1、Designation: F670 02 (Reapproved 2017) An American National StandardStandard Specification forTanks, 5 and 10-Gal (20 and 40-L) Lube Oil Dispensing1This standard is issued under the fixed designation F670; the number immediately following the designation indicates the year of originaladoption or, in
2、 the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A superscriptepsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S. Department of Defense.1. Scope1
3、.1 This specification covers the material, dimensions, andconstruction of 5 and 10-gal (20 and 40-L) tanks purchased tostore and dispense lubricating oils. The tanks are industrialsafety cans mounted on a T-bar bracket, complete with driptray.1.2 The values stated in inch-pound units are to be regar
4、dedas the standard. The values given in parentheses are forinformation only.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determi
5、ne the applica-bility of regulatory limitations prior to use.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recom-mendation
6、s issued by the World Trade Organization TechnicalBarriers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:2A36/A36M Specification for Carbon Structural SteelA108 Specification for Steel Bar, Carbon and Alloy, Cold-FinishedA164 Specification for Electrodeposited Coatings of Zinc o
7、nSteel; Replaced by B 663 (Withdrawn 1981)3A167 Specification for Stainless and Heat-ResistingChromium-Nickel Steel Plate, Sheet, and Strip (With-drawn 2014)3A308/A308M Specification for Steel Sheet, Terne (Lead-TinAlloy) Coated by the Hot-Dip Process (Withdrawn 2015)3A569/A569M Specification for St
8、eel, Carbon (0.15Maximum, Percent), Hot-Rolled Sheet and Strip Commer-cial (Withdrawn 2000)33. Ordering Information3.1 Orders for tanks under this specification shall includethe following:3.1.1 Quantity (number),3.1.2 Size, either 5 or 10 gal (20 or 40 L),3.1.3 Purchase option for finished tank mate
9、rials: Terneplate (4.1.3), and3.1.4 ASTM designation and year of issue.3.2 If only size, quantity, and ASTM designation are speci-fied and no purchase options are specified, then suppliers shallfurnish all stainless steel tanks, brass faucets with flasharrestors, and painted steel mounting columns w
10、ith bolt-on driptray assemblies, which include perforated steel tray liners,drain plugs, drilled mounting holes, and mounting bolts.3.3 Optional packaging/shipping.3.3.1 If required for shipping, tanks shall be packagedindividually in cartons suitable for freight handling.4. Materials and Manufactur
11、e4.1 Materials:4.1.1 316 Stainless Steel Sheet (Specification A167), mini-mum thickness 24 gage (0.6 mm) on tank body, 22 gage (0.8mm) on tank top and bottom; body bracket, filler spout, flasharrestor, vacuum breaker valve and linkage.4.1.2 316 Stainless Steel Cast, Wrought, or Forged Flanges,(for f
12、aucet and drain).4.1.3 Terne Plate Sheet (purchase option), minimum thick-ness 22 gage (0.8 mm) on tank body, top and bottom: bodybracket, filler spout (Specification A308/A308M).4.1.4 Mild Steel:4.1.4.1 Bolt-On Column Stand, T-section, hot-rolled (Speci-fication A36/A36M); minimum thickness 0.160 i
13、n. (4 mm).4.1.4.2 Drip Tray Bracket, round edge, hot-rolled (Specifi-cation A569/A569M).4.1.4.3 Drip Tray Assembly, hot or cold-rolled (Specifica-tion A108).1This specification is under the jurisdiction of ASTM Committee F25 on Shipsand Marine Technology and is the direct responsibility of Subcommit
14、tee F25.03 onOutfitting and Deck Machinery.Current edition approved May 1, 2017. Published June 2017. Originallyapproved in 1980. Last previous edition approved in 2007 as F670 02 (2012).DOI: 10.1520/F0670-02R17.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Cus
15、tomer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700,
16、 West Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recommendations issued by the Worl
17、d Trade Organization Technical Barriers to Trade (TBT) Committee.1DimensionsSizeAHeight, in.BBolt Hole Spacing, in.CTank Height, in.DNumber of Bolt HolesWeight, lbDry Wet (Water)5-gal 2212 1012 978 3398110-gal 3334 1012 2078 4 49 132Note 1Dimensions and construction for guidance only.Note 21 in. = 2
18、5.4 mm.Note 31 lb = 0.4536 Kg.FIG. 1 Dimension of TankF670 02 (2017)24.1.4.4 Drip Tray Liner, 11-gage (3 mm), zinc-plated(Specification A164).4.1.4.5 Filler Spout Cover, zinc-plated steel (SpecificationA164).4.1.4.6 Drip Tray Drain,34-in. (20 mm) NPS drain.4.1.5 Cast Brass:4.1.5.1 Faucet, lever-lock
19、, self-closing,34-in. (20mm) outside diameter, male threaded.44.1.5.2 Drip Tray Drain Plug and Tank Bottom Drain Plug,34-in. (20 mm) NPS.4.1.6 Cast Aluminum, self-closing, spring-action type, one-piece, filler spout cover lever.4.2 ManufactureAll sheet metal seams shall be welded.5. Dimensions and W
20、eight5.1 The dimensions in Fig. 1 are recommended nominaldimensions. Weights are estimated and are not critical. Volumeof tanks shall be 5 and 10 gal (20 and 40 L), respectively.6. Workmanship, Finish, and Appearance6.1 Workmanship on tank, stand, and drip pan shall be ofsufficient quality to preven
21、t dirt accumulation. Welding shallhave small, even beading, free of slag and spatter. Surface ofall castings shall be of uniform texture, without cracks, pitting,or flashing. Stand and drip tray shall have corners broken andall burrs removed.6.2 Tank, column, bracket, and tray shall be covered witho
22、ne coat 1.5 mils (0.05 mm) thick of a zinc rich primer. Thestainless steel tank shall have no paint.7. Testing Methods7.1 Test each tank by subjecting to an internal air pressureof 5 psi (35 kPa) with no visible seam leakage when subjectedto underwater or soap bubble test.8. Keywords8.1 lubricating
23、oil tanks; marine; marine storage tanks;marine technology; oil dispensers; ships; tanksASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of
24、the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Y
25、our comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your commen
26、ts have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or mu
27、ltiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 531G, available from The Protectoseal Co., 225 Foster Ave.,Bensenville, IL 60106, or equivalent, has been found suitable for this purpose.F670 02 (2017)3
