, 16 gage 3 5 in. long 3 134 in. wide, carbon steel 21 1 A 366/A 366MLock washer38-in. nominal
27、 size, carbon steel 22 1 ANSI B18.21.1Rivet brazier head,532-in. diameter 23 2 ANSI B18.1.1Rivet flathead,316-in. diameter 24 2 ANSI B 18.1.1Insulation wool felt,364 in. thick 3 2 in. long 3 138 in. wide 25 1Reinforcing clip sheet, 12 gage 3 1 in. square, carbon steel 26 1 A 366/A 366MReinforcing cl
28、ip sheet, 16 gage 3 1 in. square, carbon steel 27 1 A 366/A 366MCam sheet, 12 gage 3 178 in. square, carbon steel 28 1 A 366/A 366MLatch filler sheet, 16 gage 3 278 in. long 3 2 in. wide, carbonsteel29 1 A 366/A 366MStrap sheet, 16 gage 3 2 in. long 3 1 in. wide, carbon steel 30 1 A 366/A 366MNut he
29、xagon,38-16 UNC-2B, carbon steel 31 1 A 563Liner sheet, 16 gage 3 1 in. long 3 118 in. wide, carbonsteel32 1 A 366/A 366MHinge sheet, 16 gage 3 3 in. long 3 1 in. wide, carbon steelincluded:316-in. diameter 3 1-in. long stainless steelpin33 6 A 366/A 366MA 276Lock washer316-in. nominal size,716-in.
30、outside diameter, carbonsteel34 12 ANSI B18.21.1Liner, hinge sheet, 16 gage 3 2 in. long 334 in. wide, carbon steel 35 6 A 366/A 366MLeg angle, 1 3 1 318 3 6 in. long, carbon steel 36 4 A 36/A 36MFoot pad sheet, 10 gage 3 1 in. square, carbon steel 37 4 A 366/A 366MLeg bracket sheet, 10 gage 3 8 in.
31、 long 3 3 in. wide, carbon steel 38 4 A 366/A 366MLeg reinforcement sheet, 10 gage 3 8 in. long 3 134 in. widebend toform78- 378-in. angle, carbon steel39 4 A 366/A 366MMachine screw -2OUNC-2A 334 in. long, carbon steel 40 16 ANSI B18.6.3Nut hexagon machine, -2OUNC-2B, carbon steel 41 16 ANSI B18.6.
32、3Lock washer -in. nominal size, carbon steel 42 16 ANSI B18.21.1F 1018 87a (2004)3NOTE 11 in. = 25.4 mm.NOTE 2Approximately 2-in. high red lettering typical.FIG. 1 Emergency Gear Stowage LockerType 1F 1018 87a (2004)4NOTE 11 in. = 25.4 mm.NOTE 2Approximately 2-in. high red lettering typical.FIG. 2 E
33、mergency Gear Stowage LockerTypes 2, 3, and 4F 1018 87a (2004)5FIG. 3 Emergency Gear Stowage LockerTypes 2, 3, and 4 (Section “A-A”)F 1018 87a (2004)6NOTE 11 in. = 25.4 mm.FIG. 4 CornerF 1018 87a (2004)7NOTE 11 in. = 25.4 mm.FIG. 5 Lock BoltF 1018 87a (2004)8NOTE 11 in. = 25.4 mm.FIG. 6 Locking Hand
34、leF 1018 87a (2004)9NOTE 11 in. = 25.4 mm.FIG. 7 LatchMiscellaneous DetailsF 1018 87a (2004)10NOTE 11 in. = 25.4 mm.FIG. 8 LegF 1018 87a (2004)11NOTE 11 in. = 25.4 mm.FIG. 9 Hinge and LinerASTM International takes no position respecting the validity of any patent rights asserted in connection with a
35、ny item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technica
36、l committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration
37、at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor
38、 Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).F 1018 87a (2004)12
