1、Designation: F1062 97 (Reapproved 2018)Standard Test Method forVerification of Ski Binding Test Devices1This standard is issued under the fixed designation F1062; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last rev
2、ision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method defines procedures to determine agree-ment between a standard apparatus for measuring the releasemoments of s
3、ki bindings and a test device of unspecifieddesign.1.2 This test method also covers procedures for checkingagreement between individual devices of identical but unspeci-fied design, intended for determining the release moments ofski bindings.1.3 Values expressed in newton meters, newtons, and cen-ti
4、meters are to be regarded as the standard.1.4 Values expressed in units of torque may be converted tothe appropriate force values when devices which indicate forceare used.1.5 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibilit
5、y of the user of this standard to establish appro-priate safety, health, and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accor-dance with internationally recognized principles on standard-ization est
6、ablished in the Decision on Principles for theDevelopment of International Standards, Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:2E4 Practices for Force Verification of Testing MachinesE29 Pr
7、actice for Using Significant Digits in Test Data toDetermine Conformance with SpecificationsE74 Practices for Calibration and Verification for Force-Measuring InstrumentsE456 Terminology Relating to Quality and StatisticsF504 Test Method for Measuring the Quasi-Static ReleaseMoments of Alpine Ski Bi
8、ndingsF1061 Specification for Ski Binding Test DevicesF1063 Practice for Functional Inspections and Adjustmentsof Alpine Ski/Binding/Boot SystemsF1064 Practice for Sampling and Inspection of Completeand Incomplete Alpine Ski/Binding/Boot Systems inRental Applications3. Terminology3.1 DefinitionsThe
9、terms and abbreviations used in thisdocument are defined in accordance with Test Method F504,Specification F1061, Terminology E456, Practices E4, andPractice E74.3.2 Definitions of Terms Specific to This Standard:3.2.1 adifference between the calibration of the specificdevice tested for agreement wi
10、th an instrument of the typedescribed in Test Method F504 and the calibration of anindividual device of the same design.3.2.2 dagreement between the test device and the standardapparatus described in Test Method F504 and Section 9 of thistest method.3.2.3 rimprecision of the device tested.3.2.4 oper
11、ating range (OR)the portion of the full range ofthe device which may be employed in accordance withPractices F1063 and F1064. OR shall be defined by the user inaccordance with the Inspection section of Annex 2 of PracticesF1063 and F1064.3.2.5 recommended operating range (ROR)the portion ofthe full
12、range of the test device that is in accordance withProposed Specification P 193.3.2.6 reference bindinga binding or group of bindingsused in the verification of a test device.3.2.7 standard apparatuslaboratory equipment includinga test frame and instrumentation used as the basis for compari-son with
13、 the test device.3.2.8 test devicea machine for determining the releasemoments of ski/boot/binding systems.3.3 Symbols:1This test method is under the jurisdiction of ASTM Committee F27 on Snowand Water Sports and is the direct responsibility of Subcommittee F27.10 onBinding Test Procedures.Current e
14、dition approved July 1, 2018. Published August 2018. Originallyapproved in 1988. Last previous edition approved in 2013 as F1062 97 (2013).DOI: 10.1520/F1062-97R18.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Boo
15、k of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with internationally recogni
16、zed principles on standardization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.13.3.1 Mz a moment in a horizontal plane as shown in thefigure in T
17、est Method F504, which illustrates terminologyrelating to the boot/ski system.3.3.2 My a moment in a vertical plane with the ski asshown in the figure in Test Method F504, which illustratesterminology relating to the boot/ski system.4. Significance and Use4.1 Results obtained by this test method can
18、 be used todetermine the suitability of specific test device designs inmeasuring the release moments of ski/boot/binding systems.4.2 This test method provides a means by which manufac-turers of test devices and manufacturers of releasable skibindings can provide compatible instructions to facilities
19、 whichperform the final inspection of the complete boot/binding/skisystem prior to use.4.3 This test method is not appropriate for determiningprecision between operators.5. Apparatus5.1 Test SkiThe test ski shall meet the stiff ski definition inthe portion of the Apparatus Section of Test Method F50
20、4pertaining to skis and bindings.5.2 Test SoleThe test sole shall meet the requirements inthe portion of the Apparatus Section of Test Method F504pertaining to boots, and shall be of a design compatible withthe reference binding. The test sole may be modified toestablish necessary interfaces with th
21、e standard apparatus andtest device providing such modifications do not influence theproper function of the reference binding.5.3 Test Frame and Instrumentation:5.3.1 All apparatus shall meet the portions of the ApparatusSection of Test Method F504 pertaining to cable,instrumentation, and load appli
22、cation.5.3.2 Devices shall be employed to monitor cable tension.Differences of more than 5 % in cable tension at the attachmentpoints with the ski may significantly bias results.5.4 Reference BindingThe reference binding shall be ofthe type specified by the manufacturer of the test device.6. Prepara
23、tion of Apparatus6.1 Mount the reference binding on the test ski and fit to thetest sole in accordance with the specification of the bindingmanufacturer.6.2 Lubricate all interfaces within the reference binding andall areas of sliding contact between test sole and binding witha compatible grease.6.3
24、 Calibrate the binding in tests 1.1 and 2.1 (and 2.2 ifappropriate) of Test Method F504, using the standard appara-tus.6.3.1 The calibration of the reference binding shall be asspecified by the test device manufacturer.NOTE 1Practices E4 and Practice E74 may be used as general guidesin developing ca
25、libration procedures.6.4 Condition the binding prior to each test series bycausing the mechanism to release three times in the appropriatedirection.7. Conditioning7.1 Unless the test device is to be used at other than normalroom temperatures, conduct all tests at a temperature of 23 65C and a relati
26、ve humidity of 50 6 5 %. Do not varytemperature over the course of the test by more than 2C andhumidity by more than 5 %.8. Procedure8.1 Perform five repetitions of the following procedure:8.1.1 Using the standard apparatus, perform three repeti-tions of a test required for Type I, II, or III device
27、s, and performthree repetitions of the analogous test on the test device.8.1.1.1 Randomly select which series of three tests will beconducted first.8.1.1.2 From the Table on Load Application of Test MethodF504, use tests 1.1 and 1.2 for Type I devices, tests 2.1 and 2.2(if appropriate) for Type II d
28、evices and tests as specified by thetest device manufacturer for Type III devices.8.1.1.3 Follow the test device manufacturers instructionsfor conducting analogous tests.8.2 Perform the procedure in 8.1 8.1.1.3 at the beginning,middle, and end of the ROR. If the reference binding cannot beadjusted f
29、or release over the full ROR, perform the test(s) at 10or 90 % of the limit(s) of the reference binding as appropriate.8.2.1 Immediately before and after each cycle of 8.1 8.1.1.3, measure and record the calibration of the test device, inaccordance with the method specified by the test devicemanufac
30、turer. Use a dead weight or instrument which isaccurate to within 1 %.NOTE 2Practice E74 may be used as a general guide for selectingcalibration devices.8.2.1.1 Check the calibration of the test device at bothextremes and the middle of the ROR and at 10 and 90 % of fullscale unless such values fall
31、within the ROR.8.3 Repeat the steps given in 8.2 for all appropriate testslisted in 8.1.1.2.8.4 Make and record all readings to a resolution of one halfthe smallest scale division of the test device unless otherwisespecified in the operating instructions for the test device. Readthe data recorded by
32、 the standard apparatus to a significance of2 % of the lower limit of the ROR.9. Calculation9.1 Determine the middle quantitative value (median) ofeach test series (three repetitions of each test constitute aseries) and use it for all calculations.9.2 Calculate the mean and standard deviations for t
33、he testdevice and the standard apparatus in each cycle of 8.1.9.2.1 Calculate the standard deviation, in percent, as fol-lows:s 50.43RX3100F1062 97 (2018)2where:X= mean, andR = range of observations.9.3 Calculate d for each cycle of 8.1, in percent, as follows:d 5Xtd2 XsaXsawhere:sa = standard appar
34、atus, andtd = test device.9.4 Calculate r for each cycle of 8.1, in percent, as follows:r 5 =ssa22 Std2if Ssa.Std, then r 5 09.5 Plot a calibration curve for each cycle of 8.3 in terms ofthe data recorded in 8.2.1. By the least squares method, fit asecond order polynomial equation to the data.10. Re
35、port10.1 Prepare a clear and complete report of each verificationof a test device including:10.1.1 Name of the calibrating agency,10.1.2 Date of verification,10.1.3 Test device description and serial number,10.1.4 Reference binding,10.1.5 Temperature at which tests were conducted.10.1.6 ROR, d, and
36、r for all test series listed by test method,and the point in the ROR, (lower, middle, or upper), and10.1.7 All calibration curves and their equations.11. Precision and Bias11.1 Repeatability and reproducibility will be determined.11.2 The bias of this test method has not been determined.ANNEX(Mandat
37、ory Information)A1. CALIBRATION OF SKI BINDING TEST DEVICESA1.1 ScopeA1.1.1 This test method covers procedures for checkingagreement between individual devices of identical but unspeci-fied design, intended for determining the release moments ofski bindings.A1.2 ProcedureA1.2.1 From the calibration
38、curves, determine the loadswhich correspond to the lower and upper limits and middle ofthe ROR.NOTE A1.1Averaging calibration curves derived for positive andnegative moments may be appropriate.A1.2.2 By the method employed in 8.2.1 and using theloads determined in A1.2.1, check the calibration of th
39、e testdevice and record the values indicated by the specific device ateach test point in the ROR.A1.3 CalculationA1.3.1 For upper, middle, and lower test points, calculatethe difference, in percent, of a between the moment derivedfrom the calibration curve and the moment indicated by the testdevice,
40、 using the following equation:a 5Md2 MtMt3100where:Md= moment indicated by the test device, andMt= moment derived from the calibration curve.A1.4 ReportA1.4.1 Prepare a clear and complete report of the calibrationof each test device including:A1.4.1.1 Name of calibrating agency,A1.4.1.2 Date of cali
41、bration,A1.4.1.3 Test device description, serial number, andlocation,A1.4.1.4 Test loads, test points and calibration method, andA1.4.1.5 ROR, and al,am,aufor each classification,where:l = lower,m = middle, andu = upper.F1062 97 (2018)3ASTM International takes no position respecting the validity of
42、any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to r
43、evision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Yo
44、ur comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is cop
45、yrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 97 (2018)4
