1、BS ISO 366-3:2009ICS 59.120.30NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDTextile machinery andaccessories ReedsPart 3: Dimensions and designation ofmetal reeds with double-spring baulkThis British Standardwas published underthe authority of theStandards Pol
2、icy andStrategy Committee on 30September 2009 BSI 2009ISBN 978 0 580 57693 5Amendments/corrigenda issued since publicationDate CommentsBS ISO 366-3:2009National forewordThis British Standard is the UK implementation of ISO 366-3:2009.The UK participation in its preparation was entrusted to Technical
3、Committee TCI/33, Textile machinery.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct application.Compliance with a British Sta
4、ndard cannot confer immunityfrom legal obligations.BS ISO 366-3:2009Reference numberISO 366-3:2009(E)ISO 2009INTERNATIONAL STANDARD ISO366-3Second edition2009-03-01Textile machinery and accessories Reeds Part 3: Dimensions and designation of metal reeds with double-spring baulk Matriel pour lindustr
5、ie textile Peignes Partie 3: Dimensions et dsignation des peignes mtalliques ligature double BS ISO 366-3:2009ISO 366-3:2009(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless t
6、he typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of
7、Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the
8、 unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2009 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, elec
9、tronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.
10、org Web www.iso.org Published in Switzerland ii ISO 2009 All rights reservedBS ISO 366-3:2009ISO 366-3:2009(E) ISO 2009 All rights reserved iiiContents Page Foreword iv 1 Scope . 1 2 Dimensions 1 3 Designation . 1 BS ISO 366-3:2009ISO 366-3:2009(E) iv ISO 2009 All rights reservedForeword ISO (the In
11、ternational Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee h
12、as been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical
13、 standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodi
14、es for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any
15、or all such patent rights. ISO 366-3 was prepared by Technical Committee ISO/TC 72, Textile machinery and accessories, Subcommittee SC 3, Machinery for fabric manufacturing including preparatory machinery and accessories. This second edition cancels and replaces the first edition (ISO 366-3:1988), w
16、hich has been technically revised. ISO 366 consists of the following parts, under the general title Textile machinery and accessories Reeds: Part 1: Pitch bound reeds Dimensions Part 2: Dimensions and designation of metal reeds with plate baulk Part 3: Dimensions and designation of metal reeds with
17、double-spring baulk Part 4: Dimensions and designation of plastic-bound metal reeds Part 5: Dimensions and designation of profile capsules BS ISO 366-3:2009INTERNATIONAL STANDARD ISO 366-3:2009(E) ISO 2009 All rights reserved 1Textile machinery and accessories Reeds Part 3: Dimensions and designatio
18、n of metal reeds with double-spring baulk 1 Scope This part of ISO 366 specifies the dimensions and designation of metal reeds with double-spring baulk for weaving machines. 2 Dimensions The dimensions of metal reeds with double-spring baulk shown in Figure 1 and given in Table 1, and the tolerance
19、of perpendicularity of dents according Figure 2, shall be met. 3 Designation The designation of metal reeds with double-spring baulk shall include the following information in the order given: a) “Metal reed with double-spring baulk”; b) reference to this part of ISO 366, i.e. ISO 366-3; c) inner he
20、ight of the reed, e, in millimetres; d) overall height of the reed, h1, in millimetres; e) thickness of the reed baulk, d, in millimetres; f) width of the dents of the reed, b, in millimetres; g) type of steel used for the dents of the reed, i.e. plain or stainless. EXAMPLE A metal reed with double-
21、spring baulk of total height h1= 150 mm, of thickness of reed baulk d = 8 mm, and having dents of width b = 4 mm, made of stainless steel, is designated as follows: Metal reed with double-spring baulk ISO 366-3 - 150 8 4 stainless steel BS ISO 366-3:2009ISO 366-3:2009(E) 2 ISO 2009 All rights reserv
22、edKey B overall width of reed BNusable width b width of dents of reed d thickness of reed baulk (approximate value, depends on the thickness or diameter of the wire) e inner height of reed h1total height of reed f width of end piece Figure 1 Metal reed with double-spring baulk Table 1 Dimensions of
23、metal reeds with double-spring baulk Dimensions in millimetres Width of dents of reed b 3 4 (5) 6 Thickness of reed baulk d Total height of reed h16,5 8 (9) 10 110 120 130 140 150 160 NOTE The grey table elements show the dimensions recommended for metal reed with plate baulk. BS ISO 366-3:2009ISO 3
24、66-3:2009(E) ISO 2009 All rights reserved 3Key e inner height of reed h1total height of reed s thickness of dents t distance of dents Figure 2 Tolerance of perpendicularity of dents in relation to base of reed BS ISO 366-3:2009ISO 366-3:2009(E) ICS 59.120.30 Price based on 3 pages ISO 2009 All right
25、s reserved BS ISO 366-3:2009This page has been intentionally left blank BS ISO366-3:2009BSI GroupHeadquarters 389Chiswick High Road,London, W4 4AL, UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 - British Standards InstitutionBSI is the independent national body responsible for preparing BritishStanda
26、rds. It presents the UK view on standards in Europe and at theinternational level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments oreditions.It is the constant aim
27、 of BSI to improve the quality of our products and services.We would be grateful if anyone finding an inaccuracy or ambiguity while usingthis British Standard would inform the Secretary of the technical committeeresponsible, the identity of which can be found on the inside front cover. Tel:+44 (0)20
28、 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should beaddressed to Customer
29、Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 89967001 Email: You may also buy directly using a debit/creditcard from the BSI Shop on the Website http:/ response to orders for international standards, it is BSI policy to supply theBSI implementation of those that have been published as British
30、 Standards,unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European andinternational standards through its Library and its Technical Help to ExportersService. Various BSI electronic information services are also available whichgive details on
31、all its products and services. Contact Information Centre. Tel:+44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: Subscribing members of BSI are kept up to date with standards developmentsand receive substantial discounts on the purchase price of standards. For detailsof these and other benefits co
32、ntact Membership Administration. Tel: +44 (0)208996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via British StandardsOnline can be found at http:/ information about BSI is available on the BSI website at http:/CopyrightCopyright subsists in all BSI p
33、ublications. BSI also holds the copyright, in theUK, of the publications of the international standardization bodies. Except aspermitted under the Copyright, Designs and Patents Act 1988 no extract maybe reproduced, stored in a retrieval system or transmitted in any form or by anymeans electronic, p
34、hotocopying, recording or otherwise without prior writtenpermission from BSI.This does not preclude the free use, in the course of implementing the standard,of necessary details such as symbols, and size, type or grade designations. Ifthese details are to be used for any other purpose than implementation then theprior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright and Licensing Manager.Tel: +44 (0)20 8996 7070 Email:
