1、BS ISO15375:2010ICS 11.040.20NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDMedical infusionbottles Suspensiondevices for multipleuse Requirementsand test methodsThis British Standardwas published under theauthority of the StandardsPolicy and StrategyCommittee
2、on 30 June2010 BSI 2010ISBN 978 0 580 66148 8Amendments/corrigenda issued since publicationDate CommentsBS ISO 15375:2010National forewordThis British Standard is the UK implementation of ISO 15375:2010. Itsupersedes BS ISO 15375:2004 which is withdrawn.The UK participation in its preparation was en
3、trusted to TechnicalCommittee CH/212, IVDs.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct application.Compliance with a Brit
4、ish Standard cannot confer immunityfrom legal obligations.BS ISO 15375:2010Reference numberISO 15375:2010(E)ISO 2010INTERNATIONAL STANDARD ISO15375Second edition2010-06-15Medical infusion bottles Suspension devices for multiple use Requirements and test methods Flacons mdicaux de transfusion et de p
5、erfusion Dispositifs de suspension usage multiple Exigences et mthodes dessai BS ISO 15375:2010ISO 15375:2010(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces wh
6、ich are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems I
7、ncorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
8、 that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2010 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mecha
9、nical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso
10、.org Published in Switzerland ii ISO 2010 All rights reservedBS ISO 15375:2010ISO 15375:2010(E) ISO 2010 All rights reserved iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing Internat
11、ional Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with I
12、SO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical c
13、ommittees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to th
14、e possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 15375 was prepared by Technical Committee ISO/TC 76, Transfusion, infusion and injection equipment for medical and pharma
15、ceutical use. This second edition cancels and replaces the first edition (ISO 15375:2004), Clause 2 of which has been technically revised. BS ISO 15375:2010ISO 15375:2010(E) iv ISO 2010 All rights reservedIntroduction This International Standard deals with permanent suspension devices for multiple u
16、se for infusion bottles in accordance with ISO 8536-1. The intended purpose of suspension devices is to avoid dropdowns of infusion bottles during administering of blood or pharmaceutical solutions. BS ISO 15375:2010INTERNATIONAL STANDARD ISO 15375:2010(E) ISO 2010 All rights reserved 1Medical infus
17、ion bottles Suspension devices for multiple use Requirements and test methods 1 Scope This International Standard specifies requirements for permanent suspension devices, fixed to infusion racks or set-up devices, for infusion bottles that confirm to the requirements of ISO 8536-1. The suspension de
18、vices are intended for multiple use. The purpose of this International Standard is to establish a safe suspension device for infusion bottles during administering of their contents. 2 Normative references The following referenced documents are indispensable for the application of this document. For
19、dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 2768-1, General tolerances Part 1: Tolerances for linear and angular dimensions without individual tolerance indications ISO 8536-1, Infusio
20、n equipment for medical use Part 1: Infusion glass bottles 3 Designation code and test weights Permanent suspension devices that comply with the requirements of this International Standard are designated by the description block, followed by a reference to this International Standard, followed by th
21、e nominal volume as specified in Table 1. For example, a permanent suspension device for an infusion bottle that conforms to the requirements of ISO 8536-1 of nominal capacity of 50 ml to 250 ml is designated as follows: Suspension device ISO 15375 - M 50 - 250 Test weights used for the permanent lo
22、ad test (see 6.4) are also a function of the nominal capacity of the permanent suspension device and are specified in Table 1. Table 1 Designation code and test weights for permanent load test Nominal capacity of the bottles ml Test weight at 24 h kg u 250 3 250 5 BS ISO 15375:2010ISO 15375:2010(E)
23、2 ISO 2010 All rights reserved4 Material Materials selected for the permanent suspension device shall ensure that all requirements given in Clause 5 can be met. Certain materials can be chemically and physically damaged by disinfectants. Therefore, attention should be given to selecting materials th
24、at are more inert towards disinfectants and less sensitive to stress cracking and thermal stress. 5 Requirements 5.1 Design 5.1.1 When tested in accordance with 6.1, the multiple suspension device shall enable the installation of the bottle with a perforated transfer set. The suspension device shall
25、 be designed in such a way that an unintentional removal from an infusion rack or set-up device is not possible. 5.1.2 The design of the suspension device shall guarantee that the bottle is in a perpendicular position with a maximum deviation of 15. 5.1.3 When tested in accordance with 6.2, the desi
26、gn of the suspension device shall guarantee that the bottle does not fall off at angles of up to 45. 5.1.4 The suspension device shall be resistant to corrosion and practically free from burrs. 5.2 Sterilization and disinfection The manufacturers manual shall contain information indicating how the s
27、uspension device shall be cleaned, sterilized and disinfected. 5.3 Load 5.3.1 Gravitational load When tested in accordance with 6.3, the permanent suspension device shall not detach from the infusion bottle. It shall not be damaged by the test. 5.3.2 Permanent load When tested in accordance with 6.4
28、, the multiple suspension device shall prevent the infusion bottle from falling. It shall not be damaged by the test. 5.4 Life cycle 5.4.1 If the design of the permanent suspension device or materials used in its construction have a limited life cycle u 5 y, the manufacturer shall define the storage
29、 conditions and the time period during which a permanent suspension device is considered to be in conformance with this International Standard. 5.4.2 In order to take different user conditions into consideration, the manufacturer shall define assessment criteria to enable the user to establish when
30、the suspension device is no longer usable. BS ISO 15375:2010ISO 15375:2010(E) ISO 2010 All rights reserved 36 Testing 6.1 Assembly test The bottle with the connected transfer set is attached to the suspension device, e.g. hung on a hook having characteristics in accordance with those shown in Figure
31、 1. Any deviation of the orientation of the bottle from the perpendicular is recorded. The assembly test shall be repeated with all bottle sizes that will be used with the suspension device. 6.2 Sloping test The suspension device assembled with the bottle and the perforated transfer set is tilted to
32、 an angle of 45. The bottle shall not drop off of the suspension device. The sloping test shall be repeated with all bottle sizes that will be used with the suspension device. General tolerances are in accordance with class “m” (medium) as defined in ISO 2768-1. Dimensions in millimetres Figure 1 Te
33、st hook 6.3 Gravitational test Attach the permanent suspension device, fitted with a filled infusion bottle complying with ISO 8536-1, to the test hook (see Figure 1). Attach one end of a cord to the upper part of the hook, and the other end to a separate fixed point. Hold the suspension device and
34、hook level with the fixed point and drop the assemblage such that the cord stops the fall of the suspension device when it is at a vertical distance of 30 cm from the fixed point. The suspension device is considered to pass the test if the requirements specified in 5.3.1 are met. 6.4 Permanent load
35、test Using a hook with a diameter of 4 mm, e.g. in accordance with Figure 1, load the multiple suspension device for 24 h at (23 2) C and (50 3) % relative humidity with a test weight in accordance with Table 1. The suspension device is considered to pass the test if the requirements specified in 5.
36、3.2 are met. BS ISO 15375:2010ISO 15375:2010(E) ICS 11.040.20 Price based on 3 pages ISO 2010 All rights reserved BS ISO 15375:2010This page has been intentionally left blank BS ISO15375:2010BSI GroupHeadquarters 389Chiswick High Road,London, W4 4AL, UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 - Br
37、itish Standards InstitutionBSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at theinternational level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of Brit
38、ishStandards should make sure that they possess the latest amendments oreditions.It is the constant aim of BSI to improve the quality of our products and services.We would be grateful if anyone finding an inaccuracy or ambiguity while usingthis British Standard would inform the Secretary of the tech
39、nical committeeresponsible, the identity of which can be found on the inside front cover. Tel:+44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Buying standa
40、rdsOrders for all BSI, international and foreign standards publications should beaddressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 89967001 Email: You may also buy directly using a debit/creditcard from the BSI Shop on the Website http:/ response to orders for international s
41、tandards, it is BSI policy to supply theBSI implementation of those that have been published as British Standards,unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European andinternational standards through its Library and its Technical Help to
42、 ExportersService. Various BSI electronic information services are also available whichgive details on all its products and services. Contact Information Centre. Tel:+44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: Subscribing members of BSI are kept up to date with standards developmentsand rece
43、ive substantial discounts on the purchase price of standards. For detailsof these and other benefits contact Membership Administration. Tel: +44 (0)208996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via British StandardsOnline can be found at http:/
44、information about BSI is available on the BSI website at http:/CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in theUK, of the publications of the international standardization bodies. Except aspermitted under the Copyright, Designs and Patents Act 1988 no extract
45、 maybe reproduced, stored in a retrieval system or transmitted in any form or by anymeans electronic, photocopying, recording or otherwise without prior writtenpermission from BSI.This does not preclude the free use, in the course of implementing the standard,of necessary details such as symbols, and size, type or grade designations. Ifthese details are to be used for any other purpose than implementation then theprior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright and Licensing Manager.Tel: +44 (0)20 8996 7070 Email:
