1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS EN ISO 14527-1:2000 Th
2、e European Standard EN ISO 14527-1:1999 has the status of a British Standard ICS 83.080.10 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Plastics Urea-formaldehyde and urea/melamine- formaldehyde powder moulding compounds (UF- and UF/MF-PMCs) Part 1: Designation system and b
3、asis for specificationsThis British Standard, having been prepared under the direction of the Sector Committee for Materials and Chemicals, was published under the authority of the Standards Committee and comes into effect on 15 January 2000 BSI 01-2000 ISBN 0 580 35876 3 BS EN ISO 14527-1:2000 Amen
4、dments issued since publication Amd. No. Date Comments National foreword This British Standard is the English language version of EN ISO 14527-1:1999. It is identical with ISO 14527-1:1999. The UK participation in its preparation was entrusted to Technical Committee PRI/42, Fibre reinforced thermose
5、tting plastics and prepregs, which has the responsibility to: aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European
6、 developments and promulgate them in the UK. A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references Attention is drawn to the fact that CEN and CENELEC Standards normally include an annex which lists normative references to international p
7、ublications with their corresponding European publications. The British Standards which implement these international or European publications may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the
8、 BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summ
9、ary of pages This document comprises a front cover, an inside front cover, the EN ISO title page, the EN ISO foreword page, the ISO title page, pages ii and iii, a blank page, pages 1 to 6, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicates when the
10、document was last issued.EN ISO 14527-1:1999 Referencenumber ISO14527-1:1999(E) INTERNATIONAL STANDARD ISO 14527-1 Firstedition 1999-11-15 PlasticsUrea-formaldehydeand urea/melamine-formaldehydepowder mouldingcompounds(UF-and UF/MF-PMCs) Part1: Designationsystemandbasisfor specifications Plastiques
11、Poudres mouler base dure-formaldhyde et dure/mlamine-formaldhyde (UF- et UF/MF-PMC) Partie 1: Systme de dsignation et base de spcification EN ISO 14527-1:1999ISO-725411:(9991E) ISO9991 Allrgihtsresvrede.lnUesstorehwisescepfieid,noraptofthisilbupctaoinmaybeudorpercedorutziliedinnayformorbynaynaems,el
12、ectnoric ormecinahcal,inclidungtohpociypongnadmicrfoilm,wituohteprmissioninwritingfromeitehrISOattherddaessleboworISOsmemebrydob inthectnuoryofthertseuqee.r ISOcirypohgtfofice aCsesoptale56 121-HC1veneGa20 leT.+41224790111 aFx+41223741097 E-mailcirypothgiso.ch Webwww.iso.ch ii DPFdcsilremia ihTsPDFf
13、ilemayctnoainemeddebdtyfepaces.InaccnadrocewithAebodslicensinglopicy,thisfilemaybepirntedorivewedubtslahlton beidetedlnuessthetyfepaceswhichareemeddebdraelicensedtonadintslaledonthecomputerfrepormingtheideting.Inodwlnidaongthis feli,trapiesaccepttierehnthesersnoptilibiyofontinfrnignigAebodslicsnenig
14、lopicy.hTeISOtneCarlSecterairatacceptsnollibaiityinthis .aera AbodeisatdaremarkofAbodeStsyemsInctaropro.de teDailsofthesfotwraepudorctsusedtocrtaeetihsPDFfilecanbefnuodintheGarenelInfolerativetothefile;theP-FDcerationrapamteers weretpoimizedforpirtning.Evreycraeahseebntakentoensruethatthefileissuitl
15、baeforusebyISOmemebridobse.Inthelnuikleyetnev tahtaplboremleratingtoitisfdnuo,lpaeseifnormthetneCarlSecterairatattheserddasgivenlebow. EN ISO 14527-1:1999ISO14527-1:1999(E)iii Foreword ISO(theInternationalOrganizationforStandardization)isaworldwidefederationofnationalstandardsbodies(ISO memberbodies
16、).TheworkofpreparingInternationalStandardsisnormallycarriedoutthroughISOtechnical committees.Eachmemberbodyinterestedinasubjectforwhichatechnicalcommitteehasbeenestablishedhas therighttoberepresentedonthatcommittee.Internationalorganizations,governmentalandnon-governmental,in liaisonwithISO,alsotake
17、partinthework.ISOcollaboratescloselywiththeInternationalElectrotechnical Commission(IEC)onallmattersofelectrotechnicalstandardization. InternationalStandardsaredraftedinaccordancewiththerulesgivenintheISO/IECDirectives,Part3. DraftInternationalStandardsadoptedbythetechnicalcommitteesarecirculatedtot
18、hememberbodiesforvoting. PublicationasanInternationalStandardrequiresapprovalbyatleast75%ofthememberbodiescastingavote. AttentionisdrawntothepossibilitythatsomeoftheelementsofthispartofISO14527maybethesubjectof patentrights.ISOshallnotbeheldresponsibleforidentifyinganyorallsuchpatentrights. Internat
19、ionalStandardISO14527-1waspreparedbyTechnicalCommitteeISO/TC61, Plastics, Subcommittee SC12, Thermosetting materials. Afteratransitionperiodof,atthemost,fouryears,thethreepartsofISO14527(seebelow),togetherwiththe threepartsofISO14528,willreplaceISO2112:1990,ofwhichtheyconstituteatechnicalrevision. I
20、SO14527consistsofthefollowingparts,underthegeneraltitle Plastics Urea-formaldehyde and urea/melamine-formaldehyde powder moulding compounds (UF- and UF/MF-PMCs): Part 1: Designation system and basis for specifications Part 2: Preparation of test specimens and determination of properties Part 3: Requ
21、irements for selected moulding compounds EN ISO 14527-1:1999EN ISO 14527-1:1999INTERNATIONAL STANDARD ISO 14527-1:1999(E) ISO 9991 All irhgts seredevr 1 Plastics Urea-formaldehyde and urea/melamine-formaldehyde powder moulding compounds (UF- and UF/MF-PMCs) Part 1: Designation system and basis for s
22、pecifications 1 Scope 1.1 This part of ISO 14527 establishes a data block system for the designation of urea-formaldehyde and urea/melamine-formaldehyde powder moulding compounds (UF- and UF/MF-PMCs). 1.2 The various types of UF- and UF/MF-PMC are differentiated from each other by a classification s
23、ystem based on information about the filler/reinforcement type and content, the intended method of processing, any special properties and those of the special properties used specifically for designation purposes (designatory properties). 1.3 This part of ISO 14527 is applicable to all UF- and UF/MF
24、-PMCs ready for normal use in the form of powder, granules or ground material. 1.4 It is not intended to imply that materials having the same designation necessarily give the same performance. This part of ISO 14527 does not provide engineering data, performance data or data on processing conditions
25、 which may be required to specify a material for a particular application and/or method of processing. If such additional properties are required, they shall be determined in accordance with the test methods specified in ISO 14527-2, if suitable. 1.5 Whenever general requirement data, as covered by
26、ISO 14527-3, need to be indicated, this is also done using this data block system. 1.6 To ensure that code-letters and code-numbers remain unambiguous, and to avoid conflicts within the system, any new code-letters or code-numbers for use in data block 1, 2 or 3 shall be approved before use by the s
27、ecretariats of ISO/TC 61/SC 1, SC 12 and SC 13. 2 Normative references The following normative documents contain provisions which, through reference in this text, constitute provisions of this part of ISO 14527. For dated references, subsequent amendments to, or revisions of, any of these publicatio
28、ns do not apply. However, parties to agreements based on this part of ISO 14527 are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies. Mem
29、bers of ISO and IEC maintain registers of currently valid International Standards. ISO 75-2:1993, Plastics Determination of temperature of deflection under load Part 2: Plastics and ebonite. ISO 179-1: 1) , Plastics Determination of Charpy impact properties Part 1: Non-instrumented impact test. 1) T
30、o be published. (Revision of ISO 179:1993) EN ISO 14527-1:1999 1ISO -725411:(9991E) 2 ISO 9991 All irhgts seredevr ISO 472:1999, Plastics Vocabulary. ISO 1043-1:1997, Plastics Symbols and abbreviated terms Part 1: Basic polymers and their special characteristics. ISO 1043-2: 2) , Plastics Symbols an
31、d abbreviated terms Part 2: Fillers and reinforcing materials. ISO 2112:1990, Plastics Aminoplastic moulding materials Specification. ISO 14527-2:1999, Plastics Urea-formaldehyde and urea/melamine-formaldehyde powder moulding compounds (UF- and UF/MF-PMCs) Part 2: Preparation of test specimens and d
32、etermination of properties. ISO 14527-3:1999, Plastics Urea-formaldehyde and urea/melamine-formaldehyde powder moulding compounds (UF- and UF/MF-PMCs) Part 3: Requirements for selected moulding compounds. 3 Terms and definitions For the purposes of this part of ISO 14527, the terms and definitions g
33、iven in ISO 472 and ISO 14527-2 apply, plus the following: 3.1 powder moulding compound powder, granules or ground material capable of flowing freely through the feed systems of processing machines, as well as moulding compounds in the form of flakes which are normally not thought of as powders The
34、abbreviation for powder moulding compound is PMC by analogy with bulk moulding compound (BMC) and sheet moulding compound (SMC). 3.2 UF-PMC abbreviation for powder moulding compounds based on urea-formaldehyde resins for both injection and compression moulding 3.3 UF/MF-PMC abbreviation for powder m
35、oulding compounds based on a mixture of urea-formaldehyde and melamine- formaldehyde resins for both injection and compression moulding 4 Designation system 4.1 General The designation system defined in this part of ISO 14527 is based on the following standardized pattern: Designation Identity block
36、 Description ISO Individual-item block block Standard Data block 1 Data block 2 Data block 3 Data block 4 Data block 5 2) To be published. (Revision of ISO 1043-2:1988) EN ISO 14527-1:1999 2ISO -725411:(9991E) ISO 9991 All irhgts seredevr 3 The designation consists of an optional description block,
37、reading “PMC“, and an identity block comprising the International Standard number and an individual-item block. For unambiguous designation, the individual-item block is subdivided into five data blocks comprising the following information: Data block 1: Marking block Item 1: Identification of the b
38、asic polymer by its symbol, in accordance with ISO 1043-1; Item 2: Nature of the designatory reinforcement materials or fillers, in accordance with ISO 1043-2; Item 3: Form of the designatory reinforcement materials or fillers, in accordance with ISO 1043-2; Item 4: Nominal content of the designator
39、y reinforcement materials or fillers, in accordance with Table 1. Data block 2: Method of processing Method of processing for which the moulding compound is intended, designated in accordance with Table 2. Data block 3: Properties Item 1: Special properties, in accordance with Table 3; Item 2: Desig
40、natory property No. 1 impact strength determined in accordance with ISO 179-1; Item 3: Designatory property No. 2 temperature resistance determined in accordance with ISO 75-2. Data block 4: Further information, taken from an international, national or company standard. Data block 5 (optional): Addi
41、tional requirements The first character of the individual-item block shall be a hyphen. The data blocks shall be separated from each other by commas. If a data block is not used, this shall be indicated by an “X“ (= not applicable), but only if another block follows. For labelling purposes, and prov
42、ided no other blocks follow, the comma between blocks 1 and 2 can be omitted. There is no need to fill in data blocks if they are not required. 4.2 Data block 1 Item 1: After the hyphen, urea-formaldehyde or urea/melamine-formaldehyde powder moulding compounds shall be identified by the symbol UF or
43、 UF/MF, in accordance with ISO 1043-1. Mixtures and modifications shall be designated in accordance with ISO 1043-1:1997, subclauses 4 and 5. The following information shall be restricted to designatory fillers/reinforcements used in the material in question: Item 2: Nature of filler/reinforcement,
44、in accordance with Table 1. Item 3: Form of filler/reinforcement, in accordance with Table 1. Item 4: Nominal content (mass %) of filler/reinforcement, in accordance with Table 1. Note, in particular, the following: the same code-letters have different meanings when used for item 2 and item 3; whene
45、ver information needs to be indicated only for item 3, an “X“ ( = not applicable) is required for item 2. EN ISO 14527-1:1999 3ISO -725411:(9991E) 4 ISO 9991 All irhgts seredevr 4.3 Data block 2 In this data block, information about the method of processing is given using the code-letters specified
46、in Table 2. The code-letter used to indicate the intended method of processing in data block 2 shall be selected carefully. Certain brands of material can be processed in more than one way, e.g. either by compression moulding (Q) or by injection moulding (M). Such brands shall be designated “general
47、 purpose“ (G). The designation of special methods of processing shall be reserved for specially modified materials. Table 1 Code-letters and code-numbers used in data block 1 Nature of filler/reinforcement (in accordance with ISO 1043-2) Form of filler/reinforcement (in accordance with ISO 1043-2) P
48、ercentage content by mass, w % (m/m) C D E G K L1 L2 M P Q R S T W X Z Carbon Aluminium oxide trihydrate Clay Glass Calcium carbonate Cellulose Cotton Mineral Mica Silica Recycled material Synthetic organic Talc Wood Not specified Others B C D F G S X Z Balls; beads; spheres Chips; cuttings Fines; p
49、owder Fibre Ground Scale; flakes Not specified Others 05 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 w7 , 5 7,5u w 12,5 12,5u w 17,5 17,5u w 22,5 22,5u w 27,5 27,5u w 32,5 32,5u w 37,5 37,5u w 42,5 42,5u w 47,5 47,5u w 52,5 52,5u w 57,5 57,5u w 62,5 62,5u w 67,5 67,5u w 72,5 72,5u w 77,5 77,5u w 82,5 82,5u w 87,5 87,5u w 92,5 92,5u w 97,5 NOTE Mixtures of materials and/or forms may be indicated by combining the relevant codes using the sign “+“ and placing the whole between
