1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationSpecifications for particular types of winding wiresPart 17: Polyvinyl acetal enamelled rectangular copper wire, class 105BS EN 60317-17:2010National forewordThis British Standar
2、d is the UK implementation of EN 60317-17:2010. It isidentical to IEC 60317-17:2010. It supersedes BS EN 60317-17:1996 which iswithdrawn.The UK participation in its preparation was entrusted to Technical CommitteeGEL/55, Winding wires.A list of organizations represented on this committee can be obta
3、ined onrequest to its secretary.This publication does not purport to include all the necessary provisions of acontract. Users are responsible for its correct application. BSI 2010ISBN 978 0 580 67179 1ICS 29.060.10Compliance with a British Standard cannot confer immunity fromlegal obligations.This B
4、ritish Standard was published under the authority of the StandardsPolicy and Strategy Committee on 30 June 2010.Amendments issued since publicationAmd. No. Date Text affectedBRITISH STANDARDBS EN 60317-17:2010EUROPEAN STANDARD EN 60317-17 NORME EUROPENNE EUROPISCHE NORM May 2010 CENELEC European Com
5、mittee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Management Centre: Avenue Marnix 17, B - 1000 Brussels 2010 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC me
6、mbers. Ref. No. EN 60317-17:2010 E ICS 29.060.10 Supersedes EN 60317-17:1994 + A1:1998 + A2:2005English version Specifications for particular types of winding wires - Part 17: Polyvinyl acetal enamelled rectangular copper wire, class 105 (IEC 60317-17:2010) Spcifications pour types particuliers de f
7、ils de bobinage - Partie 17: Fil de section rectangulaire en cuivre maill avec actal de polyvinyle, classe 105 (CEI 60317-17:2010) Technische Lieferbedingungen fr bestimmte Typen von Wickeldrhten - Teil 17: Flachdrhte aus Kupfer, lackisoliert mit Polyvinylazetat, Klasse 105(IEC 60317-17:2010) This E
8、uropean Standard was approved by CENELEC on 2010-05-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical refere
9、nces concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC me
10、mber into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungar
11、y, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 60317-17:2010EN 60317-17:2010 - 2 - Foreword The text of document 55/1180/FDIS, future edition 3 of IEC 6
12、0317-17, prepared by IEC TC 55, Winding wires, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 60317-17 on 2010-05-01. This European Standard supersedes EN 60317-17:1994 + A1:1998 + A2:2005. The main change with respect to EN 60317-17:1994 is listed below: Clause 20:
13、 reference to the transformer oil resistance test method in EN 60851-4. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patent rights. The following dat
14、es were fixed: latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2011-02-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2013-05-01 Annex ZA has been added by
15、CENELEC. _ Endorsement notice The text of the International Standard IEC 60317-17:2010 was approved by CENELEC as a European Standard without any modification. _ BS EN 60317-17:2010- 3 - EN 60317-17:2010 Annex ZA (normative) Normative references to international publications with their corresponding
16、 European publications The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE When an international
17、 publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. Publication Year Title EN/HD Year IEC 60317-0-2 + A1 + A2 1997 1999 2005 Specifications for particular types of winding wires - Part 0-2: General requirements - Enamelled rectangular copper wire E
18、N 60317-0-2 + A1 + A2 1998 2000 2005 IEC 60851-4 + A1 + A2 1996 1997 2005 Winding wires - Test methods Part 4: Chemical properties EN 60851-4 + A1 + A2 1996 1997 2005 BS EN 60317-17:2010 2 60317-17 IEC:2010 CONTENTS INTRODUCTION.5 1 Scope.6 2 Normative references .6 3 Terms, definitions and general
19、notes on methods of test and appearance 7 3.1 Terms and definitions 7 3.2 General notes on methods of test7 3.3 Appearance.7 4 Dimensions 7 5 Electrical resistance .7 6 Elongation 7 7 Springiness 7 8 Flexibility and adherence7 8.1 Mandrel winding test .7 8.2 Stretching test.7 9 Heat shock .8 10 Cut-
20、through 8 11 Resistance to abrasion .8 12 Resistance to solvents8 13 Breakdown voltage .8 14 Continuity of insulation .8 15 Temperature index .8 16 Resistance to refrigerants.8 17 Solderability .8 18 Heat or solvent bonding8 19 Dielectric dissipation factor.8 20 Resistance to transformer oil 9 21 Lo
21、ss of mass 9 23 Pin hole test .9 30 Packaging 9 Table 1 Mandrel winding 7 BS EN 60317-17:201060317-17 IEC:2010 5 INTRODUCTION This part of IEC 60317 is one of a series which deals with insulated wires used for windings in electrical equipment. The series has three groups describing 1) winding wires
22、and test methods (IEC 60851); 2) specifications for particular types of winding wire (IEC 60317); 3) packaging of winding wires (IEC 60264). BS EN 60317-17:2010 6 60317-17 IEC:2010 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES Part 17: Polyvinyl acetal enamelled rectangular copper wire, class
23、 105 1 Scope This part of IEC 60317 specifies the requirements of enamelled rectangular copper winding wire of class 105 with a sole coating based on polyvinyl acetal resin, which may be modified providing it retains the chemical identity of the original resin and meets all specified wire requiremen
24、ts. NOTE A modified resin is a resin that has undergone a chemical change, or contains one or more additives to enhance certain performance or application characteristics. Class 105 is a thermal class that requires a minimum temperature index of 105 and a heat shock temperature of at least 155 C. Th
25、e temperature in degrees Celsius corresponding to the temperature index is not necessarily that at which it is recommended that the wire be operated and this will depend on many factors, including the type of equipment involved. The range of nominal conductor dimensions covered by this standard is w
26、idth: min. 2,00 mm max. 16,00 mm; thickness: min. 0,80 mm max. 5,60 mm. Wires of grade 1 and grade 2 are included in this specification and apply to the complete range of conductors. The specified combinations of width and thickness as well as the specified ratio width/thickness are given in IEC 603
27、17-0-2. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60317-0-2:1997
28、, Specifications for particular types of winding wires Part 0-2: General requirements Enamelled rectangular copper wire Amendment 1 (1999) Amendment 2 (2005) IEC 60851-4:1996, Methods of test for winding wires Part 4: Chemical properties Amendment 1 (1997) Amendment 2 (2005) BS EN 60317-17:201060317
29、-17 IEC:2010 7 3 Terms, definitions and general notes on methods of test and appearance 3.1 Terms and definitions For terms and definitions, see 3.1 of IEC 60317-0-2. In case of inconsistencies between IEC 60317-0-2 and this standard, IEC 60317-17 shall prevail. 3.2 General notes on methods of test
30、For general notes on methods of test, see 3.2 of IEC 60317-0-2. In case of inconsistencies between IEC 60317-0-2 and this standard, IEC 60317-17 shall prevail. 3.3 Appearance See 3.3 of IEC 60317-0-2. 4 Dimensions See Clause 4 of IEC 60317-0-2. 5 Electrical resistance See Clause 5 of IEC 60317-0-2.
31、6 Elongation See Clause 6 of IEC 60317-0-2. 7 Springiness See Clause 7 of IEC 60317-0-2. 8 Flexibility and adherence 8.1 Mandrel winding test The coating shall show no crack after the wire has been bent flatwise and edgewise on a mandrel with a diameter as specified in Table 1. Table 1 Mandrel windi
32、ng Wire bent on Mandrel diameter Width Sizes up to and including 10 mm Sizes over 10 mm 2 width 3 width Thickness All dimensions 2 thickness 8.2 Stretching test The wire shall be stretched by 20 %. BS EN 60317-17:2010 8 60317-17 IEC:2010 The distance of loss of adhesion shall be less than 1x width.
33、9 Heat shock See Clause 9 of IEC 60317-0-2, where the minimum heat shock temperature shall be 155 C. 10 Cut-through Test inappropriate. 11 Resistance to abrasion Test inappropriate. 12 Resistance to solvents See Clause 12 of IEC 60317-0-2. 13 Breakdown voltage See Clause 13 of IEC 60317-0-2, where t
34、he elevated temperature shall be 105 C. 14 Continuity of insulation Test inappropriate. 15 Temperature index See Clause 15 of IEC 60317-0-2, where the minimum temperature index shall be 105. 16 Resistance to refrigerants Test inappropriate. 17 Solderability Test inappropriate. 18 Heat or solvent bon
35、ding Test inappropriate. 19 Dielectric dissipation factor Test inappropriate. BS EN 60317-17:201060317-17 IEC:2010 9 20 Resistance to transformer oil Test according to Clause 6 of IEC 60851-4 appropriate. Test requirements are under consideration. 21 Loss of mass Test inappropriate. 23 Pin hole test
36、 Test inappropriate. 30 Packaging See Clause 30 of IEC 60317-0-2. _ BS EN 60317-17:2010This page deliberately left blankThis page deliberately left blankBSI is the independent national body responsible for preparing British Standardsand other standards-related publications, information and services.
37、 It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.British Standards Institution (BSI)raising standards worldwideBSI Group Headquarters389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards are upda
38、ted by amendment or revision. Users of British Stan-dards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and serv-ices. We would be grateful if anyone finding an inaccuracy or ambiguity whileusing this British
39、 Standard would inform the Secretary of the technical com-mittee responsible, the identity of which can be found on the inside frontcover.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers Members an individual updating service called PLUS which ensuresthat subscribers automatically receive
40、 the latest editions of standards.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the website addition all orders for BSI, international and foreign standards publicationscan
41、 be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, it is BSI policy tosupply the BSI implementation of those that have been publishedas British Standards, unless otherwise requested.Information on standard
42、sBSI provides a wide range of information on national, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: Various BSI electronic information services are also available whichgive details on all its products and services. Tel: +44
43、(0)20 8996 7111 Fax: +44 (0)20 8996 7048Email: BSI Subscribing Members are kept up to date with standardsdevelopments and receive substantial discounts on the purchase priceof standards. For details of these and other benefits contact Membership Ad-ministration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)
44、20 8996 7001 Email: Information regarding online access to British Standards via BritishStandards Online can be found at information about BSI is available on the BSI website at www.bsi- subsists in all BSI publications. BSI also holds the copyright,in the UK, of the publications of the internatio
45、nal standardization bodies. Ex-cept as permitted under the Copyright, Designs and Patents Act 1988 no ex-tract may be reproduced, stored in a retrieval system or transmitted in anyform or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This do
46、es not preclude the freeuse, in the course of implementing the standard of necessary details such assymbols, and size, type or grade designations. If these details are to be usedfor any other purpose than implementation then the prior written permissionof BSI must be obtained. Details and advice can be obtained from the Copy-right & Licensing Manager.Tel: +44 (0)20 8996 7070Email:
