1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationElectrical equipment for measurement, control and laboratory use EMC requirementsPart 2-2: Particular requirements Test configurations, operational conditions and performance cri
2、teria for portable test, measuring and monitoring equipment used in low-voltage distribution systems(IEC 61326-2-2:2012)BS EN 61326-2-2:2013National forewordThis British Standard is the UK implementation of EN 61326-2-2:2013. It is identical to IEC 61326-2-2:2012. It supersedes BS EN 61326-2-2:2006,
3、 which will be withdrawn on 6 November 2015.The UK participation in its preparation was entrusted by Technical Committee GEL/65, Measurement and control, to Subcommittee GEL/65/1, System considerations.A list of organizations represented on this committee can be obtained on request to its secretary.
4、This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2013.Published by BSI Standards Limited 2013.ISBN 978 0 580 70406 2 ICS 25.040.40; 33.100.01Compliance with a British Standard
5、 cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 28 February 2013.Amendments issued since publicationAmd. No. Date Text affectedBRITISH STANDARDBS EN 61326-2-2:2013EUROPEAN STANDARD EN 61326-2-2 N
6、ORME EUROPENNE EUROPISCHE NORM January 2013 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Management Centre: Avenue Marnix 17, B - 1000 Brussels 2013 CENELEC - All rights of exploitatio
7、n in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 61326-2-2:2013 E ICS 17.220; 25.040.40; 33.100 Supersedes EN 61326-2-2:2006 English version Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 2-2: Particular requirements - Tes
8、t configurations, operational conditions and performance criteria for portable test, measuring and monitoring equipment used in low-voltage distribution systems (IEC 61326-2-2:2012) Matriel lectrique de mesure, de commande et de laboratoire - Exigences relatives la CEM - Partie 2-2: Exigences partic
9、ulires - Configurations dessai, conditions de fonctionnement et critres daptitude la fonction des matriels portatifs dessai, de mesure et de surveillance utiliss dans des systmes de distribution basse tension (CEI 61326-2-2:2012) Elektrische Mess-, Steuer-, Regel- und Laborgerte EMV-Anforderungen Te
10、il 2-2: Besondere Anforderungen Prfanordnung, Betriebsbedingungen und Leistungsmerkmale fr ortsvernderliche Prf-, Mess- und berwachungsgerte fr den Gebrauch in Niederspannungs-Stromversorgungsnetzen (IEC 61326-2-2:2012) This European Standard was approved by CENELEC on 2012-11-06. CENELEC members ar
11、e bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to
12、the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Manag
13、ement Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ire
14、land, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 61326-2-2:2013EN 61326-2-2:2013 Foreword The text of document 65A/642/FDIS, future edition 2 of IEC 61326-2-2, p
15、repared by SC 65A, “Systemaspects“, of IEC TC 65, “Industrial-process measurement, control and automation“ was submitted to theIEC-CENELEC parallel vote and approved by CENELEC as EN 61326-2-2:2013. The following dates are fixed: latest date by which the document has to be implemented at national le
16、vel bypublication of an identical national standard or by endorsement (dop) 2013-08-06 latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2015-11-06 This document supersedes EN 61326-2-2:2006. EN 61326-2-2:2013 includes the following significant tech
17、nical changes with respect to EN 61326-2-2:2006: Update with respect to EN 61326-1:2013. EN 61326-2-2:2013 is to be used in conjunction with EN 61326-1:2013 and follows the same numberingof clauses, subclauses, tables and figures. When a particular subclause of EN 61326-1 is not mentioned in this pa
18、rt, that subclause applies as far asis reasonable. When this standard states “addition”, “modification” or “replacement”, the relevant text inEN 61326-1 is to be adapted accordingly. NOTE The following numbering system is used: subclauses, tables and figures that are numbered starting from 101 are a
19、dditional to those in EN 61326-1; unless notes are in a new subclause or involve notes in EN 61326-1, they are numbered starting from 101 includingthose in a replaced clause or subclause; additional annexes are lettered AA, BB, etc. Attention is drawn to the possibility that some of the elements of
20、this document may be the subject ofpatent rights. CENELEC and/or CEN shall not be held responsible for identifying any or all such patentrights. This document has been prepared under a mandate given to CENELEC by the European Commissionand the European Free Trade Association, and supports essential
21、requirements of EU Directive(s). For the relationship with EU Directive(s) see informative Annex ZZ, which is an integral part of thisdocument. Endorsement notice The text of the International Standard IEC 61326-2-2:2012 was approved by CENELEC as a EuropeanStandard without any modification. BS EN 6
22、1326-2-2:2013EN 61326-2-2:2013 Annex ZA (normative) Normative references to international publicationswith their corresponding European publications The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated referenc
23、es, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HDapplies. Annex ZA of EN 61326-1:2013 a
24、pplies, except as follows: Publication Year Title EN/HD Year Addition: IEC 61326-1 2012 Electrical equipment for measurement, controland laboratory use - EMC requirements - Part 1: General requirements EN 61326-1 2013 IEC 61557 Series Electrical safety in low voltage distributionsystems up to 1 000
25、V a.c. and 1 500 V d.c. - Equipment for testing, measuring ormonitoring of protective measures EN 61557 Series BS EN 61326-2-2:2013EN 61326-2-2:2013 Annex ZZ (informative) Coverage of Essential Requirements of EU Directives This European Standard has been prepared under a mandate given to CENELEC by
26、 the EuropeanCommission and the European Free Trade Association and within its scope the standard coversprotection requirements of Annex I, Article 1 of the EC Directive 2004/108/EC. Compliance with this standard provides one means of conformity with the specified essentialrequirements of the Direct
27、ives concerned. NOTE Other requirements and other EU Directives may be applicable to the products falling within the scope ofthis standard. BS EN 61326-2-2:201361326-2-2 IEC:2012 CONTENTS 1 Scope . . 5 2 Normative references . 5 3 Terms and definitions . 5 4 General . 6 5 EMC test plan . 6 5.1 Gener
28、al . 6 5.2 Configuration of EUT during testing . 6 5.3 Operation conditions of EUT during testing . 8 5.4 Specification of functional performance . 8 5.5 Test description . 8 6 Immunity requirements . 8 6.1 Conditions during the tests . . 8 6.2 Immunity test requirements . 8 6.3 Random aspects. . 9
29、6.4 Performance criteria . 9 7 Emission requirements . 9 8 Test results and test report . . 9 9 Instructions for use 9 Figure 101 Test set-up for portable test, measuring and monitoring equipment based on IEC 61000-4-3 . 7 Figure 102 Example of connection details for voltage measurements . 7 Figure
30、103 Example of connection details for current measurements . 8 BS EN 61326-2-2:201361326-2-2 IEC:2012 5 ELECTRICAL EQUIPMENT FOR MEASUREMENT, CONTROL AND LABORATORY USE EMC REQUIREMENTS Part 2-2: Particular requirements Test configurations, operational conditions and performance criteria for portabl
31、e test, measuring and monitoring equipment used in low-voltage distribution systems 1 Scope In addition to the scope of IEC 61326-1, this part of IEC 61326 specifies more detailed test configurations, operational conditions and performance criteria for equipment covered by Annex A of IEC 61326-1 whi
32、ch is: used for testing, measuring or monitoring of protective measures in low-voltage distribution systems, and; powered by battery and/or from the circuit measured, and portable. Examples of such EUT include, but are not limited to, voltage detectors, insulation testers, earth continuity testers,
33、earth resistance testers, loop impedance testers, “residual-current-device-testers” (RCD-testers) and phase sequence testers as defined in IEC 61557. NOTE Particular EMC requirements for equipment covered by IEC 61557-8 and IEC 61557-9 are given in IEC 61326-2-4. The manufacturer specifies the envir
34、onment for which the product is intended to be used and/or select the appropriate test level specifications of IEC 61326-1. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references
35、, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. Clause 2 of IEC 61326-1:2012 applies, except as follows: Addition: IEC 61326-1:2012, Electrical equipment for measurement, control and laboratory use EMC requir
36、ements Part 1: General requirements IEC 61557 (all parts), Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. Equipment for testing, measuring or monitoring of protective measures 3 Terms and definitions For the purposes of this document, the terms and definiti
37、ons given in IEC 61326-1 and IEC 60050-161 apply. BS EN 61326-2-2:2013 6 61326-2-2 IEC:2012 4 General Clause 4 of IEC 61326-1 applies. 5 EMC test plan 5.1 General Subclause 5.1 of IEC 61326-1 applies. 5.2 Configuration of EUT during testing Subclause 5.2 of IEC 61326-1 applies, except as follows: Ad
38、dition: 5.2.4.101 Test and measurement I/O ports Electrostatic discharge shall be applied to the housing, to the terminals of the EUT and to the coupling planes, but not to the inner pins of shielded port or cable connectors (for example, BNC, D-subminiature, IEEE 488 (GPIB), RS232, IEEE 1284-B (par
39、allel printer port), etc.). For the test according to IEC 61000-4-3 the following conditions shall be met. Test and measurement ports shall be connected with test leads recommended or supplied with the EUT. Where the test leads are unspecified, typical test leads shall be used. The test leads shall
40、be connected and arranged in a typical configuration for each operation mode, according to Figure 101. If the test leads recommended or supplied are longer than 1 m, each one should be bundled up so that the test or measurement object is in a (horizontal) distance of 1 m to the EUT. The test leads s
41、hall be arranged 0,1 m apart in a horizontal position on the test table. BS EN 61326-2-2:201361326-2-2 IEC:2012 7 EUT Test object EM-clamp(s)aAE Uniform area AE Top view Incident electromagnetic field Absorber lined shielded enclosure IEC 1835/12 aEM-clamp(s) (if necessary). Figure 101 Test set-up f
42、or portable test, measuring and monitoring equipment based on IEC 61000-4-3 Auxiliary equipment (AE) required for generating or monitoring the test object signal shall be connected according to Figure 101 via EM-clamps if necessary as described in IEC 61000-4-6, Figure A.3. Voltage measurements shal
43、l be made with a 1 000 100 resistor (test object) connected in series with one of the test leads as shown in Figure 102. For other measurements, the test object shall be specified by the manufacturer and documented in the test report. EUT Test object EM-clamp(s) 0,1 mAEbDNa1 m IEC 1836/12 aDecouplin
44、g network (if necessary). bFor example, voltage source. Figure 102 Example of connection details for voltage measurements BS EN 61326-2-2:2013 8 61326-2-2 IEC:2012 Current measurements shall be made with a 100 10 resistor (test object) connected in parallel with the test leads as shown in Figure 103
45、. EUT Test object EM-clamp(s) 0,1 mAEbDNa1 m IEC 1837/12 aDecoupling network (if necessary). bFor example, current source. Figure 103 Example of connection details for current measurements 5.3 Operation conditions of EUT during testing Subclause 5.3 of IEC 61326-1 applies, except as follows: Additio
46、n: 5.3.101 Operational conditions Test and measurement equipment shall be set to the most sensitive ranges or combination of ranges unless other ranges are known to provide worst-case immunity results within normal application. Each function of multifunctional equipment shall be tested separately. 5
47、.4 Specification of functional performance Subclause 5.4 of IEC 61326-1 applies. 5.5 Test description Subclause 5.5 of IEC 61326-1 applies. 6 Immunity requirements 6.1 Conditions during the tests Subclause 6.1 of IEC 61326-1 applies. 6.2 Immunity test requirements Subclause 6.2 of IEC 61326-1 is rep
48、laced by the following: Table A.1 of IEC 61326-1 gives the immunity requirements for equipment covered by the scope of this part. Addition: BS EN 61326-2-2:201361326-2-2 IEC:2012 9 6.2.101 Electromagnetic field If the maximum dimension of the equipment enclosure is 0,3 m, the test is performed from
49、only one side in accordance with Figure 101 and noted in the test report. 6.3 Random aspects Subclause 6.3 of IEC 61326-1 applies. 6.4 Performance criteria Subclause 6.4 of IEC 61326-1 applies, except as follows: Replacement for 6.4.2 of IEC 61326-1: 6.4.2.101 Performance criterion A During testing, normal performance within the specification limits. This includes that variations are allowed outside the maximum intrinsic error documented in the t
