1、AWWA Standard SM Dimensions for Fabricated Steel Water Pipe Fittings Effective date: Dec. 1, 2017. First edition approved by AWWA Board of Directors Jan. 26, 1959. This edition approved June 11, 2017. Approved by American National Standards Institute Sept. 7, 2017. ANSI/AWWA C208-17 (Revision of ANS
2、I/AWWA C208-12) Copyright 2017 American Water Works Association. All Rights Reserved. ii AWWA Standard This document is an American Water Works Association (AWWA) standard. It is not a specification. AWWA standards describe minimum requirements and do not contain all of the engineering and administr
3、ative information normally contained in specifications. The AWWA standards usually contain options that must be evaluated by the user of the standard. Until each optional feature is specified by the user, the product or service is not fully defined. AWWA pub- lication of a standard does not constitu
4、te endorsement of any product or product type, nor does AWWA test, certify, or approve any product. The use of AWWA standards is entirely voluntary. This standard does not supersede or take precedence over or displace any applicable law, regulation, or code of any governmental authority. AWWA standa
5、rds are intended to represent a consensus of the water industry that the product described will provide satisfactory ser- vice. When AWWA revises or withdraws this standard, an official notice of action will be placed on the first page of the Official Notice section of Journal American Water Works A
6、ssociation. The action becomes effective on the first day of the month following the month of Journal American Water Works Association publication of the official notice. American National Standard An American National Standard implies a consensus of those substantially concerned with its scope and
7、provisions. An American National Standard is intended as a guide to aid the manufacturer, the consumer, and the general public. The existence of an American National Standard does not in any respect preclude anyone, whether that person has approved the standard or not, from manufacturing, marketing,
8、 purchasing, or using products, processes, or proce - dures not conforming to the standard. American National Standards are subject to periodic review, and users are cau- tioned to obtain the latest editions. Producers of goods made in conformity with an American National Standard are encouraged to
9、state on their own responsibility in advertising and promotional materials or on tags or labels that the goods are produced in conformity with particular American National Standards. Caution n oti Ce : The American National Standards Institute (ANSI) approval date on the front cover of this standard
10、 indicates completion of the ANSI approval process. This American National Standard may be revised or withdrawn at any time. ANSI procedures require that action be taken to reaffirm, revise, or withdraw this standard no later than five years from the date of publication. Purchasers of American Natio
11、nal Standards may receive current information on all standards by calling or writing the American National Standards Institute, 25 West 43rd Street, Fourth Floor, New York, NY 10036; 212.642.4900; or emailing infoansi.org. hours of work by your fellow water professionals. Revenue from the sales of t
12、his AWWA material supports ongoing product development. Unauthorized distribution, either electronic or photocopied, is illegal and hinders AWWAs mission to support the water community. This AWWA content is the product of thousands of ISBN-13, print: 978-1-62576-271-9 eISBN-13, electronic: 978-1-613
13、00-445-5 DOI:http:/dx.doi.org/10.12999/AWWA.C108.17 All rights reserved. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopy, recording, or any information or retrieval system, except in the form of brief excerpts or
14、 quotations for review purposes, without the written permission of the publisher. Copyright 2017 by American Water Works Association Printed in USAiii Committee Personnel The Steel Water Pipe Manufacturers Technical Advisory Committee (SWPMTAC) Task Group on C208, which reviewed and revised this sta
15、ndard, had the following personnel at the time: John L. Luka, Chair General Interest Members R.J. Card, Manufacturing Consultant, Sugar Hill, Ga. (AWWA) R.R. Collins, JCM Industries, Nash, Texas (AWWA) K. Couture, American SpiralWeld Pipe Company, Birmingham, Ala. (AWWA) D. Dechant, Manufacturing Co
16、nsultant, Aurora, Colo. (AWWA) B.D. Keil, Northwest Pipe Company, Draper, Utah (AWWA) J.L. Luka, American SpiralWeld Pipe Company, Columbia, S.C. (AWWA) R.N. Satyarthi, Baker Coupling Company Inc., Los Angeles, Calif. (AWWA) D. Seals, JCM Industries, Nash, Texas (AWWA) K.L. Shaddix, Smith-Blair Inc.
17、, Texarkana, Texas (AWWA) B. Simpson, American SpiralWeld Pipe Company, Birmingham, Ala. (AWWA) The Standards Committee on Steel Pipe, which reviewed and approved this standard, had the fol - lowing personnel at the time of approval: John H. Bambei Jr., Chair Dennis Dechant, Vice-Chair John L. Luka,
18、 Secretary General Interest Members J.H. Bambei Jr., Bambei Engineering Services, Arvada, Colo. (AWWA) W.R. Brunzell, Brunzell Associates Ltd., Skokie, Ill. (AWWA) R.J. Card, Lockwood, Andrews write to the department at 6666 West Quincy Avenue, Denver, CO 80235-3098; or email at standardsawwa.org. Copyright 2017 American Water Works Association. All Rights Reserved.
