1、Designation: F 803 03An American National StandardStandard Specification forEye Protectors for Selected Sports1This standard is issued under the fixed designation F 803; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of l
2、ast revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers eye protectors, designed foruse by players of racket sports, womens lacrosse, field hockey,b
3、asketball, baseball, and soccer that minimize or significantlyreduce injury to the eye and adnexa due to impact andpenetration by racket-sport rackets and balls, womens lacrosseand field hockey sticks and balls, baseballs, soccer balls, hands,elbows, and fingers. Protective eyewear offers protection
4、 onlyto the eyes and does not protect other parts of the head.1.2 Protectors are divided into four types depending on theirdesign characteristics.1.3 This specification applies to eye protectors for use bywearers of corrective lenses and also by those players who donot require prescription eyewear.
5、(WarningPolycarbonatespectacle lenses should be used if spectacles are worn underprotective eyewear.)1.4 In this standard, the use of the words “shall” or “must”indicates a mandatory requirement. The word “should” indi-cates a recommendation.1.5 The values stated in SI units are to be regarded as th
6、estandard. The values given in parentheses are for informationonly. Metric units of measurement in this specification are inaccordance with the International System of Units (SI). If avalue for measurement as given in this specification is followedby an equivalent value in other units, the first sta
7、ted is to beregarded as the requirement. A given equivalent value may beapproximate.1.6 The following precautionary caveat pertains only to thetest methods portions, Sections 9-11, of this specification: Thisstandard does not purport to address all of the safety concerns,if any, associated with its
8、use. It is the responsibility of the userof this standard to establish appropriate safety and healthpractices and determine the applicability of regulatory limita-tions prior to use.2. Referenced Documents2.1 ASTM Standards:2D 1003 Test Method for Haze and Luminous Transmittanceof Transparent Plasti
9、csF 1776 Specification for Eye Protective Devices for Paint-ball Sports2.2 American National Standards:ANSI Z80.1 Requirements for First-Quality PrescriptionOphthalmic Lenses3ANSI Z80.3 Requirements for Nonprescription Sunglassesand Fashion Eyewear3ANSI Z87.1 Practice for Occupational and Educationa
10、l Eyeand Face Protectors32.3 Federal Standard:National Institute of Standards and Technology SpecialTechnical Publication 374 Method for Determining theResolving Power of Photographic Lenses (1973)43. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 binocular, adjrelating to the f
11、ield of view which isshared by both eyes simultaneously; also any simultaneousactivity of the two eyes.3.1.2 central viewing zone, nthat part of the eye of aprotector, which has its center in line with the wearers normalline of sight. The zone is circular in shape, and 40 mm indiameter. The center o
12、f the central viewing zone shall be the1This specification is under the jurisdiction of ASTM Committee F08 on SportsEquipment and Facilities and is the direct responsibility of Subcommittee F08.57 onEye Safety for Sports.Current edition approved Aug. 10, 2003. Published September 2003. Originallyapp
13、roved in 1983. Last previous edition approved in 2001 as F 803 01.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM web
14、site.3Available from American National Standards Institute (ANSI), 25 W. 43rd St.,4th Floor, New York, NY 10036.4Available from National Institute of Standards and Technology (NIST), 100Bureau Dr., Stop 3460, Gaithersburg, MD 20899-3460.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C7
15、00, West Conshohocken, PA 19428-2959, United States.point of intersection of the line of sight with the lens asmounted on the CSA headform.53.1.3 cleanable, nthe ability of a protective device to bemade readily free of dirt or grime without being damagedduring an appropriate cleaning process, such a
16、s the use of soapand water.3.1.4 coverage, na characteristic of a protective devicethat obstructs straight line paths that are coincident with thewearers eyes.3.1.5 definition (optical), nthe characteristic of a lens thatallows separate distinct points in close proximity to be dis-cerned when lookin
17、g through the lens.3.1.6 eye, nrelating to the eye of a test headform or theeye of a person wearing a protector or that part of an eyeprotective device through which a wearers eye would nor-mally look.3.1.7 eye of the headform, nall structures containedwithin the orbital rim of the CSA headform.53.1
18、.8 haze, nthe fraction of the total transmitted lightfrom a normally incident beam which is not transmitted in afocused condition but scattered by inclusions or surface de-fects. Excessive haze will reduce contrast and visibility.3.1.9 headform optical parameters, nkey dimensions forthe headforms as
19、 provided in Figs. 1-3.3.1.10 impact resistance, nthe ability of a device to affordprotection from impact as required by this specification.3.1.11 lens, nwhen so equipped, the transparent part orparts of a protective device through which the wearer normallysees.3.1.12 luminous transmittance, nlumino
20、us transmittanceis a function of the spectral transmittance of the lens weightedby the corresponding ordinates of the photopic luminousefficiency distribution of the CIE (1931) standard colorimetricobserver and by the spectral intensity of standard Illuminant C.(See ANSI Z80.3, 1986, Paragraph 3.9.1
21、.)3.1.13 normal lines of sight, nstraight ahead horizontallines that intersect the center of the eyes of the appropriateheadform.3.1.14 penetration resistance, nthe ability of a device toafford protection from moving objects as required by thisspecification.3.1.15 power imbalance, adjrelates to the
22、condition inwhich the refractive power of the lens or lenses of a protectoris different as presented to the two eyes.3.1.16 prism, na prism bends a beam of light as a result ofthe lack of parallelism of the two surfaces of a lens throughwhich the beam of light traverses. The amount of bending is afu
23、nction of the curvatures, thickness, index of refraction of thematerial and the angle of approach of the line of sight to theoptical surface. In this specification, prism refers to the amountof bending that is imposed upon the line of sight of a wearer ofan eye protector for the specified viewing po
24、sition. Prism isexpressed in diopters. The deviation of the line of sight by 1cm/m is one prism diopter.3.1.16.1 base-in, nrelating to the type of prism imbalancethat tends to cause parallel rays of light passing through aprotector, spaced apart by the interpupillary distance, to con-verge.3.1.16.2
25、base-out, nrelating to the type of prism imbal-ance that tends to cause parallel rays of light passing througha protector, spaced apart by the interpupillary distance, todiverge.3.1.16.3 base-uprefers to the type of prism that causes ahorizontal beam of light to bend upward causing objects toappear
26、lower than their true position.3.1.16.4 base-downrefers to the type of prism that causesa horizontal beam of light to bend down causing objects toappear higher than their true position.3.1.17 prism imbalance:3.1.17.1 horizontal imbalancethe difference in prismaticdeviation of incident parallel light
27、 beams on the two eyes of aprotective device in the horizontal meridian. (See base-in andbase-out).3.1.17.2 vertical imbalancethe difference in prismaticdeviation between parallel light beams incident on the two eyesof a protective device in the vertical meridian.3.1.18 protective device (or protect
28、or), na device thatprovides protection to the wearers eye against specific hazardsencountered in sports.3.1.19 refractive power, nthe focusing effect of a lensexpressed in diopters.3.1.19.1 astigmatism, na condition in a lens that createstwo axially separated line foci of each object point, the line
29、sbeing mutually perpendicular. In other words, the lens has twodifferent refractive powers in meridians that are 90 apart.3.1.20 scotoma, na blind or partially blind area within thevisual field.3.1.21 spherical power, nthe average of the maximummeridional astigmatic power and the minimum meridionala
30、stigmatic power of a lens.4. Classification4.1 Eye protectors are classified into the following types:4.1.1 Type IA protector with the lens or lenses and framefrontpiece molded as one unit. Frame temples or other devices,such as straps, to affix the lens/frontpiece may be separatepieces.4.1.2 Type I
31、IA protector with a single lens or lenses,either plano or prescription, mounted in a frame that wasmanufactured as a separate unit.4.1.3 Type IIIA protector without a lens.4.1.4 Type IVA full or partial face shield.5. General Requirements5.1 Materials of Construction:5.1.1 The manufacturers choice o
32、f material shall be inaccordance with 5.1.2 and 5.1.3.5.1.2 Materials coming into contact with the wearers faceshall not be of a type known to cause skin irritation.5.1.3 Materials coming into contact with the wearers face,except replaceable padding, shall not undergo significant lossof strength or
33、flexibility, or other physical change as a result ofperspiration, oil, or grease from the wearers skin and hair.5Available from Canadian Standards Association (CSA), 178 Rexdale Blvd.,Toronto, ON Canada M9W1R3.F8030325.1.3.1 Manufacturer will provide material selection and, byaffidavit, support sect
34、ions 5.1.1-5.1.3.5.1.4 CleanabilityProtective devices shall be capable ofbeing cleaned to the degree that when conditioned in accor-dance with the method described in 10.1, they shall remainfunctional in all ways.5.2 Finishes and ConstructionThe protector shall be con-structed in a manner to prevent
35、 the missile or components ofthe protector from contact with the eye of the headform whentested in accordance with Section 11.5.3 Straps are not required on eye protectors, provided theprotector passes the standard without straps.6. Performance Requirements6.1 Optical RequirementsType I and II Prote
36、ctors:NOTE 1Type IV protectors, full or partial face shields, shall conformto the optical requirements of Specification F 1776.6.1.1 Refractive TolerancesWhen tested in accordancewith 9.7, the spherical power shall be in the range of +0.06diopters to 0.18 diopters.Dimensions, mmA = 54.0 6 2%B and C
37、= 27.0 6 2%D and E = 95.0 6 2%F and G = 93.0 6 2%H and I = 66.0 6 2%J = 80.06 2%Note 1If headform is found to be symmetrical or is to be made symmetrical then B = C, D = E, F = G, and H = I.A = Interpupillary distance.B = Distance of right eye pupil from sagittal plane.C = Distance of left eye pupil
38、 from sagittal plane.D = Distance of right eye pupil from top of headform.E = Distance of left eye pupil from top of headform.F = Distance of top of right ear/headform junction from top of headform.G = Distance of top of left ear/headform junction from top of headform.H = Distance from right side of
39、 headform to sagittal plane.I = Distance from left side of headform to sagittal plane.J = Distance between front of pupil and top of ear/headform junction.FIG. 1 CSA 8-Year-Old ChildF8030336.1.2 AstigmatismWhen tested in accordance with 9.6,the astigmatism shall not exceed 0.12 diopter.6.1.3 Power I
40、mbalanceWhen tested in accordance with9.6, the power imbalance in corresponding meridians shall notexceed 0.18 diopters between the two eyes for straight-aheadseeing.6.1.4 PrismFor the primary viewing position of either eyeof a shield or pair of lenses, the prism deviation shall notexceed 0.50 prism
41、 diopters when tested in accordance with 9.4.6.1.5 Prism Imbalance:6.1.5.1 Vertical and Base-In0.25 prism diopters.6.1.5.2 Base-Out0.50 prism diopters.6.1.6 Luminous TransmittanceWhen tested in accordancewith 9.3, protectors shall have a luminous transmittance of notless than 85 % for a clear device
42、 and not less than 20 % fortinted devices. Additionally, the difference in values as wouldbe viewed by the two eyes through a single protector as wornshall not exceed 0.9 to 1.1 times the other value (measured atthe design line of sight) unless specifically prescribed by anophthalmic professional.6.
43、1.7 HazeWhen tested in accordance with 9.5, the hazein the protector shall not exceed 3 %.6.1.8 Lenses that exhibit any distortion or doubling of theimage during the test for refractive power or prism shall befurther tested in accordance with 9.2.6.1.9 Optical QualityWithin the central viewing zone,
44、striae warpage, surface ripples, lenticulations, or abrupt opticalchanges that are visible under the test conditions of 9.2 and thatDimensions, mmA = 59.0 6 2%B and C = 29.5 6 2%D and E = 113.0 6 2%F and G = 108.0 6 2%H and I = 73.0 6 2%J = 85.06 2%Note 1If headform is found to be symmetrical or is
45、to be made symmetrical then B = C, D = E, F = G, and H = I.A = Interpupillary distance.B = Distance of right eye pupil from sagittal plane.C = Distance of left eye pupil from sagittal plane.D = Distance of right eye pupil from top of headform.E = Distance of left eye pupil from top of headform.F = D
46、istance of top of right ear/headform junction from top of headform.G = Distance of top of left ear/headform junction from top of headform.H = Distance from right side of headform to sagittal plane.I = Distance from left side of headform to sagittal plane.J = Distance between front of pupil and top o
47、f ear/headform junction.FIG. 2 CSA 13 Year-Old Male/Adult FemaleF803034would impair the function of the lens shall be cause forrejection. Visual impairment is defined by the scanning andfocimeter test of 9.2.6.1.10 Surface and Internal DefectsPits, scratches,bubbles, grayness, specks, cracks, and wa
48、ter marks that arevisible under the test conditions of 9.7 and that would impairthe function of the lens shall be a cause for rejection. Graynessshould be evaluated by the requirements of 6.1.6.6.2 Mechanical Requirements:6.2.1 No contact with the eye of the headform shall bepermitted when tested in
49、 accordance with Section 11.6.2.2 When tested in accordance with Section 11, displacedfragments or complete fracture of the frame or lenses consti-tutes a failure.6.2.3 When tested in accordance with Section 11, anydisplacement of the lens from the frame constitutes a failure.6.2.4 A protector that is dislodged from the test headformwhen tested in accordance with Section 11 shall not constitutea failure, provided all of the above mechanical requirementsare met.7. Sample Preparation7.1 Only new and complete eye protectors as