1、Designation: F 670 02An American National StandardStandard Specification forTanks, 5 and 10-Gal (20 and 40-L) Lube Oil Dispensing1This standard is issued under the fixed designation F 670; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revi
2、sion, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope1.1 This specification
3、 covers the material, dimensions, andconstruction of 5 and 10-gal (20 and 40-L) tanks purchased tostore and dispense lubricating oils. The tanks are industrialsafety cans mounted on a T-bar bracket, complete with driptray. .1.2 The values stated in inch-pound units are to be regardedas the standard.
4、 The values given in parentheses are forinformation only.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bili
5、ty of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:A 36/A36M Specification for Carbon Structural Steel2A 108 Specification for Steel Bars, Carbon, Cold Finished,Standard Quality3A 164 Specification for Electrodeposited Coatings of Zincon Steel4A 167 Specification for
6、 Stainless and Heat-ResistingChromium-Nickel Steel Plate, Sheet, and Strip5A 308 Specification for Steel Sheet, Cold-Rolled, Terne(Lead-Tin Alloy) Coated by the Hot-Dip Process6A 569/A569M Specification for Steel, Carbon (0.15 Maxi-mum, Percent), Hot-Rolled Sheet and Strip CommercialQuality73. Order
7、ing Information3.1 Orders for tanks under this specification shall includethe following:3.1.1 Quantity (number),3.1.2 Size, either 5 or 10 gal (20 or 40 L),3.1.3 Purchase option for finished tank materials: Terneplate (4.1.3), and3.1.4 ASTM designation and year of issue.3.2 If only size, quantity, a
8、nd ASTM designation are speci-fied and no purchase options are specified, then suppliers shallfurnish all stainless steel tanks, brass faucets with flasharrestors, and painted steel mounting columns with bolt-on driptray assemblies, which include perforated steel tray liners,drain plugs, drilled mou
9、nting holes, and mounting bolts.3.3 Optional packaging/shipping.3.3.1 If required for shipping, tanks shall be packagedindividually in cartons suitable for freight handling.4. Materials and Manufacture4.1 Materials:4.1.1 316 Stainless Steel Sheet (Specification A 167), mini-mum thickness 24 gage (0.
10、6 mm) on tank body, 22 gage (0.8mm) on tank top and bottom; body bracket, filler spout, flasharrestor, vacuum breaker valve and linkage.4.1.2 316 Stainless Steel Cast, Wrought, or Forged Flanges,(for faucet and drain).4.1.3 Terne Plate Sheet (purchase option), minimum thick-ness 22 gage (0.8 mm) on
11、tank body, top and bottom: bodybracket, filler spout (Specification A 308).4.1.4 Mild Steel:4.1.4.1 Bolt-On Column Stand, T-section, hot-rolled (Speci-fication A 36/A 36M); minimum thickness 0.160 in. (4 mm).4.1.4.2 Drip Tray Bracket, round edge, hot-rolled (Specifi-cation A 569/A569M).4.1.4.3 Drip
12、Tray Assembly, hot or cold-rolled (Specifica-tion A 108).4.1.4.4 Drip Tray Liner, 11-gage (3 mm), zinc-plated(Specification A 164).4.1.4.5 Filler Spout Cover, zinc-plated steel (SpecificationA 164).4.1.4.6 Drip Tray Drain,34-in. (20 mm) NPS drain.1This specification is under the jurisdiction of ASTM
13、 Committee F25 on Shipsand Marine Technology and is the direct responsibility of Subcommittee F25.03 onOutfitting.Current edition approved Dec. 10, 2002. Published January 2003. Originallyapproved in 1980. Last previous edition approved F 670 87 (1994)e1.2Annual Book of ASTM Standards, Vol 01.04.3An
14、nual Book of ASTM Standards, Vol 01.05.4Discontinued 1981Replaced by B 633, Annual Book of ASTM Standards,Vol02.05.5Annual Book of ASTM Standards, Vol 01.03.6Annual Book of ASTM Standards, Vol 01.06.7Discontinued 2000Replaced by A 1011/A 1011M, Annual Book of ASTMStandards, Vol 01.03.1Copyright ASTM
15、 International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.DimensionsSizeAHeight, in.BBolt Hole Spacing, in.CTank Height, in.DNumber of Bolt HolesWeight, lbDry Wet (Water)5-gal 2212 1012 978 3398110-gal 3334 1012 2078 4 49 132Note 1Dimensions and construction
16、 for guidance only.Note 21 in. = 25.4 mm.Note 31 lb = 0.4536 Kg.FIG. 1 Dimension of TankF6700224.1.5 Cast Brass:4.1.5.1 Faucet, lever-lock, self-closing,34-in. (20mm) outside diameter, male threaded.84.1.5.2 Drip Tray Drain Plug and Tank Bottom Drain Plug,34-in. (20 mm) NPS.4.1.6 Cast Aluminum, self
17、-closing, spring-action type, one-piece, filler spout cover lever.4.2 ManufactureAll sheet metal seams shall be welded.5. Dimensions and Weight5.1 The dimensions in Fig. 1 are recommended nominaldimensions. Weights are estimated and are not critical. Volumeof tanks shall be 5 and 10 gal (20 and 40 L
18、), respectively.6. Workmanship, Finish, and Appearance6.1 Workmanship on tank, stand, and drip pan shall be ofsufficient quality to prevent dirt accumulation. Welding shallhave small, even beading, free of slag and spatter. Surface ofall castings shall be of uniform texture, without cracks, pitting,
19、or flashing. Stand and drip tray shall have corners broken andall burrs removed.6.2 Tank, column, bracket, and tray shall be covered withone coat 1.5 mils (0.05 mm) thick of a zinc rich primer. Thestainless steel tank shall have no paint.7. Testing Methods7.1 Test each tank by subjecting to an inter
20、nal air pressureof 5 psi (35 kPa) with no visible seam leakage when subjectedto underwater or soap bubble test.8. Keywords8.1 lubricating oil tanks; marine; marine storage tanks;marine technology; oil dispensers; ships; tanksASTM International takes no position respecting the validity of any patent
21、rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at
22、any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments
23、 will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by
24、 ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).8Protectoseal 531G, available from The Protectoseal Co., 225 Foster Ave.,Bensenville, IL 60106, or equivalent, has been found suitable for this purpose.F670023
