1、BRITISH STANDARD CONFIRMED APRIL1993 BS3488:1987 Incorporating Amendment No.1 Specification for Technical anhydrous lanolin UDC 665.238BS3488:1987 This BritishStandard, having been prepared under the directionof the Food and Agriculture Standards Committee,was published underthe authority of the Boa
2、rdofBSI and comesintoeffecton 30October1987 BSI12-1999 First publishedApril1962 First revisionOctober1987 The following BSI references relate to the work on this standard: Committee referenceFAC/18 Draft for comment86/54856DC ISBN 0 580 16189 7 Committees responsible for this British Standard The pr
3、eparation of this BritishStandard was entrusted by the Food and Agriculture Standards Committee (FAC/-) to Technical CommitteeFAC/18, upon which the following bodies were represented: AFRC Institute of Food Research, Bristol Laboratory AFRC Institute of Food Research, Reading Laboratory Association
4、of Public Analysts British Food Manufacturing Industries Research Association Cooperative Union Department of Trade and Industry (Laboratory of the Government Chemist) FOSFA International International Association of Seed Crushers Margarine and Shortening Manufacturers Association Ministry of Agricu
5、lture, Fisheries and Food Overseas Development Administration Tropical Development and Research Institute Retail Consortium Royal Society of Chemistry Rubber Growers Association Seed Crushers and Oil Processors Association Soap and Detergent Industry Association United Kingdom Glycerine Producers As
6、sociation United Kingdom Renderers Association Ltd. Amendments issued since publication Amd. No. Date of issue Comments 6162 February1990 Indicated by a sideline in the marginBS3488:1987 BSI 12-1999 i Contents Page Committees responsible Inside front cover Foreword ii 1 Scope 1 2 Description 1 3 Aci
7、d value 1 4 Saponification value 1 5 Iodine value 1 6 Moisture and other volatile matter 1 7 Melting point 1 8 Ash 1 9 Matter soluble in water 1 10 pH value of aqueous extract 1 11 Sulphur 1 Appendix A Determination of matter soluble in water 2 Appendix B Determination of pH value of aqueous extract
8、 2 Appendix C Detection of sulphur 2 Publications referred to Inside back coverBS3488:1987 ii BSI 12-1999 Foreword This revision of BS3488 has been prepared under the direction of the Food and Agriculture Standards Committee. It supersedes BS3488:1962 from which it differs in that requirements are a
9、ligned more closely with those of the British Pharmacopoeia and that the requirement for freedom from ammonia and ammonium compounds has been deleted. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their corre
10、ct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pagesi andii, pages1 and2, an inside back cover and a back cover. This standard has been updated (see copyright
11、 date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.BS3488:1987 BSI 12-1999 1 1 Scope This BritishStandard specifies requirements for anhydrous lanolin suitable for technical uses, for example as an easily removable rust preventati
12、ve or protective film agent. It is not applicable to lanolin for medical or cosmetic use. NOTEThe titles of the publications referred to in this standard are listed on the inside back cover. 2 Description The material shall consist of purified recovered wool fat. It shall be of uniform consistency,
13、free from visible impurities and have the characteristic odour and colour of lanolin. 3 Acid value The acid value, when determined by method2 of BS684-2.10:1988, shall be not higher than1.5. 4 Saponification value The saponification value, when determined by the method described in BS684-2.6, shall
14、be not lower than90 and not higher than106. 5 Iodine value The iodine value, when determined by the method described in BS684-2.13 using a test portion of1g, shall be not lower than17 and not higher than35. 6 Moisture and other volatile matter The moisture and other volatile matter content, when det
15、ermined by method A of BS684-1.10:1982, shall not exceed0.3%(m/m). 7 Melting point The melting point, when determined as the drop point by method1 of BS684-1.4:1976, shall be not lower than38 C and not higher than44 C. The cap shall be filled by the following method. Melt the wool fat on a water-bat
16、h, cool to about50 C, pour into the cup and allow to stand for24h at15 C to20 C. 8 Ash The ash, when determined by the method described in BS684-2.2, shall not exceed0.15%(m/m). 9 Matter soluble in water The content of matter soluble in water, when determined by the method described in Appendix A, s
17、hall not exceed0.1%(m/m). 10 pH value of aqueous extract The pH value of an aqueous extract, when determined by the method described in Appendix B, shall be not lower than5.0 and not higher than8.0. 11 Sulphur The material, when tested by the method described in Appendix C, shall cause no pitting or
18、 etching and no more than slight discoloration of the copper strip.BS3488:1987 2 BSI 12-1999 Appendix A Determination of matter soluble in water A.1 Procedure Boil20g of the sample for5min with approximately200mL of neutral distilled water. Cool the mixture to room temperature and filter through a w
19、ater-wetted filter paper into a250mL one-mark volumetric flask. Wash the filter with small quantities of the neutral distilled water adding the washings to the filtrate and, if necessary, filter again. Dilute the filtrate to the mark. Transfer a50mL portion of the filtrate to a glass or platinum dis
20、h, weighed to the nearest0.1mg, evaporate to dryness on a steam bath and dry for1h in an oven maintained at105 1 C. A.2 Expression of results The content of matter soluble in water, expressed as a percentage by mass, is given by the expression 25M where M is the mass of residue (ing). Appendix B Det
21、ermination of pH value of aqueous extract Boil20g of the sample for5min with200mL of recently boiled distilled water in a500mL beaker. Cool the mixture to room temperature and allow to stand. When the liquid is clear, decant about70mL of the liquor into a100mL beaker. Determine the pH value of the d
22、ecanted liquor electrometrically using a pH meter. Appendix C Detection of sulphur C.1 Reagents C.1.1 Strips of sheet copper, 755mm long by10 2mm wide complying with BS2870 or BS4608. C.1.2 Silicon carbide powder C.1.3 Acetone C.1.4 White spirit, complying with BS245. C.2 Preparation of strips If th
23、e copper strips(C.1.1) do not have a uniform finish, free from defects, polish them mechanically on both sides to obtain a uniform finish, free from defects. Clean and polish the strips with a pad of cotton wool and the silicon carbide powder(C.1.2) and then with successive pads of cotton wool until
24、 a fresh pad remains unsoiled after use. Wash the strips with the acetone(C.1.3) and allow to dry. Use clean metal forceps for all further handling of the strips. C.3 Procedure Dissolve20g of the sample in100mL of the white spirit(C.1.4). Immerse a strip of copper, prepared as inC.2, to a depth of50
25、mm in the solution contained in a glass test tube. Close the test tube with a vented cork and allow to stand in a vertical position at room temperature. Remove the strip after24h, wash with white spirit and compare with similar strips of freshly cleaned and polished copper.BS3488:1987 BSI 12-1999 Pu
26、blications referred to BS245, Specification for mineral solvents (white spirit and related hydrocarbon solvents) for paints and other purposes. BS684, Methods of analysis of fats and fatty oils. BS684-1.4, Determination of flow and drop points. BS684-1.10, Determination of moisture and other volatil
27、e matter. BS684-2.2, Determination of ash. BS684-2.6, Determination of saponification value. BS684-2.10, Determination of acidity. BS684-2.13, Determination of iodine value. BS2870, Specification for rolled copper and copper alloys: sheet, strip and foil. BS4608, Specification for copper for electri
28、cal purposes. Rolled sheet, strip and foil. BS3488:1987 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorp
29、orated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone
30、finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which e
31、nsures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is B
32、SI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Se
33、rvice. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on
34、 the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodie
35、s. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free u
36、se, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.
