1、BSI Standards PublicationBS ISO 10889-7:2016Tool holders with cylindricalshankPart 7: Type F with taper seatBS ISO 10889-7:2016 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 10889-7:2016. It supersedes BS ISO 10889-7:2004 which is withdrawn. The UK participat
2、ion in its preparation was entrusted to Technical Committee MTE/18, Tools tips and inserts for cutting applications.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contrac
3、t. Users are responsible for its correct application. The British Standards Institution 2016.Published by BSI Standards Limited 2016ISBN 978 0 580 90327 4 ICS 25.060.20 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the auth
4、ority of the Standards Policy and Strategy Committee on 31 March 2016.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dBS ISO 10889-7:2016 ISO 2016Tool holders with cylindrical shank Part 7: Type F with taper seatPorte-outil queue cylindrique Partie 7: Porte-outil de type F
5、pour outils queue coniqueINTERNATIONAL STANDARDISO10889-7Third edition2016-03-15Reference numberISO 10889-7:2016(E)BS ISO 10889-7:2016ISO 10889-7:2016(E)ii ISO 2016 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2016, Published in SwitzerlandAll rights reserved. Unless otherwise specified, no p
6、art of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member
7、body in the country of the requester.ISO copyright officeCh. de Blandonnet 8 CP 401CH-1214 Vernier, Geneva, SwitzerlandTel. +41 22 749 01 11Fax +41 22 749 09 47copyrightiso.orgwww.iso.orgBS ISO 10889-7:2016ISO 10889-7:2016(E)Foreword iv1 Scope . 12 Normative references 13 Dimensions . 14 Designation
8、 35 Technical delivery conditions . 3Annex A (informative) Relationship between designations in this part of ISO 10889 and ISO 13399 . 4Bibliography 5 ISO 2016 All rights reserved iiiContents PageBS ISO 10889-7:2016ISO 10889-7:2016(E)ForewordISO (the International Organization for Standardization) i
9、s a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represe
10、nted on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop
11、 this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IE
12、C Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the
13、development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of
14、ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary informationThe committee responsible for this document is ISO/TC 29, Small t
15、ools, Subcommittee SC 2, Holding tools, adaptive items and interfaces.This third edition cancels and replaces the second edition (ISO 10889-7:2004), of which it constitutes a minor revision, notably with the addition of Annex A, which gives the relationship between the designations of this part of I
16、SO 10889 and the ISO 13399 series.ISO 10889 consists of the following parts, under the general title Tool holders with cylindrical shank: Part 1: Cylindrical shank, location bore Technical delivery conditions Part 2: Type A, shanks for tool holders of special designs Part 3: Type B with rectangular
17、radial seat Part 4: Type C with rectangular axial seat Part 5: Type D with more than one rectangular seat Part 6: Type E with cylindrical seat Part 7: Type F with taper seat Part 8: Type Z, accessoriesiv ISO 2016 All rights reservedBS ISO 10889-7:2016INTERNATIONAL STANDARD ISO 10889-7:2016(E)Tool ho
18、lders with cylindrical shank Part 7: Type F with taper seat1 ScopeThis part of ISO 10889 specifies dimensions, designations, and complementary technical delivery conditions for tool holders with taper seat of type F and with a cylindrical shank mounting system in accordance with ISO 10889-1.ISO 1088
19、9 is applicable to tool holders with cylindrical shank for machine tools with non-rotating tools, preferably for turning machines.For non-standardized tool holders with taper seat such as the tool holders shown in Figure 1, it is advisable to apply the corresponding specifications of this part of IS
20、O 10889.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including an
21、y amendments) applies.ISO 296, Machine tools Self-holding tapers for tool shanksISO 2768-1, General tolerances Part 1: Tolerances for linear and angular dimensions without individual tolerance indicationsISO 2768-2, General tolerances Part 2: Geometrical tolerances for features without individual to
22、lerance indicationsISO 10889-1, Tool holders with cylindrical shank Part 1: Cylindrical shank, location bore Technical delivery conditions3 DimensionsAll dimensions and tolerances are given in millimetres. Tolerancing is done according to ISO 8015. Tolerances not specified shall be of tolerance clas
23、s “m” in accordance with ISO 2768-1 and of class “H” in accordance with ISO 2768-2.Unspecified details shall be chosen appropriately.The dimensions of tool holders type F shall be in accordance with the dimensions shown in Figure 1 and given in Table 1.The relationship between the symbols of this pa
24、rt of ISO 10889 and the symbols according to ISO 13399 is given in Annex A. ISO 2016 All rights reserved 1BS ISO 10889-7:2016ISO 10889-7:2016(E)Dimensions in millimetresabcg597 0,02g597dg597dg597dg597 dg597 dlllhhKeyaCylindrical shank in accordance with ISO 10889-1.bInternal Morse taper, type BIK in
25、 accordance with ISO 296.cExternal coolant supply (closable).Figure 1 Taper seat type F tool holder for taper shanks with flat tangTable 1 Type F tool holder dimensionsDimensions in millimetresd1Internal Morse taper, type BIK No.d2d3d4d5h1h2l1l2l3l420 1 50 12,065 23 23 40 7a2515812,065 25 2523 482 1
26、7,780 5 27 3016812,065 28 30 27552 17,780 5 14a4028317,780 55 532,5 3622 633 23,825 58 6 14a4 31,267 68 7 80 5029817,780 55 535 3630 783 23,825 58 6 4 31,267 68 7 80 18aaThese sizes have a recess for taper shanks with flat tang up to the end face of the cylindrical shank. The design of slot is at th
27、e discretion of the manufacturer.2 ISO 2016 All rights reservedBS ISO 10889-7:2016ISO 10889-7:2016(E)d1Internal Morse taper, type BIK No.d2d3d4d5h1h2l1l2l3l460312323,825 58 642,5 3630 944 31,267 68 7 50 5 44,399 98 7 63 32a80415831,267 687 55 50 40 1045 44,399 98 aThese sizes have a recess for taper
28、 shanks with flat tang up to the end face of the cylindrical shank. The design of slot is at the discretion of the manufacturer.4 DesignationA type F tool holder with Morse taper seat in accordance with this part of ISO 10889 shall be designated by the following:a) “tool holder”;b) reference to this
29、 part of ISO 10889, i.e. ISO 10889-7;c) type (F);d) nominal diameter, d1, in millimetres;e) internal taper type;f) if applicable, hardened contact surface (H).EXAMPLE 1 A type F tool holder with a Morse taper seat, a nominal diameter, d1= 40 mm, and an internal taper, type BIK 3, is designated as fo
30、llows:Tool holder ISO 10889-7 - F - 40 - MT-BIK 3EXAMPLE 2 A type F tool holder with a Morse taper seat and nominal diameter, d1= 40 mm, an internal taper, type BIK 3, and hardened contact surface is designated as follows:Tool holder ISO 10889-7 - F - 40 - MT-BIK 3 H5 Technical delivery conditionsAs
31、 a complement to the requirements of ISO 10889-1, the following requirements also apply.The taper socket shall be hardened with a surface hardness of (56 04+) HRC and a depth of hardening of at least 0,5 mm.The taper angle tolerance class of taper socket shall be AT5 in accordance with ISO 296.Tool
32、holders can also be supplied with hardened contact surface.Table 1 (continued) ISO 2016 All rights reserved 3BS ISO 10889-7:2016ISO 10889-7:2016(E)Annex A (informative) Relationship between designations in this part of ISO 10889 and ISO 13399For the relationship between the symbols of this part of I
33、SO 10889 and the symbols according to ISO 13399, see Table A.1.Table A.1 Relationship between symbols in this part of ISO 10889 and ISO 13399Symbol in this part of ISO 10889Reference in this part of ISO 10889Property name in ISO 13399 seriesSymbol in ISO 13399 seriesReference in ISO 13399 series BSU
34、 coded1Figure 1 connection diameter machine sideDCONMS 71EBDBF5060E6d2Figure 1 flange diameter DF 71EC61D8A1771d3Figure 1 functional diameterDFC 7272379AD9C85d4Figure 1 body diameter DB 71ED6A9AF7D1Dd5Figure 1 l1Figure 1 protruding length LPR 71DCD394BB20El2Figure 1 flange thickness FLGT 71EEF538097
35、64l3Figure 1 shank length LS 71CF298870946l4Figure 1 h1Figure 1 OAHa RADH h2Figure 1 radial height RADH 726E3E86B5284aOAH is the “overall height” (code BSU 71D078EB73E87).4 ISO 2016 All rights reservedBS ISO 10889-7:2016ISO 10889-7:2016(E)Bibliography1 ISO 8015, Geometrical product specifications (G
36、PS) Fundamentals Concepts, principles and rules2 ISO 13399 (all parts), Cutting tool data representation and exchange ISO 2016 All rights reserved 5BS ISO 10889-7:2016ISO 10889-7:2016(E) ISO 2016 All rights reservedICS 25.060.20Price based on 5 pagesThis page deliberately left blankBSI is the nation
37、al body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)BSI Group Headqu
38、arters389 Chiswick High Road London W4 4AL UKAbout usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependabl
39、e format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards
40、 by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If
41、 you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further information on our subscription pr
42、oducts go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive su
43、bstantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or re
44、placed. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as th
45、eyre available, you can be sure your documentation is current. For further information, email .RevisionsOur British Standards and other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccura
46、cy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre.CopyrightAll the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that owns copyright
47、 in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transm
48、itted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. Details and advice can be obtained from the Copyright & Licensing Department.Useful Contacts:Customer ServicesTel: +44 845 086 9001Email (orders): Email (enquiries): SubscriptionsTel: +44 845 086 9001Email: Knowledge CentreTel: +44 20 8996 7004Email: Copyright & LicensingTel: +44 20 8996 7070Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW
