1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 4531-901:2012Aerospace series Connectors, optical, circular,single and multipin, coupledby triple start threaded ring Flush contactsPart 901: Filler plugs Product standardB
2、S EN 4531-901:2012 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 4531-901:2012.The UK participation in its preparation was entrusted to TechnicalCommittee ACE/6, Aerospace avionic electrical and fibre optictechnology.A list of organizations represented on this
3、 committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2012. Published by BSI StandardsLimited 2012ISBN 978 0 580 75709 9ICS 49.0
4、60Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 May 2012.Amendments issued since publicationDate Text affectedBS EN 4531-901:2012EUROPEAN STANDARD NORME EUROP
5、ENNE EUROPISCHE NORM EN 4531-901 May 2012 ICS 49.060 English Version Aerospace series - Connectors, optical, circular, single and multipin, coupled by triple start threaded ring - Flush contacts - Part 901: Filler plugs - Product standard Srie arospatiale - Connecteurs optiques circulaires accouplem
6、ent par bague filete trois filets - Contacts affleurants - Partie 901: Obturateur dtanchit - Norme de produit Luft- und Raumfahrt - Optische Rundsteckverbinder mit dreigngiger Schraubkupplung - Bndige Kontakte - Teil 901: Blindstopfen - Produktnorm This European Standard was approved by CEN on 10 Se
7、ptember 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be
8、 obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to t
9、he CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxemb
10、ourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN A
11、ll rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 4531-901:2012: EBS EN 4531-901:2012EN 4531-901:2012 (E) 2 Contents Page Foreword 3g31g3 Scope 4g32g3 Normative references 4g33g3 Terms and definitions .4g34g3 Requirements .4g3BS EN 4531-9
12、01:2012EN 4531-901:2012 (E) 3 Foreword This document (EN 4531-901:2012) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the
13、 approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by November 2012, an
14、d conflicting national standards shall be withdrawn at the latest by November 2012. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. Ac
15、cording to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,
16、Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 4531-901:2012EN 4531-901:2012 (E) 4 1 Scope This European Standard specifies the characteristics of filler plugs (male and
17、 female) in the family of circular connectors with triple start threaded coupling. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For und
18、ated references, the latest edition of the referenced document (including any amendments) applies. EN 4531-001, Aerospace series Connectors, optical, circular, single and multipin, coupled by triple start threaded ring Flush contacts Part 001: Technical specification 3 Terms and definitions For the
19、purposes of this document, the terms and definitions given in EN 4531-001 apply. 4 Requirements 4.1 Configuration, dimensions, tolerances and mass 4.1.1 Configuration Configuration shall be in accordance with Figure 1 and Figure 2. 4.1.2 Dimensions, tolerances and mass Dimensions shall conform to Fi
20、gure 1, Figure 2, Table 1 and Table 2. All dimensions are in millimetres. Tolerances, see Table 1 and Table 2. The mass is in accordance with Table 1 and Table 2. BS EN 4531-901:2012EN 4531-901:2012 (E) 5 Figure 1 Filler plug male (type code P) Table 1 Dimensions, tolerances and mass (type code P) A
21、 B C D E F G H J Mass gmax. max. max. max. max. max. 0.1 max. max. max. 3,8 30,5 4,7 5,5 4,15 17,0 4,6 3,5 4,9 0,42 Figure 2 Filler plug female (type code S) Table 2 Dimensions, tolerances and mass (type code S) A B C D E F G H J K L Mass g max. max. max. max. max. max. 0,1 max. max. max. max. max.
22、3,8 38,0 4,7 5,5 4,15 17,0 4,6 3,5 4,9 24,3 2,85 0,45 BS EN 4531-901:2012EN 4531-901:2012 (E) 6 4.2 Material See Table 3. Table 3 Material Type code Insert Material S FemaleElastomer P Male 4.3 Operating temperature range The operating temperature ranges are: at long term (1 000 h) 65 C to 125 C; at
23、 short term (100 h) 65 C to 150 C. 4.4 Implementation See Figure 3. Filler plug for male insert Filler plug for female insert Figure 3 BS EN 4531-901:2012EN 4531-901:2012 (E) 7 4.5 Designation EXAMPLE Description block FILLER PLUG Identification block EN4531-901S Number of the basic standard Type co
24、de (see Table 3) 4.6 Marking Not applicable. 4.7 Technical specification See EN 4531-001. This page deliberately left blankThis page deliberately left blankBSI is the independent national body responsible for preparing British Standards and other standards-related publications, information and servi
25、ces. It presents the UK view on standards in Europe and at the international level. BSI is incorporated by Royal Charter. British Standards and other standardisation products are published by BSI Standards Limited.British Standards Institution (BSI)raising standards worldwideBSI389 Chiswick High Roa
26、d London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards and PASs are periodically updated by amendment or revision. Users of British Standards and PASs should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our prod
27、ucts and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using British Standards would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside frontcover. Similary for PASs, please notify BSI Customer Services.Te
28、l: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers BSI Subscribing Members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of British Standards and PASs.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standards
29、You may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the website addition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response
30、 to orders for international standards, BSI will supply the British Standard implementation of the relevant international standard, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, Europeanand international standards through its Knowledge Centr
31、e.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: BSI Subscribing Members are kept up to date with standards developments and receive substantial discounts on the purchase priceof standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002 F
32、ax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards and PASs via British Standards Online can be found at information about British Standards is available on the BSI website at www.bsi- the data, software and documentation set out in all British Standards and ot
33、her BSI publications are the property of and copyrighted by BSI, or some person or entity that own copyright in the information used (such as the international standardisation bodies) has formally licensed such information to BSI for commerical publication and use. Except as permitted under the Copy
34、right, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the
35、 standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Department.Tel: +44 (0)20 8996 7070Email:
