BS EN 16466-3-2013 Vinegar Isotopic analysis of acetic acid and water 18O-IRMS analysis of water in wine vinegar《醋 醋酸和水的同位素分析 酒醋中水的18O-IRMS分析》.pdf

上传人:jobexamine331 文档编号:573881 上传时间:2018-12-13 格式:PDF 页数:14 大小:999.46KB
下载 相关 举报
BS EN 16466-3-2013 Vinegar Isotopic analysis of acetic acid and water 18O-IRMS analysis of water in wine vinegar《醋 醋酸和水的同位素分析 酒醋中水的18O-IRMS分析》.pdf_第1页
第1页 / 共14页
BS EN 16466-3-2013 Vinegar Isotopic analysis of acetic acid and water 18O-IRMS analysis of water in wine vinegar《醋 醋酸和水的同位素分析 酒醋中水的18O-IRMS分析》.pdf_第2页
第2页 / 共14页
BS EN 16466-3-2013 Vinegar Isotopic analysis of acetic acid and water 18O-IRMS analysis of water in wine vinegar《醋 醋酸和水的同位素分析 酒醋中水的18O-IRMS分析》.pdf_第3页
第3页 / 共14页
BS EN 16466-3-2013 Vinegar Isotopic analysis of acetic acid and water 18O-IRMS analysis of water in wine vinegar《醋 醋酸和水的同位素分析 酒醋中水的18O-IRMS分析》.pdf_第4页
第4页 / 共14页
BS EN 16466-3-2013 Vinegar Isotopic analysis of acetic acid and water 18O-IRMS analysis of water in wine vinegar《醋 醋酸和水的同位素分析 酒醋中水的18O-IRMS分析》.pdf_第5页
第5页 / 共14页
点击查看更多>>
资源描述

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 16466-3:2013Vinegar Isotopic analysis of acetic acid and waterPart 3: O-IRMS analysis of water in wine vinegar8BS EN 16466-3:2013 BRITISH STANDARDNational forewordThis Brit

2、ish Standard is the UK implementation of EN 16466-3:2013. The UK participation in its preparation was entrusted to TechnicalCommittee AW/-/2, Food Technical Committee Chairmen.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not

3、purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2013. Published by BSI Standards Limited 2013ISBN 978 0 580 73668 1 ICS 67.220.10 Compliance with a British Standard cannot confer immunity from legal o

4、bligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 January 2013.Amendments issued since publicationDate T e x t a f f e c t e dBS EN 16466-3:2013EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 16466-3 January 2013 ICS 67.220.1

5、0 English Version Vinegar - Isotopic analysis of acetic acid and water - Part 3: 18O-IRMS analysis of water in wine vinegar Vinaigre - Analyse isotopique de lacide actique et de leau - Partie 3: Analyse SMRI-18O de leau dans le vinaigre de vin Essig - Isotopenanalyse von Essig und Wasser - Teil 3: 1

6、8O-IRMS-Analyse von Wasser in Weinessig This European Standard was approved by CEN on 3 November 2012. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

7、Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by tra

8、nslation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finl

9、and, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATI

10、ON COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 16466-3:2013: E BS EN 16466-3:2013EN 16466-3:2013 (E) 2 Cont

11、ents Page Foreword . 3 Introduction 4 1 Scope 5 2 Normative references . 5 3 Principle 5 4 Reagents . 5 4.1 Carbon dioxide . 5 4.2 Carbon dioxide used for equilibration 5 5 Apparatus . 5 6 Procedure . 6 6.1 General . 6 6.2 Manual method . 6 6.3 Use of an automatic exchange apparatus . 6 6.4 Manual p

12、reparation manual and automatic equilibration and analysis with a dual inlet IRMS 7 6.5 Use of an automatic equilibration apparatus coupled to a continuous flow system 7 6.6 Calculation and expression of the results 7 7 Precision . 8 7.1 Repeatability . 8 7.2 Reproducibility . 8 8 Test report 8 Anne

13、x A (informative) Results of the collaborative study (2009) 9 Bibliography 10 BS EN 16466-3:2013EN 16466-3:2013 (E) 3 Foreword This document (EN 16466-3:2013) has been based on an international collaborative study of the method published in Analytica Chimica Acta 649 (2009) 98-105, and organised und

14、er the auspices of the Permanent International Vinegar Committee (CPIV, Brussels). This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by July 2013, and conflicting national standards shall be withdrawn

15、at the latest by July 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. The European standard, Vinegar Isotopic analysis of acetic

16、 acid and water, consists of the following parts: Part 1: 2H-NMR analysis of acetic acid; Part 2: 13C-IRMS analysis of acetic acid; Part 3: 18O-IRMS analysis of water. According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following countries are bound to impl

17、ement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania

18、, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 16466-3:2013EN 16466-3:2013 (E) 4 Introduction Wine vinegar is defined by the European Regulations 479/2008 and 491/2009 as the product obtained exclusively from the acetous fermentation of wine, which is in turn

19、defined as the product exclusively obtained from the alcoholic fermentation of fresh grapes, whether crushed or not, or of grape must. In accordance with this, it is clear that the production of wine vinegar by fermenting dried grapes and rehydrating with tap water is not allowed by European Regulat

20、ions. The isotopic analysis of water from vinegar by 18O-IRMS enables the distinction of wine vinegar and vinegars from fermented dried grapes which have been rehydrated with water 1, and more generally helps to check the authenticity of wine vinegar. BS EN 16466-3:2013EN 16466-3:2013 (E) 5 1 Scope

21、This European Standard specifies an isotopic method to control the authenticity of wine vinegar. This method is applicable on wine vinegar in order to characterise the 18O/16O ratio of water, and allows differentiating wine vinegar from vinegars made from raisins or alcohol vinegar. NOTE The Oxygen

22、18 isotopic analysis of water from vinegar is based on a similar method already normalised for wine analysis 2. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the e

23、dition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. Not applicable. 3 Principle The 18O/16O ratio of water from vinegar is determined on CO2gas after equilibration of reference CO2gas with vinegar water according to the foll

24、owing isotopic exchange reaction: OHOOCOHOC1621816182216+(1)After equilibration the carbon dioxide in the gaseous phase is used for analysis by means of Isotopic Ratio Mass Spectrometry (IRMS) where the 18O/16O isotopic ratio is determined on the CO2resulting from the equilibration. 4 Reagents All r

25、eagents and consumables used shall meet stated requirements of the used method / apparatus (as specified by the manufacturer). However, all reagents and consumables can be replaced by items with similar performance. 4.1 Carbon dioxide For analysis, used as secondary reference gas for the determinati

26、on of 13C/12C ratio. Purity 5.2 minimum. 4.2 Carbon dioxide used for equilibration Depending on the instrument, this gas could be the same as 4.1 or in the case of continuous flow systems cylinders containing gas mixture helium-carbon dioxide can also be used 5 Apparatus All equipments and materials

27、 used shall meet stated requirements of the used method/apparatus (as specified by the manufacturer). However, all equipments and materials can be replaced by items with similar performance. 5.1 Vials with septa appropriate for the used system. BS EN 16466-3:2013EN 16466-3:2013 (E) 6 5.2 Volumetric

28、pipettes with appropriate tips. 5.3 Temperature controlled system to carry out the equilibration at constant temperature, typically within 1 C. 5.4 Vacuum pump (if needed for the used system). 5.5 Autosampler (if needed for the used system). 5.6 Syringes for sampling (if needed for the used system).

29、 5.7 GC Column to separate CO2from other elementary gases (if needed for the used system). 5.8 Water removal device (e.g. cryo-trap, selective permeable membranes). 6 Procedure 6.1 General The descriptions that follow refer to procedures generally used for the determination of the 18O/16O isotopic r

30、atios by means of equilibration of water with a CO2working standard and the subsequent measurement by IRMS. These procedures can be altered according to changes of equipment and instrumentation provided by the manufacturers as various kinds of equilibration devices are available, implying various co

31、nditions of operation. Two main technical procedures can be used for introduction of CO2into the IRMS either through a dual inlet system or using a continuous flow system. The description of all these technical systems and of the corresponding conditions of operation is not possible. All values give

32、n for volumes, temperatures, pressures and time periods are only indicative. Appropriate values shall be obtained from specifications provided by the manufacturer and/or determined experimentally. 6.2 Manual method A defined volume of the sample/standard is transferred into a flask using a pipette.

33、The flask is then attached tightly to the manifold. Each manifold is cooled down to below 80 C to deep-freeze the samples (manifold equipped with capillary opening tubes do not require this freezing step). Subsequently, the whole system is evacuated. After reaching a stable vacuum the gaseous CO2wor

34、king standard is allowed to expand into the various flasks. For the equilibration process each manifold is placed in a temperature controlled waterbath typically at 25 C ( 1 C) for 12 h (overnight). It is crucial that the temperature of the water-bath is kept constant and homogeneous. After the equi

35、libration process is completed, the resulting CO2is transferred from the flasks to the sample side bellow of the dual inlet system. The measurements are performed by comparing several times the ratios of the CO2contained in the sample side and the standard side (CO2reference standard gas) of the dua

36、l inlet. This approach is repeated till the last sample of the sequence has been measured. 6.3 Use of an automatic exchange apparatus A defined volume of the sample/standard is transferred into a vial using a pipette. The sample vials are attached to the equilibration system and cooled down to below

37、 80 C to deep-freeze the samples (systems equipped with capillary opening tubes do not require this freezing step). Subsequently, the whole system is evacuated. After reaching a stable vacuum the gaseous CO2working standard is expanded into the vials. Equilibrium is reached at a temperature of typic

38、ally (22 1) C after a minimum period of 5 h and with moderate agitation (if BS EN 16466-3:2013EN 16466-3:2013 (E) 7 available). Since the equilibration duration depends on various parameters (e.g. the vial geometry, temperature, applied agitation .), the minimum equilibrium time should be determined

39、 experimentally. After the equilibration process is completed, the resulting CO2is transferred from the vials to the sample side bellow of the dual inlet system. The measurements are performed by comparing several times the ratios of the CO2contained in the sample side and the standard side (CO2refe

40、rence standard gas) of the dual inlet. This approach is repeated till the last sample of the sequence has been measured. 6.4 Manual preparation manual and automatic equilibration and analysis with a dual inlet IRMS A defined volume of sample / standard (e.g. 200 l) is introduced into a vial using a

41、pipette. The open vials are then placed in a closed chamber filled with the CO2used for equilibration (4.2). After several purges to eliminate any trace of air, the vials are closed and then placed on the thermostated plate of the sample changer. The equilibration is reached after at least 8 h at 40

42、 C. Once the process of equilibration completed, the CO2obtained is dried and then transferred into the sample side of the dual inlet introduction system. The measurements are performed by comparing several times the ratios of the CO2contained in the sample side and the standard side (CO2reference s

43、tandard gas) of the dual inlet. This approach is repeated until the last sample of the sequence has been measured. 6.5 Use of an automatic equilibration apparatus coupled to a continuous flow system A defined volume of the sample/standard is transferred into a vial using a pipette. The sample vials

44、are placed into a temperature controlled tray. Using a gas syringe the vials are flushed with mixture of He and CO2. The CO2remains in the headspace of the vials for equilibration. Equilibrium is reached at a temperature typically of (30 1) C after a minimum period of 18 h. After the equilibration p

45、rocess is completed the resulting CO2is transferred by means of the continuous flow system into the ion source of the mass spectrometer. CO2reference gas is also introduced into the IRMS by means of the continuous flow system. The measurement is carried out according to a specific protocol for each

46、kind of equipment. 6.6 Calculation and expression of the results The purpose of the method is to measure the 18O/16O ratio of water extracted from vinegar. The 18O/16O isotope ratio can be expressed by its deviation from a working reference. The isotopic deviation of oxygen 18 (18O) is then calculat

47、ed on a delta scale per thousand () by comparing the results obtained for the sample to be measured with those for a working reference previously calibrated on the basis of the primary international reference (V.SMOW2). The 18O values (in ) are expressed in relation to the working reference as follo

48、ws: ( ) ( )( )18 16 18 16sample standard (V.SMOW2)1818 16(V.SMOW2)standardO/ O O/ OOOO/RR R= (2) where Rsampleand Rstandardare respectively the 18O/16O isotope ratios of the sample and of the standard. Between two measurements of the standard working sample, the variation, and therefore the correcti

49、on to be applied to the results obtained from the samples, may be assumed to be linear. The standard working sample shall be measured at the beginning and at the end of all sample series. A correction can then be calculated for each sample according to its position in the sequence using linear interpolation. BS EN 16466-3:2013EN 16466-3:2013 (E) 8 7 Precision 7.1 Repeatability In the collaborative study organised in 2009 (see Annex A: Results of the collaborative study (2009), the average repeatability limit (r = 2,8 x sr) of the 18

展开阅读全文
相关资源
  • BS ISO IEC 29150-2011 Information technology Security techniques Signcryption《信息技术 安全技术 签密》.pdfBS ISO IEC 29150-2011 Information technology Security techniques Signcryption《信息技术 安全技术 签密》.pdf
  • BS ISO IEC 15408-1-2009 Information technology - Security techniques - Evaluation criteria for IT Security - Introduction and general model《信息技术 安全技术 IT安全评价准则 一.pdfBS ISO IEC 15408-1-2009 Information technology - Security techniques - Evaluation criteria for IT Security - Introduction and general model《信息技术 安全技术 IT安全评价准则 一.pdf
  • BS ISO 7295-1988+A1-2014 Tyre valves for aircraft Interchangeability dimensions《飞机轮胎汽门嘴 互换性尺寸》.pdfBS ISO 7295-1988+A1-2014 Tyre valves for aircraft Interchangeability dimensions《飞机轮胎汽门嘴 互换性尺寸》.pdf
  • BS ISO 15118-1-2013 Road vehicles Vehicle to grid communication interface General information and use-case definition《道路车辆 车辆到电力通讯接口 通用信息和使用案例定义》.pdfBS ISO 15118-1-2013 Road vehicles Vehicle to grid communication interface General information and use-case definition《道路车辆 车辆到电力通讯接口 通用信息和使用案例定义》.pdf
  • BS ISO 13765-2-2004 Refractory mortars - Determination of consistency using the reciprocating flow table method《耐熔灰浆 使用往复流动表法测定一致性》.pdfBS ISO 13765-2-2004 Refractory mortars - Determination of consistency using the reciprocating flow table method《耐熔灰浆 使用往复流动表法测定一致性》.pdf
  • BS ISO 10998-2008+A1-2014 Agricultural tractors Requirements for steering《农业拖拉机 操纵要求》.pdfBS ISO 10998-2008+A1-2014 Agricultural tractors Requirements for steering《农业拖拉机 操纵要求》.pdf
  • BS Z 9-1998 Space data and information transfer systems - Advanced orbiting systems - Networks and data links - Architectural specification《空间数据和信息传输系统 高级轨道系统 网络和数据链接 结构规范》.pdfBS Z 9-1998 Space data and information transfer systems - Advanced orbiting systems - Networks and data links - Architectural specification《空间数据和信息传输系统 高级轨道系统 网络和数据链接 结构规范》.pdf
  • BS Z 7-1998 Space data and information transfer systems - ASCII encoded English《空间数据和信息传输系统 ASCII 编码英语》.pdfBS Z 7-1998 Space data and information transfer systems - ASCII encoded English《空间数据和信息传输系统 ASCII 编码英语》.pdf
  • BS Z 5-1997 Space data and information transfer systems - Standard formatted data units - Control authority procedures《航天数据和信息发送系统 标准格式数据单元 控制授权程序》.pdfBS Z 5-1997 Space data and information transfer systems - Standard formatted data units - Control authority procedures《航天数据和信息发送系统 标准格式数据单元 控制授权程序》.pdf
  • BS Z 4-1997 Space data and information transfer systems - Standard formatted data units - Structure and construction rules《航天数据和信息传输系统 标准格式数据单元 结构和构造规则》.pdfBS Z 4-1997 Space data and information transfer systems - Standard formatted data units - Structure and construction rules《航天数据和信息传输系统 标准格式数据单元 结构和构造规则》.pdf
  • 猜你喜欢
    相关搜索

    当前位置:首页 > 标准规范 > 国际标准 > BS

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1