1、Designation: F1832 07 (Reapproved 2017) An American National StandardStandard Test Method forDetermining the Force-Draw and Let-Down Curves forArchery Bows1This standard is issued under the fixed designation F1832; the number immediately following the designation indicates the year oforiginal adopti
2、on or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method covers the procedure to be used todetermine the force-dra
3、w and let-down curves for archerybows.1.2 The values stated in inch-pound units are to be regardedas the standard. The SI units given in parentheses are forinformation only.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibili
4、ty of the user of this standard to establish appro-priate safety, health, and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization es
5、tablished in the Decision on Principles for theDevelopment of International Standards, Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade (TBT) Committee.2. Terminology2.1 Definitions of Terms Specific to This Standard:2.1.1 ATA (archery trade association)
6、draw length,nperpendicular distance from the point where the shootingstring of the bow contacts bottom of the nock slot of the arrow,to a vertical line through the pivot or low point of the hand grip(draw length pivot point), plus a standard dimension of 134 in.(44.5 mm).2.1.2 brace height, ndimensi
7、on in inches (millimetres),from the grip pivot point (low point) of the grip to the nearestside of the bowstring, measured perpendicular to thebowstring, with the bow strung and in the undrawn condition.2.1.3 compound bow, ntype of bow that imposes a sec-ondary system of control of the force-draw ch
8、aracteristic on theusual limb geometry control system of the conventional bow.2.1.3.1 DiscussionThis secondary control system can becomposed of cam, levers, cables, or other elements, andcombinations thereof. The dual control system permits greatversatility in the design of the force-draw characteri
9、stic, andsimplifies the inclusion of let-off. In general, it is normal forcompound bows to have greater stored energy than conven-tional bows for a given level of peak or maximum draw weight.2.1.4 draw, vto move the shooting string of a bow fromthe rest or braced position toward the full drawn posit
10、ion byapplying force to said string.2.1.4.1 DiscussionSuch action causes the limbs of thebow to bend and store energy. Moving the string from braceheight to the full draw position corresponds to the draw strokeof a bow.2.1.5 draw cycle, ncombination of the draw-stroke andthe let-down stroke, resulti
11、ng in a full cycle from brace heightto full draw and return to brace height.2.1.6 draw-stroke, ndistance in inches (millimeters) frombrace height to full draw.2.1.7 force-draw curve, ncurve that is plotted using theforce readings, taken at incremental values of draw lengthwhen drawing the bow, as th
12、e ordinate and the correspondingdraw length as abscissa.2.1.8 full draw, nposition assumed by the bowstring whenthe bow is drawn to a draw length corresponding to that fromwhich it will be released for the shot.2.1.8.1 DiscussionFor most standard test purposes fulldraw is specified as 30 in. (762 mm
13、) ATA draw length forcompound bows, and 28 in. (711.2 mm) ATA draw length fornon-compound bows, but it can take any assigned value.2.1.9 let-down curve, ncurve that is plotted using the forcereadings, taken at incremental values of draw length whenrelaxing the bow, as the ordinate and the correspond
14、ing drawlength as abscissa.2.1.10 let-off, ndifference between the peak or maximumdraw force reached during the draw stroke of a bow, and thelowest level of draw force reached subsequent to that peak.2.1.10.1 DiscussionQuantitatively, it is most frequentlyexpressed as a percentage of the peak force
15、and is then referredto as percent of let-off.1This test method is under the jurisdiction of ASTM Committee F08 onSportsEquipment, Playing Surfaces, and Facilities and is the direct responsibility ofSubcommittee F08.16 on Archery Products.Current edition approved Dec. 1, 2017. Published December 2017
16、. Originallyapproved in 1997. Last previous edition approved in 2011 as F1832 07 (2011).DOI: 10.1520/F1832-07R17.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with international
17、ly recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.12.1.11 non-compound bow, nbow constructed in the tra-dit
18、ional manner, having two flexing limbs extending outwardlyin opposite directions from a handle.2.1.11.1 DiscussionA single shooting string of a lengthshorter than the bow, connects the extreme ends of the limbscausing them to assume a pre-stressed flexed condition. Draw-ing the bow causes additional
19、 bending and stressing of thelimbs, storing the energy necessary to propel the arrow. Controlof the force-draw characteristic of the bow is exercised entirelyby the static and dynamic geometry of the flexing limbs and thebowstring.2.1.12 peak draw force, nmaximum force reached whendrawing a bow.2.1.
20、12.1 DiscussionFor conventional bows, the peak drawforce is usually reached at the full draw condition. Forcompound bows, the peak draw force is reached part waythrough the draw stroke.2.1.13 power-stroke, ndistance in inches (millimetres)from full draw to brace height.2.1.14 static hysteresis, ndif
21、ference in pounds (newtons),measured under static conditions, between the draw force andthe let-down force for any given draw length.2.1.14.1 DiscussionIntegrated over the full draw cycle ofthe bow, the static hysteresis is expressed as foot-pounds(joules) of energy.2.1.15 stored energy, nenergy req
22、uired to draw a bowfrom brace height to full draw, usually expressed in foot-pounds (joules).3. Significance and Use3.1 This test method establishes the procedure to be used tomeasure the force necessary to draw an archery bow frombrace height to the full draw position, and the holding forcenecessar
23、y to retain the bow string when the bow is let-downfrom full draw to brace height. The force values taken atincrements of draw length are then plotted versus draw lengthusing rectangular coordinates. The resulting curves are knownas the force-draw curve and the let-down curve.3.2 The force-draw curv
24、e is used to determine the energythat the limbs of the bow store when it is drawn. The area underthe curve between the positions of brace height and full drawcan be expressed as stored energy.3.3 The let-down curve is used to determine the energyrequired to restrain the bowstring as the bow is let-d
25、own fromfull draw to brace height. The energy represented by the areaunder the curve can be subtracted from the stored energy inorder to establish the static hysteresis of the bow system.4. Apparatus4.1 Force-Draw MachineA device capable of holding thebow with the restraining force located at the lo
26、w point of thegrip while the bowstring is drawn from brace height to fulldraw. The force drawing the bowstring shall be positioned nearthe center of the bowstring so the restraining and drawingforces balance, thus stabilizing the bow during the operation.The device contacting the bowstring shall be
27、a round orradiused section with a radius of18 in. (3.2 mm). The systemused to draw the bowstring shall be capable of a smooth andsteady movement, and must maintain continuous unrelaxedforce so that no hysteresis effect is experienced.4.2 Force-Reading DeviceA scale or load cell shall beinterposed be
28、tween the bowstring and the cable or rod used todraw the bowstring so that the force reading is direct and notcontaminated in any way. The force measuring device shall becapable of weighing to 0.25 lbf (1.12 N). A spring scale withadequate resolution may be capable of measuring the drawingforce for
29、conventional bows but will provide questionablevalues when used for compound bows with precipitous let-off.4.3 Draw Length ScaleA graduated scale at least 36 in.(914.4 mm) in length having commercial accuracy shall beused to measure the draw length. It shall be indexed at a point134 in. (44.5 mm) fo
30、rward of the low point or pivot point ofthe grip.5. Procedure5.1 Adjust the bow to the desired peak draw force and drawlength. On most conventional bows it will not be possible toadjust draw force and draw length, however the bowstringlength should be twisted or untwisted to provide the recom-mended
31、 brace height.5.2 To derive data for the force-draw curve, mount the bowin the force-draw device with the low or pivot point of the gripengaging the retaining surface of the device. Set the index ofthe linear scale 134 in. (44.5 mm) forward of the low point ofthe grip. Attach the drawing device to t
32、he bowstring at alocation near the center of the string, position the bowstring atbrace height, and draw the bow to the first incremental value ofdraw length. Record the force without relaxing tension toeliminate any effect of hysteresis. Continue to draw thebowstring, recording the force for each i
33、ncrement of drawlength until reaching one increment beyond the desired fulldraw position. The recorded data will be the basis of theforce-draw curve.5.3 To obtain the data for the let-down curve, relax the forceretaining the bowstring until it returns to the full draw positionand record the correspo
34、nding force. It will be somewhat lowerthan the force recorded when the bow was drawn to the sameposition. The difference is an indication of static hysteresispresent. Continue to back down the bowstring, recording theforce readings at the identical increments of draw length usedwhen the force-draw c
35、urve was established. Do this until thebowstring has returned to brace height. The recorded forcelevels and the corresponding draw length values are the datafor the let-down curve.5.4 The force-draw and let-down curves are plotted onrectangular coordinate scales with the force values as theordinate
36、and the draw length values as the abscissa. It iscommon practice to superimpose the let-down curve on theforce-draw curve. The area under the curves may be deter-mined by any acceptable method. With appropriate conversion,it is usually expressed in units of energy, for example,foot-pounds (joules).F
37、1832 07 (2017)26. Precision and Bias6.1 PrecisionThe precision of this test method for deter-mining the force-draw and let-down curves and the values ofthe energy represented is being determined.6.2 BiasNo statement on bias is being made at this timebecause no data is available on which to base an e
38、valuation ofbias.7. Keywords7.1 brace-height; compound bow; draw-stroke; force-draw;let-downASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determinatio
39、n of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdra
40、wn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your c
41、omments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single
42、or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 07 (2017)3
