1、Designation: F823 93 (Reapproved 2010)An American National StandardStandard Specification forDesk, Log, Marine, Steel, with Cabinet1This standard is issued under the fixed designation F823; the number immediately following the designation indicates the year of originaladoption or, in the case of rev
2、ision, the year of last revision. A number in parentheses indicates the year of last reapproval. A superscriptepsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers the construction of marine logdesks of steel construction with cabinets.1
3、.2 Values stated in inch-pound units are to be regarded asthe standard. The metric equivalents, given in parentheses, areprovided for information only.2. Referenced Documents2.1 ASTM Standards:2A366/A366M Specification for Commercial Steel (CS)Sheet, Carbon, (0.15 Maximum Percent) Cold-Rolled3D907 T
4、erminology of AdhesivesF782 Specification for Doors, Furniture, MarineF825 Specification for Drawers, Furniture, Marine, SteelF826 Specification for Tops, Furniture, Marine, Steel2.2 American Institute of Steel Construction Manual:AISC Wire and Sheet Metal Gages Equivalent Thicknessin Decimals of an
5、 Inch, U.S. Standard Gage for UncoatedHot and Cold Rolled Sheets43. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 log desk with cabineta desk with attached cabinetlocated in various places aboard ship for making records andfor storage. Log desk has a drawer with a writing surfa
6、ce at thetop and a cabinet with adjustable shelves and doors below.4. Ordering Information4.1 Orders for items purchased under this specification shallinclude the following information:4.1.1 Quantity.4.1.2 Paint:4.1.2.1 ColorPurchaser shall pick from manufacturerssamples or submit sample chip of col
7、or desired.4.1.2.2 Manufacturers standard baked enamel will be fur-nished unless otherwise required and indicated by the pur-chaser.4.1.3 Options for Tops:4.1.3.1 Unless otherwise specified in the ordering docu-ments, the top supplied by the furniture manufacturer may be,at his option, Type I, II, I
8、II, or IV in accordance withSpecification F826.4.1.3.2 Color or pattern of top covering material shall bespecified.4.1.4 Options for DrawersDrawer locks shall be fur-nished only when specified in ordering documents. Masterkeying of drawer locks will not be provided unless requiredand defined by the
9、ordering documents. See Specification F825for lock description.4.1.5 Options for DoorsDoor locks shall be furnishedonly when specified in ordering documents. Master keying ofdoor locks will not be provided unless required and defined inthe ordering documents. Doors shall be Type I in accordancewith
10、Specification F782.4.1.6 If the total weight of the chest of drawers is requiredit shall be requested by the purchaser.5. Materials and Manufacture5.1 For typical design, see Fig. 1.5.2 Sheet metal shall be in accordance with SpecificationA366/A366M, commercial quality.5.2.1 Minimum sheet metal thic
11、kness shall be:5.2.1.1 Sides and front rails 18 USSG (0.0478 in. or 1.2mm).5.2.1.2 Back 20 USSG (0.0359 in. or 0.9 mm).5.2.1.3 Base frame 16 USSG (0.0598 in. or 1.5 mm).5.3 Joining of Metal Components:5.3.1 Metal components shall be joined by welding orgluing with a structural adhesive as defined in
12、 TerminologyD907. The back panel may be riveted to case provided rivetsare not visible after installation.5.3.2 Joining shall be adequate to prevent racking of chestduring handling.1This specification is under the jurisdiction of ASTM Committee F25 on Shipsand Marine Technology and is the direct res
13、ponsibility of Subcommittee F25.03 onOutfitting and Deck Machinery.Current edition approved March 1, 2010. Published April 2010. Originallyapproved in 1983. Last previous edition approved in 2004 as F823 93 (2004).DOI: 10.1520/F0823-93R10.2For referenced ASTM standards, visit the ASTM website, www.a
14、stm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Withdrawn.4Available from American Institute of Steel Construction (AISC), One E.Wacker Dr., Suite 700, Chicago, IL 60601
15、-2001, http:/www.aisc.org.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.5.3.3 Spotwelds shall be spaced approximately 3 in. (76mm) on centers.5.3.4 Visible spotwelds, higher than the general surface ofthe adjacent metal, shall be g
16、round flush.5.3.5 Visible spotweld depressions shall be spot filled andsanded flush.5.4 Side panels shall be stiffened suitably to prevent buck-ling or oil-canning.5.5 Sound deadening shall be vermin proof and applied toback and inner face of sides of chest. Location and thickness ofapplied sound de
17、adener shall be as required to sound-deadenchest.5.6 Top shall be manufactured in accordance with Specifi-cation F826.5.7 Drawers shall be manufactured in accordance withSpecification F825.5.8 Doors shall be Type I, Grade A and shall be manufac-tured in accordance with Specification F782.5.9 Cabinet
18、 section shall be provided with two adjustableshelves.5.10 Top shall be provided with a pencil tray along backedge.5.11 A furniture base shall be provided suitable for securinglog desk to deck.6. Performance Requirements6.1 The completed log desk with cabinet, with top, drawers,and doors installed,
19、shall satisfy the corresponding perfor-mance requirements outlined in Specifications F826, F825, andF782.7. Dimensions7.1 For dimensions, see Table 1.8. Workmanship, Finish, and Quality Assurance8.1 All workmanship and material shall be of specifiedquality in keeping with the best commercial marine
20、practice soas to produce each item suitable for its intended use.8.2 All exposed burrs, raw or sharp edges which might beinjurious to personnel shall be removed.8.3 Depressions considered unacceptable for products enduse shall be spot filled and sanded smooth.8.4 Finish:8.4.1 All steel surfaces unle
21、ss corrosion resistant or with acorrosion-resistant plating shall be painted so as to preventcorrosion.8.4.2 Unless otherwise required by the ordering documents,all parts normally visible on the completed unit shall have themanufacturers standard baked-on enamel finish.8.4.3 Color to be specified in
22、 the ordering documents.NOTE 1For description of Type I, II, III, and IV tops, see Specification F826.NOTE 2For description of drawers, see Specification F825.NOTE 3For description of Type I doors and available alternates, see Specification F782.NOTE 4If log desk is located in a corner, Dimension “F
23、” next to this adjacent wall shall be 0 in. (0 mm). In all other cases, the minimum value forDimension “F” shall be34 in. (19.05 mm).NOTE 5The minimum value for Dimension “H” shall be 4 in. (102 mm).FIG. 1 Log Desk with CabinetF823 93 (2010)29. Inspection and Certification9.1 Manufacturer shall insp
24、ect and certify that the item offurniture complies with the furniture specification and theloading requirements as defined in Section 6.10. Packaging and Package Marking10.1 Each item shall be marked in accordance with thepurchase order.10.2 Packaging shall be provided and shall be acceptable toa co
25、mmon carrier.11. Keywords11.1 cabinets; log desks; marine furniture; marine log desks;steel log desksASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that det
26、ermination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved o
27、r withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel th
28、at your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints
29、 (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM w
30、ebsite (www.astm.org/COPYRIGHT/).TABLE 1 Dimensions of Log Desk with CabinetDesignationin. mmDimension Tolerance To + Or Dimension Tolerance To + Or Width A 30116 762 2Height B 42116 1067 2Depth C 24116 610 2Drawer section overhang D 558116 143 2Toespace, front, E 3 max116 76 max 2Toespace, side,AF
31、4 max116 102 max 2Drawer section height G 7 max116 178 max 2Base heightBH 434 max116 121 max 2AIf log desk is located in a corner, Dimension F next to this adjacent wall shall be 0 in. (0 mm). In all other cases, the minimum value for Dimension F shall be34 in.(19 mm).BThe minimum value for Dimension H shall be 4 in. (120 mm).F823 93 (2010)3
