1、DEUTSCHE NORM November 2002Luft- und RaumfahrtAnnietmuttern mit MJ-Gewindemit zylindrischer Aussenkung, selbstsichernd, beweglich,einseitiger Flansch, aus Stahl, Klasse: 1 100 MPa/235 C 65243ICS 49.030.30Aerospace Anchor nuts with MJ thread, deep counterbore, self-locking,floating, single lug, steel
2、, classification: 1 100 MPa/235 CAronautique et espace crous river, filetage MJ, chambrageprofond, freinage interne, flottants, simple patte, en acier,classification: 1 100 MPa/235 CErsatz fr(Supersedes)DIN 65243:1987-08In case of dispute the German wording shall bevalid.VorwortDiese Norm wurde von
3、Experten desFachbereiches Mechanik des Normen-ausschusses Luft- und Raumfahrt (NL) unterBercksichtigung gltiger Beschlsse (BuildingBlock Documents) und Normen desISO/TC 20/SC 4 (Aircraft and Space Vehicles Aerospace Fastener Systems) erarbeitet.Der Anhang A ist informativ.ForewordThis standard has b
4、een prepared by theinterested experts of the mechanics section ofNormenausschuss Luft- und Raumfahrt (NL)taking into account relevant resolutions (BuildingBlock Documents) and standards of ISO/TC 20/SC 4 (Aircraft and Space Vehicles AerospaceFastener Systems).The annex A is informative.nderungenGege
5、nber DIN 65243:1987-08 wurden folgendenderungen vorgenommen:a) Die Oberflchenbehandlung 5906 LN 9368-7wurde gendert in 5913 LN 9368-7;b) der Werkstoff 1.7220.3 wurde gendert in1.7224.3;c) in Tabelle 1 wurde der Wert h1= 4 fr dieKennzahl 03 in 4,8 gendert;d) die Norm wurde redaktionell berarbeitet.Am
6、endmentsThe following amendments have been made toDIN 65243:1987-08:a) The surface treatment 5906 LN 9368-7 hasbeen changed in 5913 LN 9368-7;b) the material 1.7220.3 has been changed in1.7224.3;c) in table 1, the value h1= 4 for the code num-ber 03 has been changed in 4,8;d) this standard has been
7、revised editorially.Frhere Ausgaben Previous editionsDIN 65243: 1984-07, 1987-081 AnwendungsbereichDiese Norm legt die Eigenschaften von Anniet-muttern mit MJ-Gewinde, mit zylindrischer Aus-senkung, selbstsichernd, beweglich, einseitigerFlansch, aus Stahl, Klasse 1 100 MPa/235 C beiVerbindungen mit
8、Schrauben mit einer Nennzug-festigkeit von Ga3 1 100 MPa zur Verwendung in derLuft- und Raumfahrt fest.1 ScopeThis standard specifies the characteristics of an-chor nuts with MJ thread, deep counterbore, self-locking, floating, single lug, steel, classification:1 100 MPa/235 C used together with scr
9、ews andbolts of Ga3 1 100 MPa nominal tensile strength foraerospace applications.Fortsetzung Seite 2 bis 7(Continued on pages 2 to 7)Normenausschuss Luft- und Raumfahrt (NL) im DIN Deutsches Institut fr Normung e. V.144 64.21 DIN Deutsches Institut fr Normung e.V. .Jede Art der Vervielfltigung, auch
10、 auszugsweise, Ref. Nr. DIN 65243:2002-11nur mit Genehmigung des DIN Deutsches Institut fr Normung e. V., Berlin, gestattet. Preisgr. 09 Vertr.-Nr. 3009Alleinverkauf der Normen durch Beuth Verlag GmbH, 10772 BerlinB55EB1B3E14C22109E918E8EA43EDB30F09CC9B7EF8DD9NormCD - Stand 2007-03 DIN 65243:2002-11
11、22 Normative VerweisungenDiese Norm enthlt durch datierte oder undatierteVerweisungen Festlegungen aus anderenPublikationen. Diese normative Verweisungen sindan den jeweiligen Stellen im Text zitiert, und diePublikationen sind nachstehend aufgefhrt. Beidatierten Verweisungen gehren spterenderungen o
12、der berarbeitungen dieserPublikationen nur zu dieser Norm, falls sie durchnderung oder berarbeitung eingearbeitet sind.Bei undatierten Verweisungen gilt die letzteAusgabe der in Bezug genommenen Publikation(einschlielich nderungen).2 Normative referencesThis standard incorporates by dated or undated
13、reference, provisions from other publications.These normative references are cited at theappropriate places in the text and the publicationsare listed hereafter. For dated references, sub-sequent amendments to or revisions of any ofthese publications apply to this standard only whenincorporated in i
14、t by amendment or revision. Forundated references the latest edition of thepublication referred to applies (including amend-ments).DIN 29895, Luft- und Raumfahrt Alternativ-Werkstoffe fr Verbindungsteile.DIN 29895, Aerospace Alternative materials forfasteners.DIN V 65900-11, Luft- und Raumfahrt Pass
15、schrauben und Passbolzen Werkstoffe(AECMA-Fachbericht TR 3775:1999).DIN V 65900-11, Aerospace series Bolts andpins Materials (AECMA Technical Report TR 3775:1999).DIN EN 2424, Luft- und Raumfahrt Kenn-zeichnung von Luft- und Raumfahrt-Erzeugnissen;Deutsche Fassung EN 2424:1995.DIN EN 2424, Aerospace
16、 series Marking ofaerospace products; German versionEN 2424:1995.DIN ISO 2768-1, Allgemeintoleranzen Tole-ranzen fr Lngen- und Winkelmae ohneeinzelne Toleranzeintragung; Identisch mitISO 2768-1:1989.DIN ISO 2768-1, General tolerances Tole-rances for linear and angular dimensions withoutindividual to
17、lerance indications; Identical withISO 2768-1:1989.DIN ISO 5855-1, Luft- und Raumfahrt MJ-Gewinde Allgemeine Anforderungen; Identischmit ISO 5855-1:1988.DIN ISO 5855-1, Aerospace MJ threads General requirements; Identical withISO 5855-1:1988.DIN ISO 5855-2, Luft- und Raumfahrt MJ-Gewinde Mae fr Schr
18、auben und Muttern; I-dentisch mit ISO 5855-2:1988.DIN ISO 5855-2, Aerospace MJ threads Limit dimensions for bolts and nuts; Identical withISO 5855-2:1988.LN 9368-1, Luft- und Raumfahrt Bezeichnungder Oberflchenbehandlungen Aufbau der Kenn-Nummern, Angaben in Bauunterlagen, bersicht.LN 9368-1, Aerosp
19、ace Designation of surfacetreatments Composition of identificationnumbers, indications in design documents, survey.LN 9368-5, Luft- und Raumfahrt Bezeichnungder Oberflchenbehandlungen Kenn-Nummern frkathodische Behandlungsverfahren.LN 9368-5, Aerospace Designation of surfacetreatments Identification
20、 numbers for methodsof cathodic treatment.LN 9368-7, Luft- und Raumfahrt Bezeichnung derOberflchenbehandlungen Kenn-Nummern fr Ver-fahren zum Erzeugen von organischen berzgen.LN 9368-7, Aerospace Designation of surfacetreatments Identification numbers for methodsof organic coating.LN 65016, Selbstsi
21、chernde Muttern fr Tempera-turen bis 425 C Technische Lieferbedingungen.LN 65016, Self-locking nuts for temperatures up to425 C Procurement specification.B55EB1B3E14C22109E918E8EA43EDB30F09CC9B7EF8DD9NormCD - Stand 2007-03 DIN 65243:2002-113Werkstoff-Handbuch der Deutschen Luftfahrt,Teil I:German Av
22、iation Materials Manual, Part I:WL 1.7214 Teil 2, Schweibarer Chrom-Molybdn-Vergtungsstahl mit etwa 0,25 C 1 Cr 0,2 Mo Stangen und Schmiedestcke.WL 1.7214 Part 2, Weldable heat-treatable chromium-molybdenum steel with about 0,25 C 1 Cr 0,2 Mo Rods and forgings.WL 1.7224 Teil 1, Luft- und Raumfahrt C
23、hrom-Molybdn-Vergtungsstahl mit etwa 0,35 C 1 Cr 0,2 Mo Stangen und Draht fr kalt oderwarm zu formende Schrauben und Muttern.WL 7224 Part 1, Aerospace Hardened andtempered chromium-molybdenum steel withapprox. 0,35 C 1 Cr 0,2 Mo Bars and wirefor bolts and nuts to be cold or hot formed.3 Anforderunge
24、n 3 Required characteristics3.1 Ausfhrung Mae Masse 3.1 Configuration Dimensions MassNach Bild 1 und Tabellen 1 und 2. See figure 1 and tables 1 and 2.Mae in Millimeter Dimensions in millimetresNicht angegebene Einzelheiten sind zweckent-sprechend zu whlen.Details not specified shall be appropriatel
25、yselected.Allgemeintoleranzen ISO 2768 m General tolerances ISO 2768 mLegende1 Gehuse2 MutterKey1Cage2NutaSicherung durch Verformung nach Wahl des Her-stellersbFlankendurchmessercRadius oder FasedFeld fr KennzeichnungaLocking feature by deformation at manufacturersoptionbPitch diametercRadius or cha
26、mferdArea for markingBild 1 Ausfhrung, Mae(Figure 1 Configuration, dimensions)B55EB1B3E14C22109E918E8EA43EDB30F09CC9B7EF8DD9NormCD - Stand 2007-03 DIN 65243:2002-114Tabelle 1 Mae, Masse(Table 1 Dimensions, mass)Gewinde(Thread) a bacd2d3d4d5d6d7eKennzahl(Codenumber)d1max. max.ohneKappe(withoutcap)mit
27、Kappe(withcap) min. max. Gb1 0,25 max. min.03 MJ3 Gb4 0,5-4H6H 26,5 11 0,5 3,4 4,6 2,5 4,8 4,5 8,504 MJ4 Gb4 0,7-4H6H 26,5 11 0,5 0,45 4,4 6,2 2,5 4,8 6,4 5,5 8,505 MJ5 Gb4 0,8-4H6H 27,5 11 0,7 0,45 5,5 7,3 2,5 4,8 7,7 6,5 9,506 MJ6 Gb4 1-4H5H 30 13,5 0,7 0,45 6,5 8,7 2,5 4,8 8,8 7,5 1108 MJ8 Gb4 1-
28、4H5H 32,7 16 0,75 0,45 8,5 10,9 3 5,7 11,7 9,5 1110 MJ10 Gb4 1,25-4H5H 36,7 18 0,75 10,5 12,9 3,5 6,6 11,5 13aInklusive BeweglichkeitaFloating includedTabelle 1 (fortgesetzt)Table 1 (continued)Gewinde(Thread)f h1h2h3bh4rstyMasseckg/1 000 Stck(Massckg/1 000 pieces)Kennzahl(Codenumber)d1max. max. max.
29、 max. max. max. min.ohneKappe(withoutcap)mitKappe(withcap)03 MJ3 Gb4 0,5-4H6H 8 4,8 4,5 3,5 0,9 1,6 0,15 1,8 04 MJ4 Gb4 0,7-4H6H 8 5,8 4,5 11,8 12,8 3,5 0,9 2,2 0,15 2,0 2,5505 MJ5 Gb4 0,8-4H6H 8 6,9 4,5 11,8 12,8 3,5 0,9 2,4 0,18 2,3 2,9506 MJ6 Gb4 1-4H5H 8 8,1 4,6 12,8 14,3 4 0,9 2,7 0,18 3,8 4,65
30、08 MJ8 Gb4 1-4H5H 8,5 9,9 5,5 16 17,7 4 1,1 2,7 0,2 7,3 9,1510 MJ10 Gb4 1,25-4H5H 8,5 12 6 5 1,1 3 0,23 10,0 bMax. Einschraubtiefe bei Ausfhrung BC und BDcErrechnet mit einer Dichte von 7,85 kg/dm3.bMaximum length of thread engagement for configu-ration BC and BDcCalculated on the basis of a density
31、 of 7,85 kg/dm3.Tabelle 2 Ausfhrung(Table 2 Configuration)Ausfhrung(Configuration)Kennbuchstaben(Code letters)Gewinde-Kennzahl Gb3 03 Ga3 10 ohne Kappe mit glattem Nietloch(Thread code number Gb3 03 Ga3 10 without cap, rivet hole plain)ACohne Kappe mit gesenktem oder gewarztem Nietloch(without cap,
32、rivet hole with dimple or countersink)ADGewinde-Kennzahl Gb3 04 Ga3 08 mit Kappe mit glattem Nietloch(Thread code number Gb3 04 Ga3 08 with cap, rivet hole plain)BCmit Kappe mit gesenktem oder gewarztem Nietloch(with cap, rivet hole with dimple or countersink)BDANMERKUNG Die Ausfhrungen mit Kappe si
33、ndgegenber Gasen und Flssigkeiten nicht dicht.NOTE The configurations with cap are not gas-tightand fluid-tight.B55EB1B3E14C22109E918E8EA43EDB30F09CC9B7EF8DD9NormCD - Stand 2007-03 DIN 65243:2002-1153.2 Werkstoff 3.2 MaterialNach Werkstoff-Handbuch der Deutschen Luft-fahrt, Teil I.According to Germa
34、n Aviation Materials Manual,Part I.Kappe 1.7224.3 nach WL 1.7224 Teil 1 oderund 1.7214.4 nach WL 1.7214 Teil 2Gehuse:Cap 1.7224.3 according to WL 1.7224 Part 1 orand 1.7214.4 according to WL 1.7214 Part 2cage:Mutter: Ausgangswerkstoff:1.7224.3 nach WL 1.7224 Teil 1 oder1.7214.4 nach WL 1.7214 Teil 2
35、Nut: Base material:1.7224.3 according to WL 1.7224 Part 1 or1.7214.4 according to WL 1.7214 Part 2Nach Wahl des Herstellers je nach Herstellungs-art.At manufacturers option depending on the type ofmanufacture.Vergtet auf Hrte HB 370 bis HB 427 oderHV 389 bis HV 449, entspricht einer Zugfestigkeitvon
36、 mindestens 1 250 MPa.Hardened and tempered to hardness HB 370 toHB 427 or HV 389 to HV 449, corresponding to aminimum tensile strength of 1 250 MPa.3.3 Oberflchenbehandlung 3.3 Surface treatmentKappe 3001.2 LN 9368-1 und LN 9368-5,undGehuse:Cap 3001.2 LN 9368-1 and LN 9368-5,andcage:Mutter: 3001.2
37、LN 9368-1 und LN 9368-5 +5913 LN 9368-7:Kennbuchstabe GNut: 3001.2 LN 9368-1 and LN 9368-5 +5913 LN 9368-7:code letter G3.4 Gewinde 3.4 ThreadMJ-Gewinde nach DIN ISO 5855-1 undDIN ISO 5855-2.MJ thread in accordance with DIN ISO 5855-1 andDIN ISO 5855-2.4 Bezeichnung 4 DesignationBEISPIEL EXAMPLEBene
38、nnungsblock(Description block)Identifizierungsblock(Identity block)ANNIETMUTTER(ANCHOR NUT)DIN 65243 AC 05 GNummer dieser Norm(Number of this standard)Ausfhrung (siehe Tabelle 2)Configuration (see table 2)Gewinde-Kennzahl (siehe Tabelle 1)Thread code number (see table 1)Oberflchenbehandlung (siehe 3
39、.3)Surface treatment (see 3.3)5 Kennzeichnung 5 MarkingNach DIN EN 2424, Klasse N. In accordance with DIN EN 2424, style N.Die Kennzeichnung ist vertieft anzubringen. Marking shall be recessed.6 Technische Lieferbedingungen 6 Technical specificationNach LN 65016. n accordance with LN 65016.B55EB1B3E
40、14C22109E918E8EA43EDB30F09CC9B7EF8DD9NormCD - Stand 2007-03 DIN 65243:2002-116Anhang A(informativ)Annex A(informative)A.1 Allgemeines A.1 GeneralDieser Anhang enthlt zustzliche Angaben frdie Fertigung von Annietmuttern auerhalbDeutschlands.This annex contains additional information con-cerning the m
41、anufacture of anchor nuts outsideGermany.Durch unterschiedliche Zulassungsverfahren,Fertigungsmethoden, Werkstoffe usw. sind dieAngaben in dieser Norm ber Annietmuttern freine Fertigung im Ausland nicht immer aus-reichend. So werden dort z. B. Werkstoffe ver-wendet, die wohl dem Normteil im Endzusta
42、nd diegeforderten Eigenschaften gewhrleisten, jedochnicht als gleichwertiger Werkstoff im entsprechen-den Werkstoff-Leistungsblatt des Werkstoff-Hand-buches der Deutschen Luftfahrt, Teil I, angegebensind.Owing to varying approving procedures, produc-tion methods, materials, etc., the details given i
43、nthis standard on anchor nuts are not alwayssufficient for manufacture abroad. For instance,materials are used there which may well ensurethe required characteristics for a standard part inits final state, but which are not listed as equivalentmaterial in the relevant data sheet in the GermanAviatio
44、n Materials Manual, Part I.Die in DIN 29895 und DIN V 65900-11 aufge-fhrten auslndischen Werkstoffe sind durch die inden einzelnen Lndern zustndigen Zulas-sungsstellen als dem deutschen Werkstoff gleich-wertig anerkannt.The foreign materials listed in DIN 29895 andDIN V 65900-11 are approved by the
45、responsiblequalification authorities of the individual countriesas equivalent to the German material.Die im Abschnitt A.3 geforderte Oberflchen-behandlung ist der nach LN 9368-5 und LN 9368-7geforderten gleichwertig.The surface treatment required by clause A.3 isequivalent to that called for by LN 9
46、368-5 andLN 9368-7.A.2 Werkstoff A.2 MaterialAlternativ-Werkstoffe siehe DIN 29895 undDIN V 65900-11.For alternative materials see DIN 29895 andDIN V 65900-11.A.3 Oberflchenbehandlung A.3 Surface treatmentSiehe Tabelle A.1. See table A.1.Tabelle A.1 Gegenberstellung(Table A.1 Comparison)AECMA USA3000.2 LN 9368-53001.2 LN 9368-5EN 21335913 LN 9368-7 EN 2491nachHerstellerangaben(as specified bymanufacturer)B55EB1B3E14C22109E918E8EA43EDB30F09CC9B7EF8