1、Radiofrequency identification of animalsPart 4: Evaluation of performance of RFID transceivers conforming with ISO 11784 and ISO 11785BS ISO 246314:2017BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06 ISO 2017Radiofrequency identification of animals Part 4: Evaluatio
2、n of performance of RFID transceivers conforming with ISO 11784 and ISO 11785Identification des animaux par radiofrquence Partie 4: valuation de la performance des metteurs-rcepteurs RFID conformes lISO 11784 et lISO 11785INTERNATIONAL STANDARDISO24631-4Second edition2017-09Reference numberISO 24631
3、-4:2017(E)National forewordThis British Standard is the UK implementation of ISO 246314:2017. It supersedes BS ISO 246314:2009, which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee AGE/6/1, Radio Frequency ID for Animals.A list of organizations represented
4、on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2017 Published by BSI Standards Limited 2017ISBN 978 0 580 81934
5、 6ICS 65.040.99Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 September 2017.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARD
6、BS ISO 246314:2017 ISO 2017Radiofrequency identification of animals Part 4: Evaluation of performance of RFID transceivers conforming with ISO 11784 and ISO 11785Identification des animaux par radiofrquence Partie 4: valuation de la performance des metteurs-rcepteurs RFID conformes lISO 11784 et lIS
7、O 11785INTERNATIONAL STANDARDISO24631-4Second edition2017-09Reference numberISO 24631-4:2017(E)BS ISO 246314:2017ISO 24631-4:2017(E)ii ISO 2017 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2017, Published in SwitzerlandAll rights reserved. Unless otherwise specified, no part of this publicati
8、on may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country o
9、f the requester.ISO copyright officeCh. de Blandonnet 8 CP 401CH-1214 Vernier, Geneva, SwitzerlandTel. +41 22 749 01 11Fax +41 22 749 09 47copyrightiso.orgwww.iso.orgBS ISO 246314:2017ISO 24631-4:2017(E)ii ISO 2017 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2017, Published in SwitzerlandAll
10、 rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested fr
11、om either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCh. de Blandonnet 8 CP 401CH-1214 Vernier, Geneva, SwitzerlandTel. +41 22 749 01 11Fax +41 22 749 09 47copyrightiso.orgwww.iso.orgISO 24631-4:2017(E)Foreword ivIntroduction v1 Scope . 12 Normat
12、ive references 13 Terms and definitions . 14 Conformance . 35 Abbreviated terms 36 Application . 47 Test procedures . 57.1 Test apparatus . 57.2 Test conditions 57.3 Measurement of reading distance diagram 57.3.1 Purpose 57.3.2 Transponder orientation 57.3.3 Test geometry . 67.3.4 Procedure . 77.4 M
13、easurement of transceiver response time 77.4.1 Purpose 77.4.2 Test geometry . 87.4.3 Procedure . 8Annex A (normative) Test application form (ISO 24631-4) . 9Annex B (normative) Transponder emulation circuit (TEC) design specifications (ISO 246314) .10Annex C (informative) Example of distance diagram
14、 (ISO 24631-4) .14Bibliography .15 ISO 2017 All rights reserved iiiContents PageBS ISO 246314:2017ISO 24631-4:2017(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standa
15、rds is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also tak
16、e part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In par
17、ticular, the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of
18、 this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see
19、www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and expressions related to conformity assessment, as well as i
20、nformation about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see the following URL: www.iso.org/iso/foreword.html.This document was prepared by Technical Committee ISO/TC 23, Tractors and machinery for agriculture and forestry, Subcommitt
21、ee SC 19, Agricultural electronics.This second edition cancels and replaces the first edition (ISO 24631-4:2009), which has been technically revised.The main change to the previous edition is as follows: Figure C.1 has been updated.A list of all parts in the ISO series can be found on the ISO websit
22、e.iv ISO 2017 All rights reservedBS ISO 246314:2017ISO 24631-4:2017(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technic
23、al committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely wi
24、th the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed
25、 for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rig
26、hts. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in thi
27、s document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the World Tr
28、ade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see the following URL: www.iso.org/iso/foreword.html.This document was prepared by Technical Committee ISO/TC 23, Tractors and machinery for agriculture and forestry, Subcommittee SC 19, Agricultural electronics.This second
29、edition cancels and replaces the first edition (ISO 24631-4:2009), which has been technically revised.The main change to the previous edition is as follows: Figure C.1 has been updated.A list of all parts in the ISO series can be found on the ISO website.iv ISO 2017 All rights reserved ISO 24631-4:2
30、017(E)IntroductionISO has appointed a registration authority (RA) competent to register manufacturer codes used in the radiofrequency identification (RFID) of animals in accordance with ISO 11784 and ISO 11785.The registration authority for ISO 11784 and ISO 11785 can found under:http:/www.iso.org/i
31、so/ home/standards_development/list_of_iso_technical_committees/maintenance_agencies.htmThis document deals with the performance of RFID transceivers. Measurements are made using transponder emulation circuits, ensuring that the transceiver testing is always performed against the same, known stimuli
32、. ISO 2017 All rights reserved vBS ISO 246314:2017BS ISO 246314:2017Radiofrequency identification of animals Part 4: Evaluation of performance of RFID transceivers conforming with ISO 11784 and ISO 117851 ScopeThis document provides the means of evaluating the performance of ISO 11784- and ISO 11785
33、-conformant RFID (radiofrequency identification) transceivers used in the individual identification of animals.The test procedures specified in this document are recognized by the Federation of European Companion Animals Veterinary Association (FECAVA) and World Small Animal Veterinarian Association
34、 (WSAVA) and, as such, can be applied also to companion animals.2 Normative referencesThe following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated refer
35、ences, the latest edition of the referenced document (including any amendments) applies.ISO 3166-1, Codes for the representation of names of countries and their subdivisions Part 1: Country codesISO 11784, Radio frequency identification of animals Code structureISO 11785:1996, Radio frequency identi
36、fication of animals Technical conceptISO 24631-2, Radiofrequency identification of animals Part 2: Evaluation of conformance of RFID transceivers with ISO 11784 and ISO 11785ISO 24631-5, Radio frequency identification of animals Part 5: Procedure for testing the capability of RFID transceivers of re
37、ading ISO 11784 and ISO 11785 transponders3 Terms and definitionsFor the purposes of this document, the following terms and definitions apply.ISO and IEC maintain terminological databases for use in standardization at the following addresses: IEC Electropedia: available at http:/www.electropedia.org
38、/ ISO Online browsing platform: available at http:/www.iso.org/obp3.1accreditationthird-party attestation related to a conformity assessment body conveying formal demonstration of its competence to carry out specific conformity assessment tasksSOURCE: ISO/IEC 17000INTERNATIONAL STANDARD ISO 24631-4:
39、2017(E) ISO 2017 All rights reserved 1BS ISO 246314:2017ISO 24631-4:2017(E)3.2registration reference numbernumber issued to the manufacturer of a registered transceiver by the registration authorityEXAMPLE ISO 24631-2 2017-02-001Note 1 to entry: It comprises the reference of the International Standa
40、rd for which registration is made, the year of issue (4 digits), the type of device tested (“02” for transceivers according to this document) and the running number (3 digits) referencing the transceivers tested successfully during that year.3.3country codethree-digit numeric code representing a cou
41、ntry in accordance with ISO 3166-13.4ISO 11784 and ISO 11785 transceivertransceiver that reads at least both FDX-B and HDX transponders as defined in ISO 11784 and ISO 117853.5ISO 11784 and ISO 11785 transponderradiofrequency identification (RFID) device that transmits its transponder code according
42、 to ISO 11784 and ISO 11785 when activated by a transceiver3.6manufacturercompany that submits an application for testing transceivers for conformance with ISO 11784 and ISO 117853.7manufacturer codeMFCthree-digit number granted by the RA to a manufacturer under the conditions set forth in ISO 24631
43、-1:2017, Annex E, whose range and placement within the code structure are in accordance with ISO 11784Note 1 to entry: Only one manufacturer code is granted to the same manufacturer.3.8RA-recognized test centreaccredited test centre meeting the criteria of the registration authority3.9RA-registered
44、transpondertransponder registered by the registration authority3.10reference transpondertransponder used to test a transceiver, selected from the different RA-registered transponder types3.11registration authorityRAentity that approves test laboratories and issues and registers manufacturer and prod
45、uct codes3.12transceiverdevice used to communicate with the transponder2 ISO 2017 All rights reservedBS ISO 246314:2017ISO 24631-4:2017(E)3.2registration reference numbernumber issued to the manufacturer of a registered transceiver by the registration authorityEXAMPLE ISO 24631-2 2017-02-001Note 1 t
46、o entry: It comprises the reference of the International Standard for which registration is made, the year of issue (4 digits), the type of device tested (“02” for transceivers according to this document) and the running number (3 digits) referencing the transceivers tested successfully during that
47、year.3.3country codethree-digit numeric code representing a country in accordance with ISO 3166-13.4ISO 11784 and ISO 11785 transceivertransceiver that reads at least both FDX-B and HDX transponders as defined in ISO 11784 and ISO 117853.5ISO 11784 and ISO 11785 transponderradiofrequency identificat
48、ion (RFID) device that transmits its transponder code according to ISO 11784 and ISO 11785 when activated by a transceiver3.6manufacturercompany that submits an application for testing transceivers for conformance with ISO 11784 and ISO 117853.7manufacturer codeMFCthree-digit number granted by the R
49、A to a manufacturer under the conditions set forth in ISO 24631-1:2017, Annex E, whose range and placement within the code structure are in accordance with ISO 11784Note 1 to entry: Only one manufacturer code is granted to the same manufacturer.3.8RA-recognized test centreaccredited test centre meeting the criteria of the registration authority3.9RA-registered transpondertransponder registered by the registration authority3.10reference transpondertransponder used to test a transceiver, select
