1、June 2011 Translation by DIN-Sprachendienst.English price group 6No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 91
2、.100.50!$r+h“1790869www.din.deDDIN EN 15818Polymer modified bituminous thick coatings for waterproofing Determination of dimensional stability at high temperatureEnglish translation of DIN EN 15818:2011-06Kunststoffmodifizierte Bitumendickbeschichtungen zur Bauwerksabdichtung Bestimmung der Mabestnd
3、igkeit bei hohen TemperaturenEnglische bersetzung von DIN EN 15818:2011-06Revtements bitumineux pais modifis aux polymres pour impermabilisation Dtermination de la stabilit dimensionnelle haute tempratureTraduction anglaise de DIN EN 15818:2011-06www.beuth.deDocument comprises pagesIn case of doubt,
4、 the German-language original shall be considered authoritative.805.11 DIN EN 15818:2011-06 A comma is used as the decimal marker. National foreword This standard has been prepared by Technical Committee CEN/TC 361 “Project Committee Polymer modified bituminous thick coatings for waterproofing Defin
5、itions/requirements and test methods” (Secretariat: DIN, Germany). The responsible German body involved in its preparation was the Normenausschuss Bauwesen (Building and Civil Engineering Standards Committee), Working Committee NA 005-02-19 AA Kunststoffmodifizierte Bitumendickbeschichtung zur Bauwe
6、rksabdichtung (SpA zu CEN/TC 361). 2 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 15818 March 2011 ICS 91.100.50 English Version Polymer modified bituminous thick coatings for waterproofing - Determination of dimensional stability at high temperature Revtements bitumineux pais modifis aux po
7、lymres pour impermabilisation - Dtermination de la stabilit dimensionnelle haute temprature Kunststoffmodifizierte Bitumendickbeschichtungen zur Bauwerksabdichtung - Bestimmung der Mabestndigkeit bei hohen Temperaturen This European Standard was approved by CEN on 13 February 2011. CEN members are b
8、ound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the
9、 CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centr
10、e has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norwa
11、y, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rights of exploitation in any form a
12、nd by any means reserved worldwide for CEN national Members. Ref. No. EN 15818:2011: EEN 15818:2011 (E) 2 Contents Page Foreword 31 Scope 42 Normative references 43 Terms and definitions .44 Principle 45 Apparatus .46 Test specimens 57 Preparation .58 Procedure .59 Expression of results 510 Test rep
13、ort 5DIN EN 15818:2011-06 EN 15818:2011 (E) 3 Foreword This document (EN 15818:2011) has been prepared by Technical Committee CEN/TC 361 “Project Committee Polymer modified bituminous thick coatings for waterproofing Definitions/requirements and test methods”, the secretariat of which is held by DIN
14、. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2011, and conflicting national standards shall be withdrawn at the latest by September 2011. Attention is drawn to the possibility that
15、some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to i
16、mplement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden,
17、 Switzerland and United Kingdom. DIN EN 15818:2011-06 EN 15818:2011 (E) 4 1 Scope This European Standard specifies a procedure for determining the dimensional stability at a high temperature of polymer modified bituminous thick coatings for waterproofing. 2 Normative references The following referen
18、ced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. FprEN 15814:2011, Polymer modified bituminous thick coatings for water
19、proofing Definitions and requirements ISO 554, Standard atmospheres for conditioning and/or testing Specifications 3 Terms and definitions For the purposes of this document, the terms and definitions given in FprEN 15814:2011 and the following apply. 3.1 coating system bitumen coating material to be
20、 applied to the substrate 3.2 flow resistance stability of polymer modified bituminous thick coating specimens to be suspended vertically with a temperature of (70 2) C without its coating moving 3.3 metal plate plate to which a bitumen coating is applied 4 Principle After coating the substrate, the
21、 specimen is given in a defined temperature of a period of at least 2 h in a vertical position. After that time a visual judgement is made whether there are changes of the coating. 5 Apparatus 5.1 Drying oven. 5.2 Metal plates with a size of approximately 100 mm 100 mm. 5.3 Device (or support), that
22、 allows a vertical position of the metal plates. DIN EN 15818:2011-06 EN 15818:2011 (E) 5 6 Test specimens Two specimens with a size of approximately 100 mm 100 mm. 7 Preparation The metal plate and the components of the polymer bitumen-emulsion shall be conditioned prior the preparation in a normal
23、 climate of (23 2) C and a relative humidity of (50 5) % in accordance with ISO 554. The metal plate has to kept free from any contamination. To provide the specified dry layer thickness the wet coating has to be levelled off with the help of a frame or gauge of the metal plate at room temperature a
24、s specified by the manufacturers instructions. The thickness of the wet layer shall be such as the thickness of the dry layer is (3 0,3) mm. The preparation is to be done without any reinforcement. Then the specimens shall be left in a normal climate of (23 2) C and a relative humidity of (50 2) % f
25、or 28 days. 8 Procedure After 28 days the test specimens shall be placed in a vertical position in a drying oven with a temperature of (70 2) C for a period of at least 2 h. 9 Expression of results After the required period with a visual judgement the specimens has to be controlled whether there are
26、 any changes on the coating surface as drain down of the coating, and slide down of the coating. 10 Test report The test report shall include at least the following information: a) a reference to this European Standard (i.e. EN 15818); b) all details needed to identify the product tested; c) test procedure including: wet layer thickness; dry layer thickness; test temperature; any deviations from the test conditions; DIN EN 15818:2011-06 EN 15818:2011 (E) 6 d) the test results in accordance with Clause 9; e) the date of the tests. DIN EN 15818:2011-06
