1、Designation: F 1122 04An American National StandardStandard Specification forQuick Disconnect Couplings (6 in. NPS and Smaller)1This standard is issued under the fixed designation F 1122; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revis
2、ion, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers the manufacturing data re-quired to produce a variety of styles and sizes
3、of quickdisconnect couplings up to and including NPS 6 for marine usethat ensure interchangeability and safety of operation.1.2 In general, quick disconnect couplings are hose and pipeend fittings that permit quick mechanical attachment by meansother than bolted or threaded fittings. The method of a
4、ttach-ment is a male coupling half (adapter) that fits into a femalecoupling half (coupler) of the same size. By closing attachedcam handles, the coupling halves seal, permitting fluids to betransported under pressure through the quick disconnect cou-pling.1.3 The values stated in this specification
5、 are in inch-poundunits with SI units given in parentheses. The values of eachsystem may not be exact equivalents. Therefore, each systemshould be considered separately.1.4 The following safety hazards caveat pertains only to thetest method described in this specification: This standard doesnot purp
6、ort to address all of the safety concerns, if any,associated with its use. It is the responsibility of the user of thisstandard to establish appropriate safety and health practicesand determine the applicability of regulatory limitations priorto use.2. Referenced Documents2.1 ANSI Standards:2B2.1 Pi
7、pe ThreadsB16.5 Pipe Flanges and Flanged Fittings, Steel-Nickel Al-loy, and Other Special AlloysB16.24 Bronze Pipe Flanges and Flanged FittingsB16.42 Ductile Iron Pipe Flanges and Flanged FittingsB31.1 Power Piping Code2.2 MSS Standards:3MSS-SP-6 Standard Finish for Contact Faces of PipeFlanges and
8、Connecting End Flanges of Valves andFittingsMSS-SP-25 Standard Marking System for Valves, Fittings,Flanges, and UnionsMSS-SP-55 Quality Standard for Steel Castings for Valves,Flanges, and Fittings and Other Piping Components (Vi-sual Method)2.3 ASME Standards:4Section VIII, Division 1, Pressure Vess
9、elsSection IX, Welding and Brazing Qualifications3. Definitions of Terms Specific to This Standard3.1 adapterone half of a quick disconnect coupling thatfits into the coupler and seals against an elastomer gasketpositioned inside the coupler.3.2 cam handleshandles that are assembled to the couplerha
10、lf which by closing engages the adapter sealing the coupling.3.3 couplerone half of a quick disconnect coupling thatreceives the adapter. This half contains the sealing gasket andcam handles (see Fig. 1).NOTE 1See Fig. 2 for a description of typical coupler pipe fittings.4. Classification4.1 Quick d
11、isconnect couplings shall consist of the follow-ing types:4.1.1 Standard ClassThis type is to be designed for a 4:1burst factor of safety.4.1.2 Class IThis type is to be designed for a 5:1 burstfactor of safety.4.2 Both Standard Class and Class I will be called quickdisconnect couplings in the body
12、of this specification unlessotherwise specified.5. Ordering Information5.1 Purchase orders for quick disconnect couplings underthis specification shall include the following applicable infor-mation:5.1.1 Class.1This specification is under the jurisdiction of ASTM Committee F25 on Shipsand Marine Tec
13、hnology and is the direct responsibility of Subcommittee F25.11 onMachinery and Piping Systems.Current edition approved Nov. 1, 2004. Published November 2004. Originallyapproved in 1987. Last previous edition approved in 1998 as F 1122 87 (1998).2Available from American National Standards Institute
14、(ANSI), 25 W. 43rd St.,4th Floor, New York, NY 10036.3Available from Manufacturers Standardization Society of the Valve and FittingsIndustry (MSS), 127 Park St., NE, Vienna, VA 22180-4602.4Available from American Society of Mechanical Engineers (ASME), ASMEInternational Headquarters, Three Park Ave.
15、, New York, NY 10016-5990.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.5.1.2 Size and type of each coupling half-end connection.(Example: 2- by 112-in. NPT).5.1.3 ASTM material designation and date including alloyspecifications fo
16、r the following:5.1.3.1 Adapter and coupler halves,5.1.3.2 Cam handle, and5.1.3.3 Cam handle pivot pin.5.1.4 Product or fluid in applicable system.5.1.5 Shipping instructions.5.1.6 Any special requirements, such as testing, coatings,and threads.6. Materials and Manufacture6.1 Materials:6.1.1 Pressur
17、e-retaining parts shall be manufactured frommaterial specifications and grades listed in Section VIII,Division 1, of the ASME Boiler and Pressure Vessel Code orANSI B31.1.6.1.2 All other materials of construction shall be of the typespecified by the user and shall conform to ASTM, ASME, orMetal Powe
18、r Industry Federation material specifications. Ma-terials not identified by the ordering data shall be of themanufacturers standard and of the same quality used for theintended purpose in commercial practice.6.1.3 All material incorporated in the work covered by thisspecification shall be new. The u
19、se of rebuilt or used productsare not allowed under this specification.6.1.4 Gaskets are to be produced from a compressibleelastomeric material and shall be compatible with the fluid tobe transferred (see 5.1.4).6.2 Manufacture:6.2.1 Adapters and couplers are to be produced as castingsor forgings. C
20、am handles may be produced by casting, forging,or sintered metal processes. Established commercial process-ing methods are to be used to produce these parts, providedchemical and physical properties are consistent with thosecataloged for the specified materials.6.2.2 Pipe threads on the service end
21、of couplers or adapt-ers, when specified, shall meet ANSI B2.1.6.2.3 Flanges on the service end of couplers or adapters,when specified, shall meet ANSI B16.5, B16.24,orB16.42.6.2.4 Flanges shall be finish machined to specificationsshown in MSS-SP-6.6.2.5 Cam handles assembled to the coupler are to h
22、ave asafety locking device to ensure against the handles beingopened unintentionally or vibrating open. This locking devicemust require a separate, deliberate effort in the openingoperation over the standard handle operation.6.2.6 Cam handles shall be manufactured to contain theadapter within the co
23、upler under rated pressure with no leakageoccurring. The cam action shall not distort the couplersrendering the coupler unusable. The force required to close thecam handles shall be adequate to prevent leakage, but shall beeasily attainable through hand operation by an average strengthperson. Handle
24、s should not need to be hammered closed.FIG. 1 Typical Coupler AssemblyFIG. 2 Adapter/Coupler Types (End Dimensional Data Located inTables Indicated by Arrows)F11220426.2.7 Welding procedure qualifications, welder performancequalifications, and welding materials shall be in accordancewith ANSI B 31.
25、1 and Section IX of the ASME Code. Brazingor soldering shall not be used. Where radiography is required(see 12.1), all welds shall be butt welds.7. Other Requirements7.1 All couplings shall have a maximum allowable workingpressure of not less than 150 psi (1034 kPa).7.2 Maximum allowable working pre
26、ssure (MAWP) for aStandard Class coupling shall be 25 % of its burst pressure.7.3 Maximum allowable working pressure for a Class Icoupling shall be 20 % of its burst pressure.7.4 Burst pressure shall be determined in accordance withSection VIII, Division 1 of the ASME Code.8. Dimensions8.1 The dimen
27、sions and tolerances required to ensure inter-changeability of adapter and coupler halves, of common sizes,shall be as given in Figs. 3-15.8.2 Sizes as listed in the tables correspond to NPS for pipingsystems.9. Workmanship, Finish, and Appearance9.1 Couplings are to be produced with quality workman
28、-ship. Casting surface quality is to be in accordance withMSS-SP-55. Machined surfaces are to be finish machined to a125-in. (3175-mm) (AA) finish or better with no porosityshowing.9.1.1 Couplings are to be free of burrs or sharp edges.Machined surfaces are to be free of nicks or scratches that maya
29、ffect the sealing capabilities of the couplings.9.1.2 Surfaces are to be sound with good appearance andtrue pattern. Internal surfaces, if not machined, shall besmooth, as expected from good quality casting, and free fromany flaw that would render the part unsafe for its intended use.9.2 Cam handles
30、 are to be smooth, having no burrs or sharpedges. Cam closing surface is to be continuous, providing anincreasing axial pull on mating adapter until proper seatingagainst the gasket occurs.9.3 Defective parts are not to be repaired by welding,brazing, or any other method, to fill porosity or other f
31、laws inthe casting.NOTE 1Unidentified tolerances; fractional = 6164 (60.4), decimal = +0.000/0.005 (+0.000/0.127), angular = 62 (60.035 rad)SizeDimensions, in. (mm)ABCDEFGHJ121.264(32.1)1.035(26.3)1732(31)2732(21)0.471(12)1(25.4)0.378(9.6)116(1.6)332(2.4)341.264(32.1)1.035(26.3)1732(31)3132(24.6)0.4
32、71(12)1(25.4)0.378(9.6)116(1.6)332(2.4)11.446(36.7)1.144(29)138(34.9)1332(27.8)0.565(14.3)1516(33.3)0.378(9.6)332(2.4)332(2.4)1141.792(45.5)1.388(35.2)12332(43.6)114(31.7)0.690(17.5)1916(39.7)0.441(11.2)18(3)18(3)1122.105(53.4)1.690(42.9)2132(51.6)1916(39.7)0.690(17.5)158(41.3)0.441(11.2)18(3)18(3)2
33、2.484(63.1)2.065(52.4)21332(61.1)11516(49.2)0.848(21.5)178(47.6)0.441(11.2)18(3)18(3)2122.985(75.8)2.545(64.6)278(73)2716(61.9)0.848(21.5)11516(49.2)0.441(11.2)18(3)532(4)33.604(91.5)3.202(81.3)312(88.9)3332(78.6)0.895(22.7)2(50.8)0.503(12.8)18(3)532(4)44.708(119.6)4.307(109.4)41932(116.7)418(104.8)
34、0.895(22.7)2116(52.4)0.503(12.8)18(3)732(5.6)55.728(145.5)5.312(134.9)558(142.9)518(130.2)0.897(22.8)218(54)0.503(12.8)18(3)732(5.6)66.929(176)6.362(161.6)61316(173)6532(156.4)0.963(24.5)214(57.1)0.659(16.7)18(3)732(5.6)FIG. 3 Adapter End DimensionsF11220439.4 Gaskets are to be produced having paral
35、lel sealing faces.Faces are not to contain any imperfections that will allowleakage to occur at working pressure.10. Number of Tests10.1 A prototype coupling of each size of each particulardesign shall be tested to determine conformance to thisspecification.10.2 Each coupling shall be tested as outl
36、ined in productiontesting of 11.2.11. Test Methods11.1 Prototype testing of each size of each particular designshall be as follows. Maintain the indicated test pressures for atleast 1 min without leakage.11.1.1 Pressure test to twice the MAWP after having beencycled (connected, closed, opened, and d
37、isconnected) threetimes.11.1.2 Pressure test at MAWP while applying a moment of1000 in.-lbs (113 NM) to one coupling half attempting to twistit loose. Reapply MAWP after the moment is removed.11.2 Production TestHydrostatically test each coupling to1.5 times MAWP.11.3 The test apparatus for 11.2 is
38、to be a state-of-the-artdevice, designed to apply internal pressure to the couplinghalves with gasket in place. Dye the fluid used to apply thehydrostatic pressure to facilitate observation of leakage shouldleakage occur.12. Inspection12.1 Nondestructive examination of welds shall be per-formed as r
39、equired by ANSI B31.1. Additionally, 100 %radiography of all welds is required for couplings equal to orgreater than 4-in. (100-mm) nominal diameter and when thenominal wall thickness is greater than 0.375 in. (9.4 mm).12.2 The manufacturer is responsible for the inspection andtesting of each coupli
40、ng and assuring conformity to thisspecification. Samples selected for inspection, at least onecoupling from each lot of 100 or fraction thereof, are to bedimensionally checked 100 % to verify adherence to thisspecification. Couplings having threads are to be inspectedusing proper thread gages. The e
41、ntire lot of couplings is to beNOTE 1Unidentified tolerances; fractional = 6164 (60.4), angular = 62 (60.035 rad), decimal = 60.005 (60.127)SizeDimensions, in. (mm)ABCDEF121.274(32.3)14(6.3)12764(36.1)332(2.4) . .341.274(32.3)14(6.3)12764(36.1)332(2.4) . .11.464(37.2)932(7.1)11932(40.5)332(2.4) . .1
42、141.810(46)932(7.1)2(50.8)18(3) . .1122.123(53.9)932(7.1)214(57.1)18(3) . .22.508(63.7)932(7.1)21116(68.3)18(3) . .2123.009(76.4)932(7.1)3316(81)532(4) . .33.628(92.1)932(7.1)32532(96)532(4) . .44.732(120.2)932(7.1)41516(125.4)732(5.6)332(2.4)32932(99.2)55.752(146.1)932(7.1)53132(151.6)732(5.6)332(2
43、.4)45164(121.8)66.948(176.5)932(7.1)7964(181.4)732(5.6)332(2.4)52932(150)FIG. 4 Coupler End DimensionsF1122044visually checked for porosity and other flaws that couldadversely affect usability of this product.12.3 The manufacturer shall afford the purchasers inspectorall reasonable facilities necess
44、ary to satisfy him that thematerial is being furnished in accordance with this specifica-tion. Inspection by the purchaser shall not interfere unneces-sarily with the manufacturers operations. All examinationsand inspections shall be made at the place of manufacture,unless otherwise agreed upon.12.4
45、 Other tests, when agreed upon, shall be made frommaterial of the lots covered in the order.13. Certification13.1 When specified in the purchase order or contract, themanufacturers certification shall be furnished to the purchaserstating that the samples representing each lot have beenmanufactured,
46、tested, and inspected in accordance with thisspecification and the requirements have been met. WhenNOTE 1AChain boss to be provided at the manufacturers discretion; number of flats or lugs provided are at the manufacturers discretion.Unidentified tolerances; fractional 6132 (60.8)SizeDimensions, in.
47、 (mm)A B C (minimum) D (minimum) E12916(14.3)732(5.6)1.259(32). 834916(14.3)732(5.6)1.259(32). 81916(14.3)732(5.6)1.441(36.6). 8114916(14.3)732(5.6)1.787(45.4). 8112916(14.3)732(5.6)2.100(53.3). 82916(14.3)732(5.6)2.479(63). 821234(19)516(7.9)2.980(75.7). 8334(19)516(7.9)3.599(91.4). 841(25.4)1332(1
48、0.3)4.703(119.5). 851(25.4)1332(10.3)5.723(145.4). 861116(27)NA 6.924(175.9)34(19)2FIG. 5 Adapter Female Threads EndF1122045specified in the purchase order or contract, a report of the testresults shall be furnished.14. Product Marking14.1 Each adapter and coupler shall be marked in accor-dance with
49、 MSS-SP-25 including the following:14.1.1 ASTM designation of this specification.14.1.2 “Cl I if it is a Class I adapter or coupler.15. Packaging and Package Marking15.1 The couplings shall be packed according to the manu-facturers standard practice, providing reasonable care toprevent lost or damaged parts in shipment.15.2 Containers and packages shall be marked or tagged toadequately identify the contents or purchasers order num
