1、Designation: F1932/F1932M 98 (Reapproved 2011)1An American National StandardStandard Test Method forMeasuring Sleeping Bag Loft1This standard is issued under the fixed designation F1932/F1932M; the number immediately following the designation indicates the yearof original adoption or, in the case of
2、 revision, the year of last revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon () indicates an editorial change since the last revision or reapproval.1NOTEEditorially corrected standard designation in December 2013.INTRODUCTIONThe loft (that is, thickness)
3、of a sleeping bag refers to the total thickness of a closed sleeping bag.It is a physical dimension/measurement used for specifications, design, and quality control. Loft, inand of itself, is not to be used to predict the thermal properties of a sleeping bag.1. Scope1.1 This test method covers the d
4、etermination of the loft ofa sleeping bag under a standardized load.1.2 The test method uses a physical height measurementapplicable in the laboratory.1.3 The values stated in either SI units or inch-pound unitsare to be regarded separately as standard. Within the text, theinch-pound units are shown
5、 in brackets. The values stated ineach system are not exact equivalents; therefore, each systemshall be used independently of the other. Combining valuesfrom the two systems may result in nonconformance with thetest method.1.4 This standard does not purport to address all of thesafety concerns, if a
6、ny, associated with its use. It is theresponsibility of the user of this standard to consult andestablish appropriate safety and health practices and deter-mine the applicability of regulatory limitations prior to use.2. Terminology2.1 Definitions:2.1.1 loft, nthe total thickness of a closed sleepin
7、g bag asmeasured while the bag is lying flat on a surface.2.1.2 sleeping bag, na structure made of down, syntheticfiberfill, shell fabrics, or other materials, or a combinationthereof, that is designed for people to use for thermal protec-tion when sleeping (for example, outdoors, tent, cabin).3. Si
8、gnificance and Use3.1 In this context, this test method can be used forspecifications, design, and quality control. Loft, in and of itself,is not to be used to predict the thermal properties of a sleepingbag.4. Apparatus4.1 Gantry, a rigid structure of sufficient height and width tospan all sleeping
9、 bags to be measured is required. A purpose-built device of the sort shown in Fig. 1 may be used, or astructure as simple as an office desk or workbench can suffice.4.2 Rule, having 1-mm 116-in. graduations, and longenough to measure the zero height position.4.3 Disk, having diameter of 30 cm 12 in.
10、 The weight ofthe disk plus the rule must equal 50 g 1.8 oz for a pressure of6.9 Pa 0.001 psi. Commercially available foam core dry-mount board is suitable. A range of 61 % in diameter and65 % in weight is tolerable. Mark the center of the disk forpositioning the rule during the test procedure.5. Co
11、nditioning5.1 Remove the sleeping bag from the stuff sack, zip the bagclosed, and shake it for approximately 1 min, (for example, aperson shall hold the bag and shake it, turning it periodicallyduring the shaking). Lay it flat in an uncompressed state for atleast 24 h prior to testing. A bag that ha
12、s not been compressedin the 24 h prior to testing shall be considered to be conditioned(for example, bags drawn directly from production, bagsshipped uncompressed, replicate tests).6. Procedure6.1 Perform conditioning and testing at ambient tempera-tures between 10C and 25C 55F and 80F, and at a rel
13、ativehumidity not exceeding 70 %.6.2 Place the conditioned sleeping bag on a large flat surfaceand place the gantry on the same surface, spanning the bag. Do1This test method is under the jurisdiction of ASTM Committee F08 on SportsEquipment, Playing Surfaces, and Facilities and is the direct respon
14、sibility ofSubcommittee F08.22 on Camping Softgoods.Current edition approved April 1, 2011. Published June 2011. Originallyapproved in 1998. Last previous edition approved in 2004 as F1932 98 (2004).DOI: 10.1520/F1932_F1932M-98R11E01.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700,
15、West Conshohocken, PA 19428-2959. United States1not excessively shake or refluff the sleeping bag duringplacement. Allow the bag to settle for 5 min.6.3 Place the disk on the center line of the sleeping bag, halfof the distance from the outer bottom (foot) end to the outer top(head) end of the bag.6
16、.4 Position the sleeping bag or gantry, or both, so that therule is directly over the center of the disk (see Fig. 1).6.5 Insert the rule vertically through the slot in the gantry.The gantry or sleeping bag, or both, may need to be moved toensure that the rule contacts the exact center of the disk,
17、whileremaining vertical. Allow the rule to rest upon the center of thedisk (see Fig. 1).6.6 Measurement Alternatives:6.6.1 Difference Method for Loft DerivationRead the ruleat the top of the gantry (see Fig. 1). Remove the sleeping bagand take a second rule reading of the disk alone on the testsurfa
18、ce upon which the sleeping bag had lain. The differencebetween the two readings is the loft of the sleeping bag.6.6.2 Direct Reading Method for Loft MeasurementModify the rule or the gantry, or both, to allow for verticaladjustment. Adjust so that the rule reads zero loft (that is, withthe disk alon
19、e lying on the surface upon which the sleeping bagis to be laid). Read loft directly from the rule.7. Report7.1 Report the following information:7.1.1 State that the sleeping bag was tested as directed inTest Method F1932 and explain any departures from thespecified apparatus or procedure,7.1.2 Desc
20、ribe the sleeping bag that was tested (forexample, manufacturers style and length description; whetherprototype, preproduction, or production; type and amount offill; construction details as applicable: shell and liningmaterials, baffle construction, differential cut, differential fill,multiple fill
21、s, etc.), and7.1.3 Report the loft to the nearest 1 cm 0.5 in.8. Precision and Bias8.1 PrecisionThe repeatability of the standard deviationhas been determined to be 67 %. The reproducibility of thisloft measurement test method is being determined, and will beavailable by June 1999.8.2 BiasNo informa
22、tion can be presented on the bias ofthe procedure in this test method because no material having anaccepted reference value is available.9. Keywords9.1 loft; sleeping bag; thicknessFIG. 1 Typical Gantry WeldmentF1932/F1932M 98 (2011)12ASTM International takes no position respecting the validity of a
23、ny patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to re
24、vision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. You
25、r comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copy
26、righted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).F1932/F1932M 98 (2011)13
