1、February 2015 Translation by DIN-Sprachendienst.English price group 7No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).IC
2、S 25.100.01; 25.060.20!%?cV“2286451www.din.deDDIN ISO 5610-15Tool holders with rectangular shank for indexable inserts Part 15: Style V (ISO 5610-15:2014),English translation of DIN ISO 5610-15:2015-02Klemmhalter mit Vierkantschaft fr Wendeschneidplatten Teil 15: Form V (ISO 5610-15:2014),Englische
3、bersetzung von DIN ISO 5610-15:2015-02Porte-plaquette queue rectangulaire pour plaquettes amovibles Partie 15: Forme V (ISO 5610-15:2014),Traduction anglaise de DIN ISO 5610-15:2015-02SupersedesDIN 4984-15:2004-07www.beuth.deDocument comprises 9 pagesIn case of doubt, the German-language original sh
4、all be considered authoritative.01.15A comma is used as the decimal marker. Contents Page National foreword 3 National Annex NA (informative) Bibliography . 4 1 Scope . 5 2 Normative references 5 3 Dimensions 5 3.1 General 5 3.2 Tool holder style V for rhombic indexable insert shape V . 6 4 Designat
5、ion . 7 5 Material 7 6 Design 7 6.1 Type of mounting 7 6.2 Corner radius, r8 6.3 Thickness s of indexable insert . 8 7 Extent of delivery 8 8 Marking . 8 Bibliography 9 2DIN ISO 5610-15:2015-02 National foreword This document (EN ISO 5610-15:2014) has been prepared by Technical Committee ISO/TC 29 “
6、Small tools”, Subcommittee SC 9 “Tools with defined cutting edges, cutting items” (Secretariat: DIN, Germany). The responsible German body involved in its preparation was the DIN-Normenausschuss Werkzeuge und Spannzeuge (DIN Standards Committee Tools and Clamping Devices), Working Committee NA 121-0
7、1-12 AA Dreh- und Bohrwerkzeuge mit Wendeschneidplatten aus harten Schneidstoffen. This is the first edition of the DIN ISO 5610 series, and replaces the DIN 4984 series, which was the basis for this series of International Standards. Attention is drawn to the possibility that some of the elements o
8、f this document may be the subject of patent rights. DIN and/or DKE shall not be held responsible for identifying any or all such patent rights. DIN ISO 5610 consists of the following parts, under the general title Tool holders with rectangular shank for indexable inserts: Part 1: General survey, co
9、rrelation and determination of dimensions Part 2: Style A Part 3: Style B Part 4: Style D Part 5: Style F Part 6: Style G Part 7: Style J Part 8: Style K Part 9: Style L Part 10: Style N Part 11: Style R Part 12: Style S Part 13: Style T Part 14: Style H Part 15: Style V The DIN Standard correspondi
10、ng to the International Standard referred to in this document is as follows: ISO 6987 DIN ISO 6987 Amendments This standard differs from DIN 4984-15:2004-07 as follows: a) the text of the International Standard has been adopted without any modification. Previous editions DIN 4984-15:2004-07 DIN ISO
11、5610-15:2015-02 3National Annex NA (informative) Bibliography DIN 4000-1, Tabular layouts of properties Part 1: Concepts and principles DIN 4000-76, Tabular layouts of properties Part 76: Inserts, indexable DIN 4000-77, Tabular layouts of properties Part 77: Inserts, clamped, for grooving, parting a
12、nd thread machining DIN 4000-90, Tabular layouts of properties Part 90: Tool holders for indexable inserts DIN 4967-1, Indexable hardmetal inserts with rounded corners, with partly cylindrical hole 7 normal clearance DIN 4967-2, Indexable hardmetal inserts with rounded corners, with partly cylindric
13、al hole 11 normal clearance DIN 4968, Indexable hardmetal inserts with rounded corners, without fixation hole DIN 4969-1, Ceramic indexable inserts, with rounded corners, without fixing hole DIN 4983, Tool holders with rectangular shank and cartridges for indexable inserts Presentation of the design
14、ation DIN 4988, Indexable hardmetal inserts with rounded corners, with cylindrical fixation hole DIN 6580, Terminology of chip removing Movements and geometry of the chip removing process DIN 6581, Terminology of chip removing Reference systems and angles on the cutting part of the tool DIN 6582, Te
15、rminology of cutting Additional terms for the tool, wedge and the cutting edge DIN 6584, Terms of the cutting technique Forces, energy, work, power DIN ISO 6987, Indexable hard material inserts with rounded corners, with partly cylindrical fixing hole Dimensions ISO/TS 13399-201, Cutting tool data r
16、epresentation and exchange Part 201: Creation and exchange of 3D models Regular inserts ISO/TS 13399-202, Cutting tool data representation and exchange Part 202: Creation and exchange of 3D models Irregular inserts DIN ISO 5610-15:2015-02 4Tool holders with rectangular shank for indexable inserts Pa
17、rt 15: Style V1 ScopeThis part of ISO 5610 specifies tool holders with rectangular shank, style V, i.e. with straight shank and cutting edge angle r= 72,5 for side cutting.These tool holders are primarily intended for indexable inserts made of hard metal or other cutting materials to be mounted by c
18、lamping and to be used for turning operations.NOTE The symbols for the dimensions shown in the tables of this part of ISO 5610 and the corresponding preferred symbols of properties defined in ISO/TS 13399-2 and ISO/TS 13399-3 are given in ISO 5610-1:2014, Table A.1.2 Normative referencesThe followin
19、g documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 5608:2012, Turni
20、ng and copying tool holders and cartridges for indexable inserts DesignationISO 5610-1:2014, Tool holders with rectangular shank for indexable inserts Part 1: General survey, correlation and determination of dimensions3 Dimensions3.1 GeneralIt is not necessary for tool holders to comply with the pic
21、torial representation; only the dimensions given shall be observed.For determination of dimensions h1, f, and l1, see ISO 5610-1.For explanation of the designation code for tool holders, see ISO 5608.NOTE The values of rake angles and inclination angles shown in the figures are recommended values; t
22、hey can vary according to the application.DIN ISO 5610-15:2015-02 53.2 Tool holder style V for rhombic indexable insert shape VKeyaInclination angle, s.bRake angle, o.Figure 1 Tool holder style V for rhombic indexable insert VTable 1Dimensions in millimetresSymbolah1js13bh13l3f0,25h2h13l1ak16l2max.s
23、bSVVBN 1212 11 12 12 11,1 6 12 253,18SVVBN 1616 11 16 16 11,1 8 16 25SVVBN 2020 16 20 20 16,6 10 20 40 4,76aFor the selection of length, l1, the dash can be replaced by the dimensions of ISO 5610-1:2014, Table 2. For letter symbols identifying the tool length, see ISO 5608:2012, Table 6.bInsert thic
24、kness without shim, if applicable.DIN ISO 5610-15:2015-02 6Symbolah1js13bh13l3f0,25h2h13l1ak16l2max.sbSVVBN 2525 16 25 25 16,6 12,5 25 40 4,76SVVBN 3225 16 32 25 16,6 12,5 32 40 4,76aFor the selection of length, l1, the dash can be replaced by the dimensions of ISO 5610-1:2014, Table 2. For letter s
25、ymbols identifying the tool length, see ISO 5608:2012, Table 6.bInsert thickness without shim, if applicable.4 DesignationA tool holder in accordance with this part of ISO 5610 shall be designated by the following:a) “Tool holder”;b) a reference to this part of ISO 5610 (i.e. ISO 5610-15);c) type of
26、 mounting, in accordance with ISO 5608;d) symbol for indexable insert shape, in accordance with ISO 5608;e) symbol for tool style, in accordance with ISO 5608;f) symbol for the indexable insert normal clearance, in accordance with ISO 5608;g) symbol for hand of tool, in accordance with ISO 5608;h) i
27、ts height, h1, width, b, and length, l1(symbol for tool length in accordance with ISO 5608);i) its cutting edge length, l3.EXAMPLE Tool holder for a screw-clamped (S) rhombic indexable insert shape V (V), tool holder style V (V), for normal clearance of indexable insert n= 5 (B), left- and right-han
28、d cutting (N), with height h1= 20 mm and width b = 20 mm (2020), length l1= 125 mm (K), for cutting edge length l3= 11,1 mm (11) is designated as follows:Tool holder ISO 5610-15 - SVVBN 2020 K115 MaterialThe material should be steel with a tensile strength of at least 1 200 N/mm2.6 Design6.1 Type of
29、 mountingStandard design of tool holders with indexable insert shall be mounted in accordance with Table 1.Other types of mounting are at the manufacturers discretion or upon agreement. The letter symbol in the designation, symbol 1, shall then be replaced by the respective symbol for the chosen or
30、agreed-upon type of mounting in accordance with ISO 5608.For the modified type of mounting deviating from Table 1, the relevant indexable insert thickness shall also be considered.Table 1DIN ISO 5610-15:2015-02 76.2 Corner radius, rTool holders in accordance with this part of ISO 5610 can be equippe
31、d with indexable inserts with cutting edge length, l3, as specified in Table 1, and any corner radius, r.The values for l1given in ISO 5610-1:2014, Table 2, apply to tool holders with indexable inserts having corner radii, r, in accordance with Table 2.Table 2Dimensions in millimetresl3r11,1 0,416,6
32、 0,8NOTE The values given for rare nominal values. The accurate values converted from the inch dimensions are 0,397 mm and 0,794 mm.For indexable inserts with corner radii, r, other than those specified in Table 2, the dimension l1shall be determined in accordance with ISO 5610-1.The tolerances for
33、h1, f, and l1refer to dimensions measured with master indexable insert and master shim, if applicable.6.3 Thickness s of indexable insertThe values for thickness s given in Table 1 apply to indexable inserts without shim and for the standard design of tool holders.For tool holders for indexable inse
34、rts with thicknesses deviating from the specified values, the thickness shall be indicated when ordering or upon delivery (in the handbook).7 Extent of deliveryTool holders shall be delivered complete with clamping device, but without indexable insert(s).8 MarkingTool holders shall be marked with th
35、e letter symbol and the name or trademark of the manufacturer.Additional marking is at the manufacturers discretion or upon agreement.Deviations in marking may be by mutual agreement.A reference to this part of ISO 5610, i.e. ISO 5610-15:2014, shall be given on the packaging.DIN ISO 5610-15:2015-02
36、8Bibliography1 ISO 883, Indexable hardmetal (carbide) inserts with rounded corners, without fixing hole Dimensions2 ISO 3002-1, Basic quantities in cutting and grinding Part 1: Geometry of the active part of cutting tools General terms, reference systems, tool and working angles, chip breakers3 ISO
37、3364, Indexable hardmetal (carbide) inserts with rounded corners, with cylindrical fixing hole Dimensions4 ISO 6987, Indexable hard material inserts with rounded corners, with partly cylindrical fixing hole Dimensions5 ISO/TS 13399-2, Cutting tool data representation and exchange Part 2: Reference dictionary for the cutting items6 ISO/TS 13399-3, Cutting tool data representation and exchange Part 3: Reference dictionary for tool itemsDIN ISO 5610-15:2015-02 9
