BS EN 302-1-2013 Adhesives for load-bearing timber structures Test methods Determination of longitudinal tensile shear strength《承重木结构用胶粘剂 试验方法 纵向抗拉伸剪切强度的测定》.pdf

上传人:arrownail386 文档编号:550386 上传时间:2018-12-09 格式:PDF 页数:18 大小:961.40KB
下载 相关 举报
BS EN 302-1-2013 Adhesives for load-bearing timber structures Test methods Determination of longitudinal tensile shear strength《承重木结构用胶粘剂 试验方法 纵向抗拉伸剪切强度的测定》.pdf_第1页
第1页 / 共18页
BS EN 302-1-2013 Adhesives for load-bearing timber structures Test methods Determination of longitudinal tensile shear strength《承重木结构用胶粘剂 试验方法 纵向抗拉伸剪切强度的测定》.pdf_第2页
第2页 / 共18页
BS EN 302-1-2013 Adhesives for load-bearing timber structures Test methods Determination of longitudinal tensile shear strength《承重木结构用胶粘剂 试验方法 纵向抗拉伸剪切强度的测定》.pdf_第3页
第3页 / 共18页
BS EN 302-1-2013 Adhesives for load-bearing timber structures Test methods Determination of longitudinal tensile shear strength《承重木结构用胶粘剂 试验方法 纵向抗拉伸剪切强度的测定》.pdf_第4页
第4页 / 共18页
BS EN 302-1-2013 Adhesives for load-bearing timber structures Test methods Determination of longitudinal tensile shear strength《承重木结构用胶粘剂 试验方法 纵向抗拉伸剪切强度的测定》.pdf_第5页
第5页 / 共18页
亲,该文档总共18页,到这儿已超出免费预览范围,如果喜欢就下载吧!
资源描述

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 302-1:2013Adhesives for load-bearing timber structures T e s t m e t h o d sPart 1: Determination of longitudinal tensile shear strengthBS EN 302-1:2013 BRITISH STANDARDNat

2、ional forewordThis British Standard is the UK implementation of EN 302-1:2013. It supersedes BS EN 302-1:2004, which is withdrawn.The UK participation in its preparation was entrusted to T e c h n i c a l C o m m i t t e e P R I / 5 2 , A d h e s i v e s .A list of organizations represented on this

3、committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2013. Published by BSI Standards Limited 2013.ISBN 978 0 580 75255 1 ICS

4、 83.180 Compliance with a British Standard cannot confer immunityfrom legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 April 2013.Amendments issued since publicationDate T e x t a f f e c t e dBS EN 302-1:2013EUROPEAN STAN

5、DARD NORME EUROPENNE EUROPISCHE NORM EN 302-1 March 2013 ICS 83.180 Supersedes EN 302-1:2004English Version Adhesives for load-bearing timber structures - Test methods - Part 1: Determination of longitudinal tensile shear strength Adhsifs pour structures en bois - Mthodes dessais - Partie 1: Dtermin

6、ation de la rsistance du joint au cisaillement en traction longitudinale Klebstoffe fr tragende Holzbauteile - Prfverfahren - Teil 1: Bestimmung der Lngszugscherfestigkeit This European Standard was approved by CEN on 5 February 2013. CEN members are bound to comply with the CEN/CENELEC Internal Reg

7、ulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN mem

8、ber. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.

9、CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland

10、, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2013 CEN All rights of exploitation in any form an

11、d by any means reserved worldwide for CEN national Members. Ref. No. EN 302-1:2013: EBS EN 302-1:2013EN 302-1:2013 (E) 2 Contents Page Foreword 3 Introduction .4 1 Scope 6 2 Normative references 6 3 Terms and definitions .6 4 Symbols 7 5 Principle 7 6 Apparatus .7 7 Method 7 7.1 Preparation of panel

12、s 7 7.2 Preparation of the bonded assemblies8 7.2.1 Wood adherends and bonding procedure 8 7.2.2 Close contact glue .9 7.2.3 Thick glue lines (gap joints) .9 7.3 Preparation of test pieces .9 7.4 Number of test pieces 10 7.5 Treatment prior to tensile shear testing . 10 7.6 Test procedure 11 8 Expre

13、ssion of results . 12 9 Test report . 12 9.1 The adhesive . 12 9.2 Preparation of test pieces and testing procedure . 12 9.3 Test results 12 Bibliography . 14 BS EN 302-1:2013EN 302-1:2013 (E) 3 Foreword This document (EN 302-1:2013) has been prepared by Technical Committee CEN/TC 193 “Adhesives”, t

14、he secretariat of which is held by AENOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2013 and conflicting national standards shall be withdrawn at the latest by September 2013. Atte

15、ntion is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 302-1:2004. The following modifications have been made: Two ne

16、w clauses (Terms and definitions and Symbols) are introduced in this revised standard; Thick glue line is now prepared with thicknesses between 0,3 mm and 2,0 mm depending on type of adhesive; There has been given more detailed instructions on how to prepare thick glue line; The condition period for

17、 bonded assemblies has been increased. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugo

18、slav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 302-1:2013EN 302-1:2013 (E) 4 Introduction

19、 This document is one of a series dealing with adhesives for use with timber structures, and is published in support of EN 1995, Eurocode 5: Design of timber structures. The series consists of three classification and performance requirements for adhesives for load-bearing timber structures, phenoli

20、c and aminoplastic adhesives (EN 301), one component polyurethane adhesives (EN 15425) and emulsion polymerised isocyanate adhesives (prEN 16254), together with eleven test methods (EN 302 Parts 1 to 7 and EN 15416 Parts 2 to 5). These European Standards have the following titles: EN 301, Adhesives,

21、 phenolic and aminoplastic, for load-bearing timber structures Classification and performance requirements EN 15425, Adhesives One component polyurethane for load bearing timber structures Classification and performance requirements prEN 16254, Adhesives Emulsion polymerized isocyanate (EPI) for loa

22、d-bearing timber structures Classification and performance requirements EN 302, Adhesives for load-bearing timber structures Test methods Part 1: Determination of longitudinal tensile shear strength Part 2: Determination of resistance to delamination Part 3: Determination of the effect of acid damag

23、e to wood fibres by temperature and humidity cycling on the transverse tensile strength Part 4: Determination of the effects of wood shrinkage on the shear strength Part 5: Determination of maximum assembly time under referenced conditions Part 6: Determination of the minimum pressing time under ref

24、erenced conditions Part 7: Determination of the working life under referenced conditions EN 15416, Adhesives for load bearing timber structures other than phenolic and aminoplastic Test methods Part 2: Static load test of multiple bondline specimens in compression shear Part 3: Creep deformation tes

25、t at cyclic climate conditions with specimens loaded in bending shear Part 4: Determination of open assembly time for one component polyurethane adhesives Part 5: Determination of conventional pressing time Safety statement Persons using this document should be familiar with the normal laboratory pr

26、actice, if applicable. This document cannot address all of the safety problems, if any, associated with its use. It is the responsibility of the user to establish appropriate safety and health practices and to ensure compliance with any regulatory conditions. BS EN 302-1:2013EN 302-1:2013 (E) 5 Envi

27、ronmental statement It is understood that some of the material permitted in this standard can have a negative environmental impact. As technological advantages lead to better alternatives for these materials, they will be eliminated from this standard to the greatest extent possible. At the end of t

28、he test, it is recommended that the user of the standard take care to carry out an appropriate disposal of the wastes, according to local regulations. BS EN 302-1:2013EN 302-1:2013 (E) 6 1 Scope This European Standard specifies a method for determining the shear strength of adhesive bonds in close c

29、ontact glue line and thick glue line. It is suitable for the following applications: a) for assessing the compliance of adhesives with EN 301, EN 15425 and prEN 16254; b) for assessing the suitability and quality of adhesives for load-bearing timber structures. This test is intended primarily to obt

30、ain performance data for the classification of adhesives for load-bearing timber structures according to their suitability for use in defined climatic environments. This method is not intended for use to provide for structural design, and does not necessarily represent the performance of the bonded

31、member in service. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (

32、including any amendments) applies. EN 301, Adhesives, phenolic and aminoplastic, for load-bearing timber structures Classification and performance requirements EN 923:2005+A1:2008, Adhesives Terms and definitions ISO 5893, Rubber and plastics test equipment Tensile, flexural and compression types (c

33、onstant rate of traverse) Specification ISO 6344-2, Coated abrasives Grain size analysis Part 2: Determination of grain size distribution of macrogrits P12 to P220 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 923:2005+A1:2008 and the following appl

34、y. 3.1 glue line adhesive layer between the wood members 3.2 thick glue line glue line of nominal thickness in the range of 0,3 mm to 2,0 mm at the time of bonding Note 1 to entry: Thick glue lines are achieved by using spacers, grooves or similar devices with a thickness of 0,3 mm to 2,0 mm when tw

35、o plain members are glued together. 3.3 close contact glue line glue line of thickness maximum 0,1 mm BS EN 302-1:2013EN 302-1:2013 (E) 7 Note 1 to entry: Close contact glue line is achieved by pressing together two plane wood members with a clamping pressure of (0,8 0,1) N/mm without additional gro

36、oves, spacers or similar devices. 4 Symbols A bonded test surface, in mm; fvshear strength, in N/mm; Fmaxthe applied load at failure, in N; h depth of groove for thick glue line, 0,3 mm, 0,5 mm, 1,0 mm or 2,0 mm; angle between the annual growth rings and bonded surface, 30 to 85; l1length of test pi

37、eces, (150 5) mm; l2length of overlap (length of tested surface), (10,0 0,1) mm; l3width of groove for thick glue line, 14 mm; b width of test pieces, (20,0 0,1) mm; t thickness of panel for close contact glue line, (5,0 0,1) mm; t + h thickness of panel outside the grooves for thick glue line, in m

38、m. 5 Principle The shear strength of adhesive bonds is determined by applying a longitudinal tensile force to a single lap joint with close contact or thick glue lines between two rectangular wooden adherends made of beech (Fagus sylvatica L). The joints are loaded to rupture. 6 Apparatus The testin

39、g machine shall be either: a) capable of maintaining a constant rate of loading of (2,0 0,5) kN/min; or b) capable of maintaining constant crosshead speed as described in ISO 5893. The jaws of the testing machine shall grip the test pieces firmly and prevent slippage during loading. The grip shall b

40、e fixed in hinged manner. 7 Method 7.1 Preparation of panels By planing, prepare a sufficient number (see 7.4) of panels to be bonded, with or without 14 mm wide grooves as shown in Figure 1, from an untreated straight-grained board of beech (Fagus sylvatica L.) with a density of (700 50) kg/m at (1

41、2 1) % moisture content. Ensure that the angle, , between the growth rings and the surface to be bonded, see Figure 3 a), is between 30 and 85. BS EN 302-1:2013EN 302-1:2013 (E) 8 Cut the panels across the direction of the grain to a length of at least 300 mm with the necessary allowance for cross-c

42、utting (saw blade thickness) and along the grain to a width of at least 130 mm with the necessary allowance for the width of cut as shown in Figure 1. For tests on close contact glue lines, use two panels of (5,0 0,1) mm. For tests on thick glue lines, use one (5,0 0,1) mm thick panel and one (5,0 0

43、,1)+h mm thick panel. Make grooves with a depth h between 0,3 mm and 2,0 mm and a width of approximately 14 mm that end 5 mm from the side edges (see Figure 1). Condition the panels at a temperature of (20 2) C and (65 5) % RH, referred to subsequently as “the standard climate”. Dimensions in millim

44、eters Key h depth of groove for thick glue line b width of test pieces, (20,0 0,1) mm l1length of test pieces, (150 5) mm l3width of groove for thick glue line, 14 mm (l3=0 for close contact glue lines) t thickness of panel for close contact glue line, (5,0 0,1) mm t + h thickness of panel outside t

45、he grooves for thick glue line, in mm Figure 1 Example of a bonded panel marked for division into individual test pieces 7.2 Preparation of the bonded assemblies 7.2.1 Wood adherends and bonding procedure Prepare and bond the assemblies in standard climate using the requested glue line thickness. No

46、t more than 24 h before bonding, either lightly plane or lightly sand each surface to be bonded (using an abrasive paper of grain size P100 as defined in ISO 6344-2). Remove any dust carefully. Do not touch or soil the prepared surfaces. Comply with the adhesive manufacturers instructions regarding

47、the processing conditions, including the mixing of adhesive with the hardener, the spreading of the adhesive mix, the open and closed assembly time and duration of the assembly pressure, and report them in the test report. For thick glue lines, only adhesives BS EN 302-1:2013EN 302-1:2013 (E) 9 whos

48、e components have been previously mixed are suitable. After adhesive application, and before pressure application, the board shall be put together as shown in the lower part of Figure 1 and in Figure 2. Bond the panels at standard climate with a clamping pressure of (0,8 0,1) N/mm uniformly distribu

49、ted over the bonded surface, or as recommended by the adhesive manufacturer. 7.2.2 Close contact glue Bond two 5 mm thick panels as shown in Figure 1 under pressure to produce a 10 mm thick bonded assembly. The panels shall be assembled with the correct orientation of the annual growth rings. This can be achieved by assembling as shown in Figure 2 and the lower part of Figure 3 a). Figure 2 Bonding of panels with close contact joint 7.2.3 Thick glue lines

展开阅读全文
相关资源
  • BS ISO IEC 29150-2011 Information technology Security techniques Signcryption《信息技术 安全技术 签密》.pdfBS ISO IEC 29150-2011 Information technology Security techniques Signcryption《信息技术 安全技术 签密》.pdf
  • BS ISO IEC 15408-1-2009 Information technology - Security techniques - Evaluation criteria for IT Security - Introduction and general model《信息技术 安全技术 IT安全评价准则 一.pdfBS ISO IEC 15408-1-2009 Information technology - Security techniques - Evaluation criteria for IT Security - Introduction and general model《信息技术 安全技术 IT安全评价准则 一.pdf
  • BS ISO 7295-1988+A1-2014 Tyre valves for aircraft Interchangeability dimensions《飞机轮胎汽门嘴 互换性尺寸》.pdfBS ISO 7295-1988+A1-2014 Tyre valves for aircraft Interchangeability dimensions《飞机轮胎汽门嘴 互换性尺寸》.pdf
  • BS ISO 15118-1-2013 Road vehicles Vehicle to grid communication interface General information and use-case definition《道路车辆 车辆到电力通讯接口 通用信息和使用案例定义》.pdfBS ISO 15118-1-2013 Road vehicles Vehicle to grid communication interface General information and use-case definition《道路车辆 车辆到电力通讯接口 通用信息和使用案例定义》.pdf
  • BS ISO 13765-2-2004 Refractory mortars - Determination of consistency using the reciprocating flow table method《耐熔灰浆 使用往复流动表法测定一致性》.pdfBS ISO 13765-2-2004 Refractory mortars - Determination of consistency using the reciprocating flow table method《耐熔灰浆 使用往复流动表法测定一致性》.pdf
  • BS ISO 10998-2008+A1-2014 Agricultural tractors Requirements for steering《农业拖拉机 操纵要求》.pdfBS ISO 10998-2008+A1-2014 Agricultural tractors Requirements for steering《农业拖拉机 操纵要求》.pdf
  • BS Z 9-1998 Space data and information transfer systems - Advanced orbiting systems - Networks and data links - Architectural specification《空间数据和信息传输系统 高级轨道系统 网络和数据链接 结构规范》.pdfBS Z 9-1998 Space data and information transfer systems - Advanced orbiting systems - Networks and data links - Architectural specification《空间数据和信息传输系统 高级轨道系统 网络和数据链接 结构规范》.pdf
  • BS Z 7-1998 Space data and information transfer systems - ASCII encoded English《空间数据和信息传输系统 ASCII 编码英语》.pdfBS Z 7-1998 Space data and information transfer systems - ASCII encoded English《空间数据和信息传输系统 ASCII 编码英语》.pdf
  • BS Z 5-1997 Space data and information transfer systems - Standard formatted data units - Control authority procedures《航天数据和信息发送系统 标准格式数据单元 控制授权程序》.pdfBS Z 5-1997 Space data and information transfer systems - Standard formatted data units - Control authority procedures《航天数据和信息发送系统 标准格式数据单元 控制授权程序》.pdf
  • BS Z 4-1997 Space data and information transfer systems - Standard formatted data units - Structure and construction rules《航天数据和信息传输系统 标准格式数据单元 结构和构造规则》.pdfBS Z 4-1997 Space data and information transfer systems - Standard formatted data units - Structure and construction rules《航天数据和信息传输系统 标准格式数据单元 结构和构造规则》.pdf
  • 猜你喜欢
    相关搜索

    当前位置:首页 > 标准规范 > 国际标准 > BS

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1