1、Designation: F1071 94 (Reapproved 2012) An American National StandardStandard Specification forExpanded-Metal Bulkhead Panels1This standard is issued under the fixed designation F1071; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision
2、, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers steel expanded-metal bulkheadpanels suitable for use in storerooms, shops, and
3、 as protectionagainst personnel hazards.1.2 The values stated in inch-pound units are to be regardedas the standard. The values given in parentheses are forinformation only.2. Referenced Documents2.1 ASTM Standards:2A36/A36M Specification for Carbon Structural SteelD3951 Practice for Commercial Pack
4、aging2.2 Other Documents:ABS Rules for Building and Classing Steel Vessels3AWS D1.1 Structural Welding Code43. Classification3.1 Bulkhead panels are furnished in three types as follows.3.1.1 Type IUniversal bulkhead panels for use as either aright-hand or left-hand panel.3.1.2 Type IIRight-hand bulk
5、head panel.3.1.3 Type IIILeft-hand bulkhead panel.3.2 Bulkhead panels are furnished in two classes as follows.3.2.1 Class ABulkhead panels, 2 ft (610 cm).3.2.2 Class BBulkhead panels, 3 ft (915 cm).3.3 Bulkhead panels Types II and III, Class A only, arefurnished in three sizes as follows.3.3.1 Size
6、176 in. (195 cm) high.3.3.2 Size 264 in. (165 cm) high.3.3.3 Size 340 in. (100 cm) high.4. Ordering Information4.1 Orders for expanded-metal panels under this specifica-tion shall include this specification number, type, class, andsize.5. Materials and Manufacture5.1 MaterialsSee Table 1.5.2 Manufac
7、ture:5.2.1 Welding shall be in accordance with AWS D1.1 or theABS Rules for Building and Classing Steel Vessels.5.2.2 Panels shall be welded and fabricated as shown inFigs. 1-6.5.2.3 After panels have been shipped to the contractor, thepanels will be assembled into bulkheads by welding or boltingby
8、others.6. Tolerances6.1 Tolerances6116 in. (1.5 mm).7. Workmanship, Finish, and Appearance7.1 Expanded-metal panels shall be free from all cracks,burrs, sharp edges, and other defects.7.2 The panel manufacturer shall apply a nonhazardouscorrosion-inhibiting primer coating to all panel assemblies.8.
9、Packaging and Package Marking8.1 Expanded-metal bulkhead panels shall be individuallypacked for shipment and storage in accordance with PracticeD3951.8.2 In addition to any special marking required by thecontract or purchase order, each expanded-metal panel packageshall be marked in accordance with
10、Practice D3951.9. Keywords9.1 bulkhead panels; expanded-metal bulkhead panels; pan-els; steel bulkhead panels1This specification is under the jurisdiction of ASTM Committee F25 on Shipsand Marine Technology and is the direct responsibility of Subcommittee F25.03 onOutfitting and Deck Machinery.Curre
11、nt edition approved June 1, 2012. Published October 2012. Originallyapproved in 1987. Last previous edition approved in 2006 as F1071 94 (2006).DOI: 10.1520/F1071-94R12.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annua
12、l Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from the American Bureau of Shipping, ABS Plaza, 16855 North-chase Dr., Houston, TX 77060.4Available from American Welding Society, 550 N.W. Le Jeune Rd., Miami, FL33126.Copyright A
13、STM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1TABLE 1 Expanded-Metal Bulkhead Panel MaterialsNOTE 11 in. = 25.4 mm.ItemNumberDescription1 Frame angle, 1 1in.,Specification A36/A36M2 Braceflatbar,2in.,Specification A36/A36M3 Expanded metal 13-g
14、age thick -in. flat pattern 23 in. wide, Specification A36/A36M4 Expanded metal 13-gage thick -in. flat pattern 35 in. wide, Specification A36/A36MNOTE 11 in. = 25.4 mm.FIG. 1 Expanded-Metal Bulkhead PanelType 1, Class A, Size 1F1071 94 (2012)2NOTE 11 in. = 25.4 mm.FIG. 2 Expanded-Metal Bulkhead Pan
15、elType I, Class B, Size 1NOTE 1Type IIILeft hand not shown.NOTE 21 in. = 25.4 mm.FIG. 3 Expanded-Metal Bulkhead PanelType II, Class A, Size 1NOTE 1Type IIILeft hand not shown.NOTE 21 in. = 25.4 mm.FIG. 4 Expanded-Metal Bulkhead PanelType II, Class B, Size 1F1071 94 (2012)3ASTM International takes no
16、 position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own respons
17、ibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed t
18、o ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the add
19、ress shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone),
20、 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).NOTE 11 in. = 25.4 mm.FIG. 5 Expanded-Metal Bulkhead PanelType II, Class A, Size 2NOTE 11 in. = 25.4 mm.FIG. 6 Expanded-Metal Bulkhead PanelType II, Class A, Size 3F1071 94 (2012)4
