1、February 2015 Translation by DIN-Sprachendienst.English price group 8No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).IC
2、S 25.100.01; 25.060.20!%?cR“2286447www.din.deDDIN ISO 5610-11Tool holders with rectangular shank for indexable inserts Part 11: Style R (ISO 5610-11:2014),English translation of DIN ISO 5610-11:2015-02Klemmhalter mit Vierkantschaft fr Wendeschneidplatten Teil 11: Form R (ISO 5610-11:2014),Englische
3、bersetzung von DIN ISO 5610-11:2015-02Porte-plaquette queue rectangulaire pour plaquettes amovibles Partie 11: Forme R (ISO 5610-11:2014),Traduction anglaise de DIN ISO 5610-11:2015-02SupersedesDIN 4984-11:1987-06www.beuth.deDocument comprises 11 pagesIn case of doubt, the German-language original s
4、hall be considered authoritative.01.15A comma is used as the decimal marker. Contents Page National foreword 3 National Annex NA (informative) Bibliography . 4 1 Scope . 5 2 Normative references 5 3 Dimensions 5 3.1 General 5 3.2 Tool holder style R for square indexable insert shape S 6 4 Designatio
5、n . 8 5 Material 9 6 Design 9 6.1 Type of mounting 9 6.2 Corner radius, r9 6.3 Thickness, s, of indexable insert . 9 7 Extent of delivery . 10 8 Marking 10 Bibliography . 11 2DIN ISO 5610-11:2015-02 National foreword This document (EN ISO 5610-11:2014) has been prepared by Technical Committee ISO/TC
6、 29 “Small tools”, Subcommittee SC 9 “Tools with defined cutting edges, cutting items” (Secretariat: DIN, Germany). The responsible German body involved in its preparation was the DIN-Normenausschuss Werkzeuge und Spannzeuge (DIN Standards Committee Tools and Clamping Devices), Working Committee NA
7、121-01-12 AA Dreh- und Bohrwerkzeuge mit Wendeschneidplatten aus harten Schneidstoffen. This is the first edition of the DIN ISO 5610 series, and replaces the DIN 4984 series, which was the basis for this series of International Standards. Attention is drawn to the possibility that some of the eleme
8、nts of this document may be the subject of patent rights. DIN and/or DKE shall not be held responsible for identifying any or all such patent rights. DIN ISO 5610 consists of the following parts, under the general title Tool holders with rectangular shank for indexable inserts: Part 1: General surve
9、y, correlation and determination of dimensions Part 2: Style A Part 3: Style B Part 4: Style D Part 5: Style F Part 6: Style G Part 7: Style J Part 8: Style K Part 9: Style L Part 10: Style N Part 11: Style R Part 12: Style S Part 13: Style T Part 14: Style H Part 15: Style V The DIN Standard corres
10、ponding to the International Standard referred to in this document is as follows: ISO 6987 DIN ISO 6987 Amendments This standard differs from DIN 4984-11:1987-06 as follows: a) the text of the International Standard has been adopted without any modification. Previous editions DIN 4984-11: 1980-04, 1
11、987-06 3DIN ISO 5610-11:2015-02 National Annex NA (informative) Bibliography DIN 4000-1, Tabular layouts of properties Part 1: Concepts and principles DIN 4000-76, Tabular layouts of properties Part 76: Inserts, indexable DIN 4000-77, Tabular layouts of properties Part 77: Inserts, clamped, for groo
12、ving, parting and thread machining DIN 4000-90, Tabular layouts of properties Part 90: Tool holders for indexable inserts DIN 4967-1, Indexable hardmetal inserts with rounded corners, with partly cylindrical hole 7 normal clearance DIN 4967-2, Indexable hardmetal inserts with rounded corners, with p
13、artly cylindrical hole 11 normal clearance DIN 4968, Indexable hardmetal inserts with rounded corners, without fixation hole DIN 4969-1, Ceramic indexable inserts, with rounded corners, without fixing hole DIN 4983, Tool holders with rectangular shank and cartridges for indexable inserts Presentatio
14、n of the designation DIN 4988, Indexable hardmetal inserts with rounded corners, with cylindrical fixation hole DIN 6580, Terminology of chip removing Movements and geometry of the chip removing process DIN 6581, Terminology of chip removing Reference systems and angles on the cutting part of the to
15、ol DIN 6582, Terminology of cutting Additional terms for the tool, wedge and the cutting edge DIN 6584, Terms of the cutting technique Forces, energy, work, power DIN ISO 6987, Indexable hard material inserts with rounded corners, with partly cylindrical fixing hole Dimensions ISO/TS 13399-201, Cutt
16、ing tool data representation and exchange Part 201: Creation and exchange of 3D models Regular inserts ISO/TS 13399-202, Cutting tool data representation and exchange Part 202: Creation and exchange of 3D models Irregular inserts DIN ISO 5610-11:2015-02 4Tool holders with rectangular shank for index
17、able inserts Part 11: Style R1 ScopeThis part of ISO 5610 specifies tool holders with rectangular shank, style R, i.e. with offset shank and cutting edge angle r= 75 for side cutting.These tool holders are primarily intended for indexable inserts made of hard metal or other cutting materials to be m
18、ounted by clamping and to be used for turning operations.NOTE The symbols for the dimensions shown in the tables of this part of ISO 5610 and the corresponding preferred symbols of properties defined in ISO/TS 13399-2 and ISO/TS 13399-3 are given in ISO 5610-1:2014, Table A.1.2 Normative referencesT
19、he following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 5608:
20、2012, Turning and copying tool holders and cartridges for indexable inserts DesignationISO 5610-1:2014, Tool holders with rectangular shank for indexable inserts Part 1: General survey, correlation and determination of dimensions3 Dimensions3.1 GeneralIt is not necessary for tool holders to comply w
21、ith the pictorial representation; only the dimensions given shall be observed.For determination of dimensions h1, f, and l1, see ISO 5610-1.For explanation of the designation code for tool holders, see ISO 5608.NOTE The values of rake angles and inclination angles shown in the figures are recommende
22、d values; they can vary according to the application.DIN ISO 5610-11:2015-02 53.2 Tool holder style R for square indexable insert shape SKeyaInclination angle, s.bRake angle, o.NOTE This figure shows a right-hand tool holder (R); left-hand tool holder (L) laterally reversed.DIN ISO 5610-11:2015-02 6
23、Figure 1 Tool holder style R for square indexable insert STable 1Dimensions in millimetresSymbolah1b l3a f h2l1al2sbjs13 h13 +050, h13 k16 max.SSRCR 1212 0912 12 9,52 2,2 13 12 323,97SSRCL 1212 09PSRNR 1212 093,18PSRNL 1212 09CSRPR 1212 09CSRPL 1212 09SSRCR 1616 1216 16 12,7 3,1 17 16 36 4,76SSRCL 1
24、616 12PSRNR 1616 12PSRNL 1616 12SSRCR 2020 1220 20 12,7 3,1 22 20 364,76SSRCL 2020 12PSRNR 2020 12PSRNL 2020 12CSRPR 2020 123,18CSRPL 2020 12SSRCR 2525 1225 25 12,7 3,9 27 25 364,76SSRCL 2525 12PSRNR 2525 12PSRNL 2525 12CSRPR 2525 123,18CSRPL 2525 12SSRCR 2525 1525 25 15,88 4,6 27 25 405,56SSRCL 252
25、5 15PSRNR 2525 156,35PSRNL 2525 15SSRCR 3225 1232 25 12,7 3,9 27 32 364,76SSRCL 3225 12PSRNR 3225 12PSRNL 3225 12CSRPR 3225 123,18CSRPL 3225 12aFor the selection of length, l1, the dash can be replaced by the dimensions of ISO 5610-1:2014, Table 2. For letter symbols identifying the tool length, see
26、 ISO 5608:2012, Table 6.bInsert thickness without shim, if applicable.DIN ISO 5610-11:2015-02 7Symbolah1b l3a f h2l1al2sbjs13 h13 +050, h13 k16 max.SSRCR 3225 1532 25 15,88 4,6 27 32 405,56SSRCL 3225 15PSRNR 3225 156,35PSRNL 3225 15SSRCR 3232 1932 32 19,05 4,6 35 32 456,35SSRCL 3232 19PSRNR 3232 19P
27、SRNL 3232 19CSRPR 3232 194,76CSRPL 3232 19SSRCR 4040 1940 40 19,05 4,6 43 40 456,35SSRCL 4040 19PSRNR 4040 19PSRNL 4040 19CSRPR 4040 194,76CSRPL 4040 19PSRNR 4040 2540 40 25,4 5,9 43 40 50 7,94PSRNL 4040 25PSRNR 5050 2550 50 25,4 5,9 53 50 50 7,94PSRNL 5050 25aFor the selection of length, l1, the da
28、sh can be replaced by the dimensions of ISO 5610-1:2014, Table 2. For letter symbols identifying the tool length, see ISO 5608:2012, Table 6.bInsert thickness without shim, if applicable.4 DesignationA tool holder in accordance with this part of ISO 5610 shall be designated by the following:a) “Tool
29、 holder”;b) a reference to this part of ISO 5610 (i.e. ISO 5610-11);c) type of mounting, in accordance with ISO 5608;d) symbol for indexable insert shape, in accordance with ISO 5608;e) symbol for tool style, in accordance with ISO 5608;f) symbol for the indexable insert normal clearance, in accorda
30、nce with ISO 5608;g) symbol for hand of tool, in accordance with ISO 5608;h) its height, h1, width, b, and length, l1(symbol for tool length in accordance with ISO 5608);i) its cutting edge length, l3.Table 1DIN ISO 5610-11:2015-02 8EXAMPLE Tool holder for a horizontally mounted bore-clamped (P) squ
31、are indexable insert shape S (S), tool holder style R (R), for normal clearance of indexable insert n= 0 (N), right-hand type (R), with height h1= 32 mm and width b = 25 mm (3225), length l1= 170 mm (P), for cutting edge length l3= 15,88 mm (15) is designated as follows:Tool holder ISO 5610-11 - PSR
32、NR 3225 P155 MaterialThe material should be steel with a tensile strength of at least 1 200 N/mm2.6 Design6.1 Type of mountingStandard design of tool holders with indexable insert shall be mounted in accordance with Table 1.Other types of mounting are at the manufacturers discretion or upon agreemen
33、t. The letter symbol in the designation, symbol 1, shall then be replaced by the respective symbol for the chosen or agreed-upon type of mounting in accordance with ISO 5608.For the modified type of mounting deviating from Table 1, the relevant indexable insert thickness shall also be considered.6.2
34、 Corner radius, rTool holders in accordance with this part of ISO 5610 can be equipped with indexable inserts with cutting edge length, l3, as specified in Table 1, and any corner radius, r.The values for a and f given in Table 1 and for l1in ISO 5610-1:2014, Table 2, apply to tool holders with inde
35、xable inserts having corner radii, r, in accordance with Table 2.Table 2Dimensions in millimetresl3r9,520,812,715,881,219,0525,4 2,4NOTE The values given for rare nominal values. The accurate values converted from the inch dimensions are 0,794 mm, 1,191 mm, and 2,381 mm.For indexable inserts with co
36、rner radii, r, other than those specified in Table 2, the dimensions a, f, and l1shall be determined in accordance with ISO 5610-1.The tolerances for h1, f, and l1refer to dimensions measured with master indexable insert and master shim, if applicable.6.3 Thickness, s, of indexable insertThe values
37、for thickness, s, given in Table 1 apply to indexable inserts without shim and for the standard design of tool holders.DIN ISO 5610-11:2015-02 9For tool holders for indexable inserts with thicknesses deviating from the specified values, the thickness shall be indicated when ordering or upon delivery
38、 (in the handbook).7 Extent of deliveryTool holders shall be delivered complete with clamping device, but without indexable insert(s).8 MarkingTool holders shall be marked with the letter symbol and the name or trademark of the manufacturer.Additional marking is at the manufacturers discretion or up
39、on agreement.Deviations in marking may be by mutual agreement.A reference to this part of ISO 5610, i.e. ISO 5610-11:2014, shall be given on the packaging.DIN ISO 5610-11:2015-02 10Bibliography1 ISO 883, Indexable hardmetal (carbide) inserts with rounded corners, without fixing hole Dimensions2 ISO
40、3002-1, Basic quantities in cutting and grinding Part 1: Geometry of the active part of cutting tools General terms, reference systems, tool and working angles, chip breakers3 ISO 3364, Indexable hardmetal (carbide) inserts with rounded corners, with cylindrical fixing hole Dimensions4 ISO 6987, Ind
41、exable hard material inserts with rounded corners, with partly cylindrical fixing hole Dimensions5 ISO/TS 13399-2, Cutting tool data representation and exchange Part 2: Reference dictionary for the cutting items6 ISO/TS 13399-3, Cutting tool data representation and exchange Part 3: Reference dictionary for tool itemsDIN ISO 5610-11:2015-02 11
