DIN EN 61010-2-201-2014 Safety requirements for electrical equipment for measurement control and laboratory use - Part 2-201 Particular requirements for control equipment (IEC 6101.pdf

相关资源

DIN EN 818-7-2008 Short link chain for lifting purposes - Safety - Part 7 Fine tolerance hoist chain Grade T (Types T DAT and DT)(includes Amendment A1 2008) Ge.pdf

DIN EN 1677-3-2008 Components for slings - Safety - Part 3 Forged steel self-locking hooks Grade 8(includes Amendment A1 2008) English version of DIN EN 1677-3 .pdf

DIN EN 1677-2-2008 Components for slings - Safety - Part 2 Forged steel lifting hooks with latch Grade 8(includes Amendment A1 2008) English version of DIN EN 1.pdf

DIN EN 1670-2007 Building hardware - Corrosion resistance - Requirements and test methods English version of DIN EN 1670 2007-06《建筑五金器具 耐腐蚀 要求和试验方法》.pdf

DIN EN 1656-2010 Chemical disinfectants and antiseptics - Quantitative suspension test for the evaluation of bactericidal activity of chemical disinfectants and.pdf

DIN EN 1230-2-2018 Paper and board intended to come into contact with foodstuffs - Sensory analysis - Part 2 Off-flavour (taint) German version EN 1230-2 2009《用.pdf

DIN EN 1176-7-2008 Playground equipment and surfacing - Part 7 Guidance on installation inspection maintenance and operation English version of DIN EN 1176-7 20.pdf

DIN EN 1176-5-2008 Playground equipment and surfacing - Part 5 Additional specific safety requirements and test methods for carousels English version of DIN EN .pdf

DIN EN 1159-1-2007 Advanced technical ceramics - Ceramic composites - Thermophysical properties - Part 1 Determination of thermal expansion (includes Corrigendu.pdf

DIN EN 1093-4-2008 Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 4 Capture efficiency of an exhaust system - Tracer m.pdf

猜你喜欢

DIN 7164-2017 8476 Geometrical product specifications (GPS) - Workshop plug gauges and spherical plug gauges for inside diameters with tolerance class according to DIN EN ISO 286-1.pdf

DIN 7168-1991 General tolerances for linear and angular dimensions and geometrical tolerances (not to be used for new designs)《长度和角度尺寸的一般公差和形位公差 (不适用于新设计)》.pdf

DIN 7172-1991 Tolerances and limit deviations for sizes above 3150 mm up to 10000 mm principles standard tolerances and limit deviations《规格范围在 3150 mm - 10 000 mm 以上的公差和极限偏差 原则、标准公.pdf

DIN 7178-1 Bb 1-1973 System of cone tolerances and cone fits for conical workpieces of cones from C = 1 3 to 1 500 and lenghts from 6 to 630 mm methods for testing of internal an.pdf

DIN 7178-1-1974 System of cone tolerances and cone fits for conical workpieces from C = 1 3 to 1 500 and lengths from 6 to 630 mm system of cone tolerances《锥形工件C=1 3至1 500及长度6至63.pdf

DIN 7178-2-1986 System of cone tolerances and cone fits for conical workpieces of cones from C = 1 3 to 1 500 and lengths from 6 to 630 mm system of cone fits《锥度C=1 3至1 500及长度6至6.pdf

DIN 7178-3-1986 System of cone tolerances and cone fits for conical workpieces of cones from C = 1 3 to 1 500 and lengths from 6 to 630 mm effect of the deviations on cone with r.pdf

DIN 7178-4-1986 System of cone tolerances and cone fits for conical workpieces of cones from C = 1 3 to 1 500 and lengths from 6 to 630 mm axial displacements《锥度C=1 3至1 500及长度6至6.pdf

DIN 7178-5-1976 System of cone tolerances and cone fits for conical workpieces of cones from C = 1 3 to 1 500 and lengths from 6 to 630 mm vocabulary in German English French Ita.pdf