1、April 2009DEUTSCHE NORM English price group 23No part of this standard may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 77.180!$W$D“1520133www.d
2、in.deDDIN EN 15094Safety of machinery Safety requirements for cold flat rolling millsEnglish version of DIN EN 15094:2009-04Sicherheit von Maschinen Sicherheitsanforderungen an KaltflachwalzwerkeEnglische Fassung DIN EN 15094:2009-04www.beuth.deDocument comprises 65 pagesDIN EN 15094:2009-04 2 Start
3、 of validity This standard takes effect on 1 April 2009. National foreword This standard includes safety requirements. This standard has been prepared by Technical Committee CEN/TC 322 “Equipment for making and shaping of metals” (Secretariat: DIN, Germany). The responsible German body involved in i
4、ts preparation was the Normenausschuss Maschinenbau (Mechanical Engineering Standards Committee), Section Htten- und Walzwerkseinrichtungen. Representatives of manufacturers and users of cold flat rolling mills, and of the employers liability insurance associations contributed to this standard. This
5、 standard contains specifications meeting the essential requirements set out in Annex I of the “Machinery Directive”, Directive 98/37/EC (valid until 28 December 2009), and the “revised Machinery Directive”, Directive 2006/42/EC, which takes effect on 29 December 2009, and which apply to machines th
6、at are either first placed on the market or commissioned within the EEA. This standard serves to facilitate proof of compliance with the essential requirements of the directives. Once this standard is cited in the Official Journal of the European Union, it is deemed a “harmonized” standard and thus,
7、 a manufacturer applying this standard may assume compliance with the requirements of the Machinery Directive (“presumption of conformity”). The European Standards referred to in clause 2 and in the bibliography of the EN have been published as the corresponding DIN EN or DIN EN ISO Standards with t
8、he same number. For the International Standards and documents referred to in this standard there are no national standards available unless they have been published as DIN ISO standards with the same number. EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 15094October 2008ICS 77.180English Version
9、Safety of Machinery - Safety requirements for cold flat rollingmillsScurit des machines - Prescriptions de scurit relativesaux laminoirs froid pour produits platsSicherheit von Machinen - Sicherheitsanforderungen anKaltflachwalzwerkeThis European Standard was approved by CEN on 24 August 2008.CEN me
10、mbers are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on applicati
11、on to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the
12、 same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,R
13、omania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2008 CEN All rights of exploitation in any form and by any means reserved
14、worldwide for CEN national Members.Ref. No. EN 15094:2008: EEN 15094:2008 (E) 2 Contents Page Foreword6 Introduction .7 1 Scope 8 2 Normative references 9 3 Terms and definitions .11 4 List of significant hazards 13 5 Safety Requirements and/or measures .13 5.1 General requirements for design, plann
15、ing and risk assessment .13 5.1.1 Planning of cold flat rolling mills .14 5.1.2 Structural assembly 14 5.1.3 Safety layout.14 5.1.4 Access to operating points.14 5.1.5 Access to danger zones15 5.1.6 Guards 15 5.1.7 Guard-rails16 5.1.8 Safety signs and warning devices .16 5.1.9 Safe guarding.16 5.1.1
16、0 Personal protective equipment 16 5.1.11 Electrical equipment16 5.1.12 Hydraulic, pneumatic, cooling and lubrication systems .17 5.1.13 Fluid systems.17 5.1.14 Material to be discharged to drains .17 5.1.15 Surface temperatures and heat radiation17 5.1.16 Pulpits and control stands17 5.1.17 Softwar
17、e manipulation 17 5.1.18 Fire protection17 5.1.19 Ergonomic principles 18 5.1.20 Vibrations .18 5.1.21 Loss of energy .18 5.1.22 Linked Equipment18 5.2 List of significant hazards, hazardous situations, safety requirements and/or measures19 5.2.1 General20 5.2.2 Hydraulics, pneumatics, emulsions and
18、 other pressurised fluid systems .20 5.2.3 Bridges over roller tables and material guides 22 5.2.4 Handling, guiding and transfer equipment (general).23 5.2.5 Roller tables and conveyors.23 5.2.6 Rolling mills, rolling mill stands.24 5.2.7 Pulpits and control stands26 5.2.8 Measuring devices and dis
19、play units 28 5.2.9 Cutting devices 29 5.2.10 Coiling/de-coiling equipment .30 5.2.11 Coil banding machines and marking machines .33 5.3 Additional safety requirements or measures .33 5.3.1 Hold-to-run control device33 5.3.2 Mechanical restraint devices34 5.3.3 Accessible rotating/moving parts34 5.3
20、.4 Particular ergonomic requirements.34 5.4 Noise reduction as a safety requirement 35 5.4.1 Noise reduction at source by design.35 DIN EN 15094:2009-04 EN 15094:2008 (E) 3 5.4.2 Noise reduction by protective measures35 5.4.3 Noise reduction by information .36 5.4.4 Noise sources and examples of noi
21、se reduction measures.36 6 Verification of the safety requirements and/or measures.37 7 Information for use38 7.1 General .38 7.2 Warning devices and safety signs.38 7.3 Minimum marking38 7.4 Accompanying documents.38 7.4.1 Instruction handbook38 7.4.2 Machine/equipment declaration.38 7.4.3 Detailed
22、 information/instructions 39 7.5 Maintenance manual .41 Annex A (normative) Safety requirements and/or measures for electrical equipment and control systems at cold rolling mills 43 A.1 General .43 A.2 Special requirements for controls .43 A.3 Special requirements for shut-down equipment44 A.3.1 Sto
23、p functions/emergency stop functions .44 A.3.2 Selection of stop functions 44 A.3.3 Emergency stop areas 44 A.3.4 Stop functions .45 Annex B (normative) Noise test code .47 B.1 Introduction47 B.2 Determination of A-weighted sound power level.47 B.3 Determination of A-weighted emission sound pressure
24、 levels48 B.3.1 Determination of the emission sound pressure level at specified measuring points .48 B.3.2 Determination of emission sound pressure level at work stations .48 B.4 Measurement uncertainty.48 B.5 Operating conditions 48 B.6 Information to be recorded and reported49 B.7 Declaration and
25、verification of noise emission values .49 Annex C (normative) Protection of persons in case of using asphyxiant gases in fire fighting systems 52 C.1 General .52 C.2 Warning devices 52 C.3 Restraint devices.53 C.4 Preliminary warning time53 C.5 Interrupt device for extinguishing gas 54 C.6 Blocking
26、devices .54 C.7 Pipes .54 C.8 Rooms and adjacent areas.54 C.9 Escape routes 54 C.10 Doors 54 C.11 Marking.55 C.12 Instruction handbook55 Annex D (informative) Example for manufacturers safety instructions for maintenance at cold flat rolling mills 56 D.1 Precautions to reduce hazards caused by .56 D
27、.1.1 Lack of instructions 56 D.1.2 Visual or audible checks at machinery in motion56 D.1.3 Unintentional movements during maintenance .56 D.1.4 Work during standstill with safeguards disabled 57 D.1.5 Work with hazardous substances .57 D.1.6 Plant re-start 57 Annex E (informative) Machines and/or eq
28、uipment covered by this standard 58 DIN EN 15094:2009-04 EN 15094:2008 (E) 4 E.1 Machines and/or equipment covered by this standard but are not limited to 58 E.1.1 Plants 58 E.1.2 Equipment 58 Annex F (informative) Roll spalling .59 F.1 Hazard .59 F.2 Causes 59 F.3 Safety measures 59 Annex G (inform
29、ative) Example for the risk analysis due to interfaces 60 Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 98/37/EC 61 Annex ZB (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 20
30、06/42/EC 62 Bibliography 63 DIN EN 15094:2009-04 EN 15094:2008 (E) 5 Figures Figure 1 Exemplary layout of a cold flat rolling mill 8 Figure G.1 Diagram of a hypothetical plant indicating potentially hazardous interfaces60 Tables Table 1 Significant hazards, hazardous situations, safety requirements
31、and/or measures20 Table 2 Main noise sources of cold flat rolling mills equipment and exemplary noise reduction measures37 Table A.1 Stop functions.45 Table B.1 Example of declared dual-number noise emission values for work stations and specified measuring points 51 DIN EN 15094:2009-04 EN 15094:200
32、8 (E) 6 Foreword This document (EN 15094:2008) has been prepared by Technical Committee CEN/TC 322 “Equipment for making and shaping of metals”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical tex
33、t or by endorsement, at the latest by April 2009, and conflicting national standards shall be withdrawn at the latest by April 2009. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible
34、for identifying any or all such patent rights. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EC Directive(s). For relationship with EC Directive(s), see informative Annex ZA and
35、B, which is an integral part of this document. This European Standard has been elaborated by CEN/TC 322/WG 3, comprising experts from: Denmark, Germany, Italy, Sweden and the United Kingdom. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following coun
36、tries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spa
37、in, Sweden, Switzerland and the United Kingdom. DIN EN 15094:2009-04 EN 15094:2008 (E) 7 Introduction This document is a type C standard as stated in EN ISO 12100. The machinery concerned and the extent to which hazards, hazardous situations and events are covered are indicated in the scope of this
38、standard. When provisions of this type C standard are different from those which are stated in type A or B standards, the provisions of this type C standard take precedence over the provisions of the other standards, for machines that have been designed and built according to the provisions of this
39、type C standard. Where for clarity an example of a preventative measure is given in the text, this should not be considered as the only possible solution. Any other solution leading to the same risk reduction is permissible if an equivalent level of safety is achieved. This European Standard assumes
40、 that the equipment is operated and maintained by trained personnel. DIN EN 15094:2009-04 EN 15094:2008 (E) 8 1 Scope This European Standard specifies the safety requirements for cold rolling mills for flat products (coiled or as heavy plates) as defined in 3.1. This European Standard deals with sig
41、nificant hazards, hazardous situations and events relevant to cold rolling mills for flat products. It deals not only with circumstances where the machinery is used as intended, but also includes other conditions foreseen by the manufacturer, such as foreseeable faults, malfunctions or misuse (see c
42、lauses 4 and 5). This European standard applies to: Machinery and equipment used for the manufacturing of metal cold rolled flat products from the material entry station (1), through the forming stations (2), to the exit (3) (see Figure 1). Key 1 entry section 2 cold rolling mill 3 exit section 4 ro
43、ll changing device 5 border of the plant Figure 1 Exemplary layout of a cold flat rolling mill The following equipment is outside the scope of this European Standard: furnaces in accordance with EN 746-1, EN 746-2 and EN 746-3; pickling plants according to EN 15061; strip processing lines according
44、to EN 15061; abrasive blasting plants according to EN 1248; roll shop equipment; hook conveyors according to EN 619; storage equipment (e. g., high-bay warehouses); cranes, fork lifts, trucks and railway trucks and other vehicles. DIN EN 15094:2009-04 EN 15094:2008 (E) 9 This European Standard is no
45、t applicable to cold rolling mills for flat products, manufactured before the date of publication of this standard by CEN. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undat
46、ed references, the latest edition of the referenced document (including any amendments) applies. EN 349, Safety of machinery Minimum gaps to avoid crushing of parts of the human body EN 574, Safety of machinery - Two-hand control devices - Functional aspects - Principles for design EN 614-1:2006, Sa
47、fety of machinery Ergonomic design principles Part 1: Terminology and general principles EN 614-2, Safety of machinery Ergonomic design principles Part 2: Interactions between the design of machinery and work tasks EN 626-1, Safety of machinery Reduction of risks to health from hazardous substances
48、emitted by machinery Part 1: Principles and specifications for machinery manufacturers EN 842, Safety of machinery Visual danger signals General requirements, design and testing EN 894-1, Safety of machinery Ergonomics requirements for the design of displays and control actuators Part 1: General pri
49、nciples for human interactions with displays and control actuators EN 894-2, Safety of machinery Ergonomics requirements for the design of displays and control actuators Part 2: Displays EN 894-3, Safety of machinery Ergonomics requirements for the design of displays and control actuators Part 3: Control actuators EN 953, Safety of machinery Guards General requirements for the design and construction of fixed and movable guards EN 981, Safety of machinery System of auditory and visual danger and informat
