1、BS ISO14401-2:2009ICS 53.100NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDEarth-movingmachinery - Field ofvision of surveillanceand rear-view mirrorsPart 2: Performance criteriaThis British Standardwas published underthe authority of theStandards Policy andStr
2、ategy Committee on 30November 2009 BSI 2009ISBN 978 0 580 56176 4Amendments/corrigenda issued since publicationDate CommentsBS ISO 14401-2:2009National forewordThis British Standard is the UK implementation of ISO 14401-2:2009. Itsupersedes BS ISO 14401-2:2004 which is withdrawn.The UK participation
3、 in its preparation was entrusted to TechnicalCommittee B/513/1, Earth moving machinery (International).A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are r
4、esponsible for its correct application.Compliance with a British Standard cannot confer immunityfrom legal obligations.BS ISO 14401-2:2009Reference numberISO 14401-2:2009(E)ISO 2009INTERNATIONAL STANDARD ISO14401-2Second edition2009-08-15Earth-moving machinery Field of vision of surveillance and rea
5、r-view mirrors Part 2: Performance criteria Engins de terrassement Champ de visibilit des rtroviseurs et des miroirs de surveillance Partie 2: Critres de performance BS ISO 14401-2:2009ISO 14401-2:2009(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensin
6、g policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Ce
7、ntral Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been t
8、aken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2009 All rights reserved. Unless otherwise specified, no part of thi
9、s publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-121
10、1 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2009 All rights reservedBS ISO 14401-2:2009ISO 14401-2:2009(E) ISO 2009 All rights reserved iiiForeword ISO (the International Organization for Standardization) is a world
11、wide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on t
12、hat committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in
13、 accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard
14、requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 14401-2 was prepared by T
15、echnical Committee ISO/TC 127, Earth-moving machinery, Subcommittee SC 1, Test methods relating to safety and machine performance. This second edition cancels and replaces the first edition (ISO 14401-2:2004), which has been technically revised. ISO 14401 consists of the following parts, under the g
16、eneral title Earth-moving machinery Field of vision of surveillance and rear-view mirrors: Part 1: Test methods Part 2: Performance criteria BS ISO 14401-2:2009ISO 14401-2:2009(E) iv ISO 2009 All rights reservedIntroduction This part of ISO 14401 gives performance criteria for surveillance and rear-
17、view mirrors fitted to certain earth-moving machinery. The field of vision described is intended to define the minimum visibility area behind the machine in order to provide adequate visibility for the operator when working around other moving machines during operation in a forward/reverse mode or d
18、uring transport on roadways with other traffic. As specified in ISO 5006, mirrors may also be fitted on earth-moving equipment to help meet the visibility performance requirements of ISO 5006 when those requirements cannot be met by direct visibility alone. The testing procedures for mirrors in ISO
19、14401-1 and in ISO 5006 have been aligned to allow a mirror to fulfil the requirements of both ISO 5006 and this part of ISO 14401. Mirrors can also be fitted for the purpose of compliance with national or local regulations, e.g. on-road requirements. BS ISO 14401-2:2009INTERNATIONAL STANDARD ISO 14
20、401-2:2009(E) ISO 2009 All rights reserved 1Earth-moving machinery Field of vision of surveillance and rear-view mirrors Part 2: Performance criteria 1 Scope This part of ISO 14401 specifies criteria for the field-of-vision performance of surveillance and rear-view mirrors on earth-moving machinery.
21、 It is applicable to the ride-on machines of the machine families and sizes listed herein (see Annex A), used both on and off public roads. NOTE 1 For machines not listed in Annex A, the criteria of similar machine types and/or sizes can be used as guidance for the fitting of optional mirrors to the
22、se machines. NOTE 2 Additional national road regulations can apply for machines travelling on public roads. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references,
23、the latest edition of the referenced document (including any amendments) applies. ISO 3411, Earth-moving machinery Physical dimensions of operators and minimum operator space envelope ISO 5006:2006, Earth-moving machinery Operators field of view Test method and performance criteria ISO 6016, Earth-m
24、oving machinery Methods of measuring the masses of whole machines, their equipment and components ISO 6165, Earth-moving machinery Basic types Identification and terms and definitions ISO 14401-1, Earth-moving machinery Field of vision of surveillance and rear-view mirrors Part 1: Test methods 3 Ter
25、ms and definitions For the purposes of this document, the terms and definitions given in ISO 14401-1 apply. BS ISO 14401-2:2009ISO 14401-2:2009(E) 2 ISO 2009 All rights reserved4 Classification of fields of vision The fields of vision are classified as follows. Class A: field of vision as specified
26、in 5.4.2 and shown in Figure 1. Class B: field of vision as specified in 5.4.3 and shown in Figure 2. Class C: field of vision as specified in 5.4.4 and shown in Figure 3. Class D: field of vision as specified in 5.4.5 and shown in Figure 4. 5 Requirements 5.1 General Mirrors and their mounting shal
27、l meet the following requirements. a) Earth-moving machinery according to Annex A shall be equipped as appropriate with a mirror or mirrors conforming to the corresponding field of vision class(es). b) Mirrors shall be installed so as to minimize the effect of vibration during conditions of intended
28、 use as specified by the manufacturer. c) Part or parts of the rear end, left and right of the machine, shall be visible to the operator by means of a mirror or mirrors. Alternatively, closed circuit television cameras (CCTV) may be used to achieve the required fields of vision. 5.2 Mirror positions
29、 The following is applicable. a) If equipped with a cab, exterior rear-view mirrors shall be visible through the portion of the windscreen that is swept by the windscreen wiper or through the side windows. If equipped with a canopy, exterior rear-view mirrors shall be visible through openings in the
30、 canopy. b) A rear-view mirror should not project laterally beyond the outer contour of the machine by more than is necessary to obtain the field of vision specified in 5.4. For machines intended to be used on the road, mirrors that project laterally by more than 0,20 m from the machine (and install
31、ed more than 2 m above ground level) shall be of the foldable type so that they can easily be put back in position if knocked out of alignment. c) Where the bottom edge of an exterior rear-view mirror is less than 2 m above ground level, the mirror shall not project more than 0,3 m beyond the overal
32、l width of the machine. BS ISO 14401-2:2009ISO 14401-2:2009(E) ISO 2009 All rights reserved 3Dimensions in metres Key 1 field of vision 2 rear-view mirror 3 filament position centre-point (FPCP) aMeasurement at ground level. Figure 1 Field of vision Class A BS ISO 14401-2:2009ISO 14401-2:2009(E) 4 I
33、SO 2009 All rights reservedDimensions in metres Key 1 field of vision 2 inner borderline 3 outer borderline 4 filament position centre-point (FPCP) aMeasurement at ground level. bMeasurement at 1,5 m above ground level. Figure 2 Field of vision Class B BS ISO 14401-2:2009ISO 14401-2:2009(E) ISO 2009
34、 All rights reserved 5Dimensions in metres Key 1 field of vision 2 filament position centre-point (FPCP) aMeasurement at ground level. bMeasurement at 1,5 m above ground level. Figure 3 Field of vision Class C BS ISO 14401-2:2009ISO 14401-2:2009(E) 6 ISO 2009 All rights reservedDimensions in millime
35、tres a) Wheeled dumpers b) Crawler dumpers Key r radius (= 100 mm) 1 track 2 rearmost sprocket or idler 3 centreline of rearmost sprocket or idler 4 outermost ground contact point of track Figure 4 Field of vision Class D BS ISO 14401-2:2009ISO 14401-2:2009(E) ISO 2009 All rights reserved 75.3 Adjus
36、tment Mirrors shall be adjustable as follows: a) interior rear-view mirrors shall be adjustable by the operator; b) the adjustment of an exterior mounted mirror shall be accomplished either from the operators station, the ground, from steps or platforms attached to the machine, or from auxiliary pla
37、tforms: the adjusting mechanism shall retain the mirror position during machine operation; folding-type mirror installations shall return to their prior adjustment position when unfolded. 5.4 Fields of vision 5.4.1 General The field of vision shall be determined with the machine test configuration s
38、pecified in ISO 14401-1. For the evaluation of compliance with the performance criteria given in Annex A, measurements need only be made at the measuring locations specified in Figures 1 to 4. NOTE Additional measurements closer to the machine could be required to determine the suitability of the mi
39、rror(s) meeting the requirements for the appropriate field of vision class, for the purpose of meeting the visibility performance requirements of ISO 5006. 5.4.2 Class A The field of vision at ground level shall be such that the operator can see, using the mirror(s), at least a 10 m wide, flat and h
40、orizontal portion of the ground, centred on the vertical longitudinal median plane of the machine, from 30 m behind the rear end of the machine (see Figure 1). 5.4.3 Class B The field of vision shall be such that the operator can see, using the mirror(s), at least a flat portion bounded on the left
41、and right of the machine by a plane parallel to the median longitudinal axis of the machine, passing through the outermost point of the machines overall width. This plane shall start 1 m behind the rear end of the machine at a height of 1,5 m above ground level and at a width of 0,75 m, continuing t
42、o a width of 5 m at ground level 30 m behind the machine (see Figure 2). 5.4.4 Class C The field of vision shall be such that the operator can see, using the mirror(s), at least a flat portion bounded on the left and on the right of the machine by a plane parallel to the median longitudinal vertical
43、 plane passing through the outermost point of the machine on the right and left. This plane shall start 1 m behind the rear end of the machine at a height 1,5 m above ground level and at a width of 1 m, continuing to a width of 7,5 m at ground level 30 m behind the machine (see Figure 3). 5.4.5 Clas
44、s D Dumpers For wheeled dumpers, the field of vision at ground level shall be such that the operator can see, using the mirror(s), at least the outer ground contact point (within a radius of 100 mm) of the rear tyres on the left and right of the machine see Figure 4 a). For crawler dumpers, the fiel
45、d of vision at ground level shall be such that the operator can see, using the mirror(s), at least the ground projection (within a radius of 100 mm) of the outermost points of the tracks at the centre lines of the rearmost sprockets or idlers on the left and right of the machine see Figure 4 b). BS
46、ISO 14401-2:2009ISO 14401-2:2009(E) 8 ISO 2009 All rights reserved5.4.6 Number of mirrors A combination of interior and exterior mirrors may be used to provide the fields of vision specified in 5.4.2 to 5.4.5. 6 Visibility information in operators instructions The machine operators instructions shal
47、l contain the following, so that the operator can minimize visibility hazards when operating the machine: information regarding the positioning and use of mirrors; information to the effect that modifications of the machine configuration by the user of the machine that will result in a restriction o
48、f machine visibility must be verified according to this part of ISO 14401. BS ISO 14401-2:2009ISO 14401-2:2009(E) ISO 2009 All rights reserved 9Annex A (normative) Surveillance and rear-view mirrors Field of vision Mirrors for field of vision class A are not applicable to machines without cab, ROPS
49、or canopy, but shall be covered by the mirrors used, for example, for class B or C. Applicability shall be in accordance with Table A.1. Table A.1 Minimum mirror field-of-vision requirements for different machine families Machine family according to ISO 6165 Operating mass according to ISO 6016 Field of vision class(es) (see Clause 4) Crawler dozers 4 500 kg u 30 000 kg Aa, B Compact loadersbAcor BaBackhoe loaders 15 000 kg B Wheeled excavators 25 000
