1、BRITISH STANDARD BS 7851:1996 IEC 1119-7: 1995 Digital audio tape cassette system (DAT) DAT logo application rule ICS 33.160.30BS7851:1996 This British Standard, having been prepared under the directionof the ElectrotechnicalSector Board,was published undertheauthority of the Standards Board and com
2、esintoeffect on 15 May 1996 BSI 09-1999 The following BSI references relate to the work on this standard: Committee reference EPL/100/2 Draft for comment 93/212601 DC ISBN 0 580 25568 9 Committees responsible for this British Standard The preparation of this British Standard was entrusted by Technic
3、al Committee EPL/100, Audio, video and multimedia systems and equipment, to Subcommittee EPL/100/2, Recording, upon which the following bodies were represented: Association of Professional Recording Services Limited Audio Engineering Society British Broadcasting Corporation British Kinematograph, So
4、und and Television Society British Tape Industry Association Federation of the Electronics Industry ITV Association (ITVA) Royal Television Society Amendments issued since publication Amd. No. Date CommentsBS7851:1996 BSI 09-1999 i Contents Page Committees responsible Inside front cover National for
5、eword ii 1 Scope 1 2 Bibliographical references 1 3 DAT logo types 1 4 DAT logo application rules 1 5 Copyright of DAT logo 1 6 Supply of DAT logo information 1 7 Detailed specification of the DAT logo 1 Figure 1 Basic DAT logo 2 Figure 2 Solid DAT logo 2 Figure 3 Wide letters for Digital Audio Tape
6、 3 Figure 4 Solid DAT logo. Extended letters for Digital Audio Tape 3 Figure 5 Examples of DAT logos 4 List of references Inside back coverBS7851:1996 ii BSI 09-1999 National foreword This British Standard has been prepared by Technical Subcommittee EPL/100/2 and is identical with IEC 1119-7:1995, p
7、ublished by the International Electrotechnical Commission (IEC). This standard is Part of the IEC 1119 series, the other Parts of which have mostly been published as ENs by the European Committee for Electrotechnical Standardization (CENELEC) and implemented as a BSEN61119 series. IEC1119 includes t
8、he following Parts: Part 1: Dimensions and characteristics (EN 61119-1:1994); Part 2: DAT calibration tape (EN 61119-2:1994); Part 3: DAT tape properties (EN 61119-3:1994); Part 4: Character pack format 1) ; Part 5: DAT for professional use (EN 61119-5:1995); Part 6: Serial copy management system (E
9、N 61119-6:1994); A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This do
10、cument comprises a front cover, an inside front cover, pages i and ii, pages 1 to 4, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. 1) In pre
11、paration. Cross-references Publication referred to Corresponding British Standard BS EN 61119 Digital audio tape cassette system (DAT) IEC 1119-1:1992 Part 1:1994 Dimensions and characteristics IEC 1119-2:1991 Part 2:1994 DAT calibration tape IEC 1119-3:1992 Part 3:1994 DAT tape properties IEC 1119-
12、6:1992 Part 6:1994 Serial copy management systemBS7851:1996 BSI 09-1999 1 1 Scope This technical report defines the use of the DAT logo on DAT equipment and accessories. It provides information on the specification, copyright, and application rule of the logo. 2 Bibliographic references IEC 1119-1:1
13、992, Digital audio tape cassette system (DAT) Part 1: Dimensions and characteristics. IEC 1119-2:1991, Digital audio tape cassette system (DAT) Part 2: DAT calibration tape. IEC 1119-3:1992, Digital audio tape cassette system (DAT) Part 3: DAT tape properties. IEC 1119-4, Digital audio tape cassette
14、 system (DAT) Part 4: Character pack format (under consideration). IEC 1119-6:1992, Digital audio tape cassette system (DAT) Part 6: Serial copy management system. 3 DAT logo types Figure 1 to Figure 5 show several DAT logo types. The DAT logo is composed of two phrases, “DAT” and “Digital Audio Tap
15、e”. Details of the logo types are specified in 7.4. The use of each logo is restricted and defined in the application rules for DAT logos. 4 DAT logo application rules 4.1 The DAT logo assures compatibility between DAT cassette systems for consumer use, manufactured in conformance with the DAT casse
16、tte system specifications as laid down in IEC 1119-1 to IEC 1119-6. The DAT logo shall be used on all consumer DAT recorders/players and related products, including DAT tapes. 4.2 The manufacturers involved with the production of DAT cassette recorders/players and related products shall positively p
17、romote the use of the DAT logo. 5 Copyright of the DAT logo 5.1 The use of the DAT logo is recommended, but left to the discretion of the manufacturers concerned. 5.2 Should a third party claim the rights on the use of any of the DAT logo types, he who receives the claim shall notify the EIAJ withou
18、t delay. The EIAJ can be contacted at the following address: ELECTRONIC INDUSTRIES ASSOCIATION OF JAPAN 3-2-2 Marunouchi, Chiyodaku, Tokyo 100 Japan 6 Supply of DAT logo information The manufacturer who wishes to use the DAT logo shall ask EIAJ for clean proofs of the DAT logo types. 7 Detailed spec
19、ification of the DAT logo 7.1 Figure 1 shows the basic DAT logo. 7.2 The DAT logo type may be enlarged or reduced. 7.3 Figure 2, Figure 3, and Figure 4 show modified DAT logos. These modified logo types may be used only under the following conditions. 7.3.1 Figure 2: Solid DAT logo When printing obs
20、cures the details of the striped DAT logo. 7.3.2 Figure 3: Wide letters for Digital Audio Tape When printing obscures the details of the characters of Digital Audio Tape. 7.3.3 Figure 4: Solid DAT logo with extended letters for Digital Audio Tape When the letters become obscured, as in cases 7.3.1 a
21、nd 7.3.2.BS7851:1996 2 BSI 09-1999 7.3.4 Solid DAT and Digital Audio Tape Only when the height of DAT is 15mm or less, and when the DAT logo type becomes obscured when printed. 7.3.5 The modified DAT logo types shall never be used in any material for publicity and advertisement. 7.4 A boxed DAT logo
22、 shall not be used. 7.5 The use of colour for the DAT logo type is neither specified nor restricted. 7.6 Figure 5 shows examples of DAT logos. Figure 1 Basic DAT logo Figure 2 Solid DAT logoBS7851:1996 BSI 09-1999 3 Figure 3 Wide letters for Digital Audio Tape Figure 4 Solid DAT logo. Extended lette
23、rs for Digital Audio TapeBS7851:1996 4 BSI 09-1999 Figure 5 Examples of DAT logosBS7851:1996 BSI 09-1999 List of references See national foreword.BS 7851:1996 IEC1119-7: 1995 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for
24、preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editi
25、ons. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the insi
26、de front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addre
27、ssed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of i
28、nformation on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089
29、967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BS
30、I publications. BSI also holds the copyright, in the UK, of the publications of the internationalstandardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electro
31、nic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.
