1、BRITISH STANDARDBS EN 12151:2007Machinery and plants for the preparation of concrete and mortar Safety requirementsThe European Standard EN 12151:2007 has the status of a British StandardICS 91.220g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59
2、g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 12151:2007This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 December 2007 BSI 2007ISBN 978 0 580 57945 5National forewordThis British Stan
3、dard is the UK implementation of EN 12151:2007.The UK participation in its preparation was entrusted by Technical Committee B/513, Construction equipment and plant and site safety, to Panel B/513/-/8, Concrete plant.A list of organizations represented on this committee can be obtained on request to
4、its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.Amendments issued since publicationAmd. No. Date CommentsEUROPEAN
5、STANDARDNORME EUROPENNEEUROPISCHE NORMEN 12151November 2007ICS 91.220English VersionMachinery and plants for the preparation of concrete and mortar- Safety requirementsMachines et centrales pour la prparation du bton et dumortier - Prescriptions de scuritMaschinen und Anlagen zur Bereitung von Beton
6、 undMrtel - SicherheitsanforderungenThis European Standard was approved by CEN on 13 October 2007.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-
7、date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder th
8、e responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary
9、, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue d
10、e Stassart, 36 B-1050 Brussels 2007 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 12151:2007: EEN 12151:2007 (E) 2 Contents Page Foreword5 Introduction .6 1 Scope 7 2 Normative references 7 3 Terms and definitions .9 4 List of sign
11、ificant hazards 12 5 Safety requirements and/or protective measures14 5.1 Common requirements for all groups of machines .14 5.1.1 High pressure fluid injection hazard from hydraulic or pneumatic systems 14 5.1.2 Electrical hazards 14 5.1.3 Main switches and control panels .14 5.1.4 Emergency stop.1
12、5 5.1.5 Thermal hazard 15 5.1.6 Hazard generated by noise .15 5.1.7 Ergonomic design15 5.1.8 Weather conditions15 5.1.9 Permanent means of access 15 5.1.10 Fire protection16 5.1.11 Assembly 16 5.1.12 Electrical Magnetic Compatibility (EMC) of machines.16 5.1.13 Further requirements 16 5.2 Specific r
13、equirements relating to different types of machines.16 5.2.1 General16 5.2.2 Small mobile tipping drum mixers for domestic and industrial use (see Annex B) .16 5.2.3 All other mixers, e.g. tipping drum mixers (stationary), trough-, pan-, through-flow mixers (see Annex B) .20 5.2.4 Ground tipping sys
14、tems (see Annex B) 24 5.2.5 Radial scrapers and radius lift arms (see Figures B.2 to B.6) 25 5.2.6 Skip hoist system (see Figure B.8) 26 5.2.7 Dosing equipment (see Figure B.9 in Annex B) .28 5.2.8 Aggregate distribution chute (see Figure B.10) .30 5.2.9 Mobile mixing plant (see figure B.13 in Annex
15、 B) 31 5.2.10 Waste concrete reprocessing plant (see Figures B.20, B.21 and B.22).31 6 Verification of safety requirements and/or protective measures .32 7 Information for use 33 7.1 Instruction handbook 33 7.1.1 General33 7.1.2 Small mobile tipping drum mixers for domestic and industrial use 33 7.1
16、.3 All other mixers, e.g. tipping drum mixers (stationary), trough mixers, pan mixers, through-flow mixers .34 7.1.4 Ground tipping systems .34 7.1.5 Scraper radius, bridge and dragline plant 34 7.1.6 Skip hoists35 7.1.7 Dosing equipment35 7.1.8 Aggregate distribution chute35 7.1.9 Mobile mixing pla
17、nt .35 7.1.10 Waste concrete reprocessing plant.35 7.1.11 Information of machine marking, see 7.236 EN 12151:2007 (E) 3 7.2 Marking .36 7.2.1 General36 7.2.2 Specifically for hydraulic and pneumatic systems 36 7.2.3 Specifically for electrical equipment .37 7.2.4 Specifically for internal combustion
18、 engine.37 7.2.5 Specifically for control stations, working platforms, accesses and lifting equipment37 7.2.6 Mixer with an electrical class II motor.37 7.2.7 Underground buffer stock area37 Annex A (normative) Stability, ground surface, headroom and access requirements .38 A.1 Ground surface and he
19、adroom of operation areas38 A.2 General access 38 A.3 Stability test of small mobile tipping drum mixers 39 Annex B (informative) Illustration of mixer and plants .40 Annex C (normative) Noise test code .60 C.1 Scope 60 C.2 Sound power level determination 60 C.2.1 Mixers60 C.2.2 Plants 61 C.3 Emissi
20、on sound pressure level determination.62 C.3.1 Mixers62 C.3.2 Plants 62 C.4 Installation conditions.62 C.5 Operating conditions.62 C.6 Information to be recorded.63 C.7 Information to be reported63 C.8 Declaration of noise emission values .63 Annex ZA (informative) Relationship between this European
21、 Standard and the Essential Requirements of EU Directive 98/37/EC .64 Annex ZB (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 2006/42/EC .65 Bibliography66 EN 12151:2007 (E) 4 Figures Figure A.1 Tipping drum mixer (plan view) 39 Figure A.2 Ti
22、pping drum mixer (side view).39 Figure B.1 Small mobile tipping drum mixer 40 Figure B.2 Example of a dragline scraper and a star plant41 Figure B.3 Example of a scraper radius plant (front view).42 Figure B.4 Protection walls and safety barrier for plant with one radius lift arm43 Figure B.5 Protec
23、tion walls and safety barrier for plant with one or more radius lift arm(s) 44 Figure B.6 Radius lift arm with buckets45 Figure B.7 Example of a ground tipping hopper 46 Figure B.8 Example of a skip hoist system 47 Figure B.9 Dosing equipment of a batching plant48 Figure B.10 Aggregate distribution
24、system (e.g. distribution shoot) 49 Figure B.11 Example of concrete production plant with the plant featuring in-line hopper aggregate storage equipment50 Figure B.12 Example of a vertical mixing plant fed by conveyor belt or bucket elevator.51 Figure B.13 Example of a mobile mixing .52 Figure B.14
25、Tipping drum mixer.52 Figure B.15 Chute discharge mixer53 Figure B.16 Reversing drum mixer 53 Figure B.17 Trough mixer .54 Figure B.18 Stationary pan with concentrically placed rotating paddles55 Figure B.19 Example of a through-flow mixer56 Figure B.20 Waste concrete reprocessing plant (above groun
26、d) 57 Figure B.21 Waste concrete reprocessing plant (plant partly underground) .58 Figure B.22 Waste concrete reprocessing plant 59 Figure B.23 Dimensions of outlet hopper of through-flow mixers 59 Figure C.1 Microphone array on the hemisphere (12 microphone positions)61 EN 12151:2007 (E) 5 Foreword
27、 This document (EN 12151:2007) has been prepared by Technical Committee CEN/TC 151 “Construction equipment and building material machines Safety”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical t
28、ext or by endorsement, at the latest by May 2008, and conflicting national standards shall be withdrawn at the latest by May 2008. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of E
29、U Directive(s). For relationship with EU Directive(s), see informative Annex ZA and Annex ZB, which are an integral part of this document. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard:
30、 Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EN 12151
31、:2007 (E) 6 Introduction This document is a type C standard as stated in EN ISO 12100-1:2003. The machinery concerned and the extent to which hazards, hazardous situations and events are covered are indicated in the scope of this document. When provisions of this type C standard are different from t
32、hose which are stated in type A or B standards, the provisions of this type C standard take precedence over the provisions of the other standards, for machines that have been designed and built according to the provisions of this type C standard. The road traffic law for each country remains unaffec
33、ted by this standard. EN 12151:2007 (E) 7 1 Scope 1.1 This document applies for machinery and plants for the preparation of concrete and mortar as defined in 3.1. This document specifies the requirements for the design of: a) batching and mixing installations for concrete and mortar; b) powered mixe
34、rs for concrete and mortar, including for storage and handling; c) waste fresh concrete reprocessing plant. It does not include requirements relevant to truck mixers. The machinery may be static or it may be capable of being moved to an alternative position. 1.2 This document deals with all signific
35、ant hazards, hazardous situations and events relevant to machinery and plant for the preparation of concrete and mortar, when they are used as intended and under the conditions foreseen by the manufacturer (see Clause 4). The exceptions are explosion hazards when using flammable or explosive materia
36、ls that are significant but not dealt with. This document specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards. Maintenance is dealt with but not noise during maintenance. 1.3 This document is not applicable to machinery and plants which are
37、manufactured before the date of publication of this document by CEN. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced do
38、cument (including any amendments) applies. EN 294:1992, Safety of machinery Safety distances to prevent danger zones being reached by the upper limbs EN 349:1993, Safety of machinery Minimum gaps to avoid crushing of parts of the human body EN 360:2002, Personal protective equipment against falls fr
39、om a height Retractable type fall arresters EN 361:2002, Personal protective equipment against falls from a height Full body harnesses EN 363:2002, Personal protective equipment against falls from a height Fall arrest systems EN 547-1:1996, Safety of machinery Human body measurements Part 1: Princip
40、les for determining the dimensions required for openings for whole body access into machinery EN 547-2:1996, Safety of machinery Human body measurements Part 2: Principles for determining the dimensions required for access openings EN 547-3:1996, Safety of machinery Human body measurements Part 3: A
41、nthropometric data EN 574:1996, Safety of machinery Two-hand control devices Functional aspects Principles for design EN 614-1:2006, Safety of machinery Ergonomic design principles Part 1: Terminology and general principles EN 617:2001, Continuous handling equipment and systems Safety and EMC requir
42、ements for the equipment for the storage of bulk materials in silos, bunkers, bins and hoppers EN 12151:2007 (E) 8 EN 618:2002, Continuous handling equipment and systems Safety and EMC requirements for equipment for mechanical handling of bulk materials except fixed belt conveyors EN 620:2002, Conti
43、nuous handling equipment and systems Safety and EMC requirements for fixed belt conveyors for bulk materials EN 795:1996, Protection against falls from a height Anchor devices Requirements and testing EN 811:1996, Safety of machinery Safety distances to prevent danger zones being reached by the lowe
44、r limbs EN 894-1:1997, Safety of machinery Ergonomic requirements for the design of displays and control actuators Part 1: General principles for human interactions with displays and control actuators EN 894-2:1997, Safety of machinery Ergonomics requirements for the design of displays and control a
45、ctuators Part 2: Displays EN 953:1997, Safety of machinery Guards General requirements for the design and construction of fixed and movable guards EN 954-1:1996, Safety of machinery Safety-related parts of control systems Part 1: General principles for design EN 982:1996, Safety of machinery Safety
46、requirements for fluid power systems and their components Hydraulics EN 983:1996, Safety of machinery Safety requirements for fluid power systems and their components Pneumatics EN 999:1998, Safety of machinery The positioning of protective equipment in respect of approach speeds of parts of the hum
47、an body EN 1050:1996, Safety of machinery Principles for risk assessment EN 1088:1995, Safety of machinery Interlocking devices associated with guards Principles for design and selection EN 12198-1:2000, Safety of machinery Assessment and reduction of risks arising from radiation emitted by machiner
48、y Part 1: General principles EN 13309:2000, Construction machinery Electromagnetic compatibility of machines with internal electrical power supply EN 60204-1:2006, Safety of machinery Electrical equipment of machines Part 1: General requirements (IEC 60204-1:2005, modified) EN 60204-32:1998, Safety
49、of machinery Electrical equipment of machines Part 32: Requirements for hoisting machines (IEC 60204-32:1998) EN 60335-1:2002, Household and similar electrical appliances Safety Part 1: General requirements (IEC 60335-1:2001, modified) EN 60335-2-69:2003, Household and similar electrical appliances Safety Part 2-69: Particular requirements for wet and dry vacuum cleaners, including power brush, for industrial and commercial use (
