1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationPD CEN/TS 13388:2013Copper and copper alloys Compendium of compositionsand productsCopyright European Committee for Standardization Provided by IHS under license with CENNot for
2、ResaleNo reproduction or networking permitted without license from IHS-,-,-PD CEN/TS 13388:2013 PUBLISHED DOCUMENTNational forewordThis Published Document is the UK implementation of CEN/TS 13388:2013. It supersedes DD CEN/TS 13388:2008 which is withdrawn.The UK participation in its preparation was
3、entrusted to Technical Committee NFE/34, Copper and copper alloys.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct applicati
4、on. The British Standards Institution 2013. Published by BSI Standards Limited 2013ISBN 978 0 580 79610 4 ICS 77.120.30; 77.150.30 Compliance with a British Standard cannot confer immunity from legal obligations.This Published Document was published under the authority of the Standards Policy and St
5、rategy Committee on 31 March 2013.Amendments issued since publicationDate T e x t a f f e c t e dCopyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-PD CEN/TS 13388:2013TECHNICAL SPE
6、CIFICATION SPCIFICATION TECHNIQUE TECHNISCHE SPEZIFIKATION CEN/TS 13388 February 2013 ICS 77.120.30; 77.150.30 Supersedes CEN/TS 13388:2008English Version Copper and copper alloys - Compendium of compositions and products Cuivre et alliages de cuivre - Inventaire des compositions et des produits Kup
7、fer und Kupferlegierungen - bersicht ber Zusammensetzungen und Produkte This Technical Specification (CEN/TS) was approved by CEN on 17 December 2012 for provisional application. The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be req
8、uested to submit their comments, particularly on the question whether the CEN/TS can be converted into a European Standard. CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS available promptly at national level in an appropriate for
9、m. It is permissible to keep conflicting national standards in force (in parallel to the CEN/TS) until the final decision about the possible conversion of the CEN/TS into an EN is reached. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, D
10、enmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMIT
11、TEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. CEN/TS 13388:2013: ECopyright European Com
12、mittee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-PD CEN/TS 13388:2013CEN/TS 13388:2013 (E) 2 Contents Page Foreword 4 Introduction .5 1 Scope 6 2 Normative references 6 3 Compositions of coppers and co
13、pper alloys standardised by CEN/TC 133 .6 3.1 Composition of coppers .6 3.2 Composition of copper alloys 6 3.3 Composition of master alloys 7 3.4 Composition of ingots and castings7 3.5 Composition of filler metals .7 3.6 Composition of copper and copper alloy scrap .7 4 Available product forms of c
14、opper and copper alloys standardised by CEN/TC 133 7 4.1 Wrought coppers and copper alloys .7 4.2 Master alloys 7 4.3 Ingots and castings .8 4.4 Filler metals 8 4.5 Scrap .8 5 Copper and copper alloys standardised by other CEN Technical Committees 8 6 Copper and copper alloys registered by CEN/TC 13
15、3 .8 Table 1.1 Composition of copper cathodes according to EN 1978:1998, Cu-CATH-1 (CR001A) and Cu-CATH-2 (CR002A) .9 Table 1.2 Composition of unalloyed copper grades made from Cu-CATH-1 (CR001A) according to EN 1978 . 10 Table 1.3 Composition of unalloyed copper grades, other than those made from C
16、u-CATH-1 (CR001A) according to EN 1978 . 11 Table 1.4 Composition of phosphorus-containing copper grades 11 Table 1.5 Composition of silver-containing copper grades (silver-bearing coppers) . 12 Table 2 Composition of copper alloys, low alloyed (less than 5 % alloying elements) . 13 Table 3 Composit
17、ion of copper-aluminium alloys . 15 Table 4 Composition of copper-nickel alloys . 15 Table 5 Composition of copper-nickel-zinc alloys 16 Table 6 Composition of copper-tin alloys 17 Table 7 Composition of copper-zinc alloys, binary . 18 Table 8 Composition of copper-zinc-lead alloys . 19 Table 9 Comp
18、osition of copper-zinc alloys, complex . 21 Table 10 Wrought coppers and copper alloys specified in European product Standards prepared by CEN/TC 133 . 23 Table 11 Master alloys Composition 35 Table 12.1 Ingots and castings Copper and copper-chromium alloys Compositions and casting processes . 38 Ta
19、ble 12.2 Ingots and castings Copper-zinc alloys Composition and casting processes 39 Table 12.3 Ingots and castings Copper-tin alloys Composition and casting processes . 42 Table 12.4 Ingots and castings Copper-tin-lead alloys Composition and casting processes 43 Table 12.5 Ingots and castings Coppe
20、r-aluminium alloys Composition and casting processes45 Table 12.6 Ingots and castings Copper-manganese-aluminium alloys Composition and casting processes . 46 Table 12.7 Ingots and castings Copper-nickel alloys Composition and casting processes . 47 Table 13.1 Filler metals Composition of copper 48
21、Table 13.2 Filler metals Composition of miscellaneous copper alloys 49 Table 13.3 Filler metals Composition of copper-zinc alloys 50 Table 13.4 Filler metals Composition of copper-tin alloys . 51 Table 13.5 Filler metals Composition of copper-aluminium alloys . 51 Table 13.6 Filler metals Compositio
22、n of copper-nickel-zinc alloys . 52 Table 14 Scrap Composition . 52 Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-PD CEN/TS 13388:2013CEN/TS 13388:2013 (E) 3 Table 15.1 Class A
23、G: silver brazing filler metals standardised by CEN/TC 121 56 Table 15.2 Class CP: copper-phosphorus brazing filler metals standardised by CEN/TC 121 . 57 Table 15.3 Class CU: copper brazing filler metals Series CU 100 and CU 200 standardised by CEN/TC 121 . 58 Table 15.4 Class CU: copper brazing fi
24、ller metals Series Cu 300 standardised by CEN/TC 121 58 Table 16 Composition of copper alloys, standardised by CLC/TC 9X . 59 Bibliography 60 Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license f
25、rom IHS-,-,-PD CEN/TS 13388:2013CEN/TS 13388:2013 (E) 4 Foreword This document (CEN/TS 13388:2013) has been prepared by Technical Committee CEN/TC 133 “Copper and copper alloys”, the secretariat of which is held by DIN. Attention is drawn to the possibility that some of the elements of this document
26、 may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes CEN/TS 13388:2008. According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following countries are bou
27、nd to announce this Technical Specification: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Po
28、rtugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. This revision takes into account the latest changes regarding materials and compositions to: EN 1172:2011; EN 1976:2012; EN 12449:2012; EN 12163:2011; EN 12164:2011; EN 12165:2011; EN 12166:2011; EN 12167
29、:2011; EN 12168:2011. Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-PD CEN/TS 13388:2013CEN/TS 13388:2013 (E) 5 Introduction CEN/TC 133 “Copper and copper alloys“ was establish
30、ed in 1988 to prepare and maintain standards in the field of unwrought, wrought and cast products made from copper and copper alloys. Its responsibilities included developing, defining, specifying and giving guidance on, as appropriate, material compositions, designations, terminology, dimensions an
31、d tolerances, mechanical and physical characteristics, conditions of delivery and methods of testing peculiar to copper and copper alloys. During the development of standards for copper and copper alloy products, the experts realised the necessity and seised the opportunity: a) to co-ordinate and in
32、 some cases also to rationalise the composition limits which already existed for the various product forms; b) to establish unique, new and identifiably European designations for copper and copper alloys, including a numerical option to be particularly convenient for computerised handling; c) to con
33、firm, clarify and re-define where necessary, the terminology which already existed in common usage, at the international level or in customs nomenclature. CEN/TC 133 decided, in view of the new form of presentation and new parameters for the description and provision of information on copper and cop
34、per alloy products, to prepare and publish the present consolidation and summary of essential details. Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-PD CEN/TS 13388:2013CEN/TS
35、13388:2013 (E) 6 1 Scope This Technical Specification provides a summary of material designations, compositions and the product forms in which they are available, for coppers and copper alloys standardised in European Standards by CEN/TC 133 “Copper and copper alloys“. It also includes copper alloys
36、 which are not standardised by CEN/TC 133 but by other CEN Technical Committees responsible for products in copper alloys, and other copper alloys not yet standardised. These alloys have been registered by CEN/TC 133 in accordance with the procedures laid down in CR 12776. 2 Normative references The
37、 following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 1976, C
38、opper and copper alloys Cast unwrought copper products EN 1982:2008, Copper and copper alloys Ingots and castings 3 Compositions of coppers and copper alloys standardised by CEN/TC 133 3.1 Composition of coppers The symbol and number designations and compositions of copper grades are given in the fo
39、llowing tables: Table 1.1 Composition of copper cathodes according to EN 1978:1998, Cu-CATH-1 (CR001A) and Cu-CATH-2 (CR002A) Table 1.2 Composition of unalloyed copper grades made from Cu-CATH-1 (CR001A) Table 1.3 Composition of unalloyed copper grades, other than those made from Cu-CATH-1 (CR001A)
40、Table 1.4 Composition of phosphorus-containing copper grades Table 1.5 Composition of silver-containing copper grades (silver-bearing coppers) 3.2 Composition of copper alloys The symbol and number designations and compositions of copper alloys are given in the following tables: Table 2 Composition
41、of copper alloys, low alloyed (less than 5 % alloying elements) Table 3 Composition of copper-aluminium alloys Table 4 Composition of copper-nickel alloys Table 5 Composition of copper-nickel-zinc alloys Table 6 Composition of copper-tin alloys Table 7 Composition of copper-zinc alloys, binary Table
42、 8 Composition of copper-zinc-lead alloys Table 9 Composition of copper-zinc alloys, complex Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-PD CEN/TS 13388:2013 CEN/TS 13388:201
43、3 (E) 7 3.3 Composition of master alloys The symbol and number designations and compositions of master alloys in accordance with EN 1981:2003 are given in Table 11. 3.4 Composition of ingots and castings The symbol and number designations and compositions of ingots and castings in accordance with EN
44、 1982:2008 are given in the following tables: Table 12.1 Ingots and castings Composition of copper and copper-chromium alloys and casting processes Table 12.2 Ingots and castings Composition of copper-zinc alloys and casting processes Table 12.3 Ingots and castings Composition of copper-tin alloys a
45、nd casting processes Table 12.4 Ingots and castings Composition of copper-tin-lead alloys and casting processes Table 12.5 Ingots and castings Composition of copper-aluminium alloys and casting processes Table 12.6 Ingots and castings Composition of copper-manganese-aluminium alloys and casting proc
46、esses Table 12.7 Ingots and castings Composition of copper-nickel alloys and casting processes 3.5 Composition of filler metals The symbol and number designations and compositions of filler metals in accordance with EN 13347:2002 are given in the following tables: Table 13.1 Filler metals Compositio
47、n of copper Table 13.2 Filler metals Composition of miscellaneous copper alloys Table 13.3 Filler metals Composition of copper-zinc alloys Table 13.4 Filler metals Composition of copper-tin alloys Table 13.5 Filler metals Composition of copper-aluminium alloys Table 13.6 Filler metals Composition of
48、 copper-nickel-zinc alloys 3.6 Composition of copper and copper alloy scrap The symbol and number designations and compositions of copper and copper alloy scrap in accordance with EN 12861:1999 are given in Table 14. 4 Available product forms of copper and copper alloys standardised by CEN/TC 133 4.1 Wrought coppers and copper alloys The product forms and applicable standards are given in Table 10. 4.2 Master alloys The product forms
