1、INCH-POUND AA59789/4A 22 July 2010 SUPERSEDING AA59789/4 26 March 2006 COMMERCIAL ITEM DESCRIPTION SPECIFICATION SHEET HOLDER, ELECTRICAL CARD, WEDGE RETAINERS, 5 PIECE, FOR COLD PLATE APPLICATIONS, .225 X .225 INCH BODY SIZE, WITH TWO MOUNTING HOLES, VISUAL LOCK INDICATION, AND SCREW ACTUATION AND
2、RETENTION The General Services Administration has authorized the use of this commercial item description for all federal agencies. The complete requirements for procuring electrical card holders described herein shall consist of this document and the latest issue in effect of AA59789. CLASSIFICATION
3、/PART IDENTIFICATION NUMBER (PIN). This commercial item description (CID) specification sheet uses a classification system which is included in the Part Identification Number (PIN) as shown in the following example (see NOTES). AA59789 CID number /04 Applicable CID sheet * Configuration (see table I
4、) * Finish (see table I) * * Length (see table II) * Mounting (see table I) Example: AA59789/04DE65S is the PIN for a visual lock indicating, electroless nickel finished, 6.3 inch (160.0 mm) long card holder with a retained actuating screw. The card holder also features two tapped mounting holes for
5、 use with 256 UNC 2B fasteners and a combination of a lockwasher, flat washer, and screw self-lock element for added resistance to loosening. SALIENT CHARACTERISTICS. Performance. Card holders shall hold the circuit card firmly in place providing high resistance to shock and vibration while providin
6、g maximum thermal transfer. Interface and physical dimensions. The card holders supplied to this CID specification sheet shall be as specified herein and meet the general requirements specified in CID AA59789. Card holders shall have a visual indicator to show when the assembly is in its relaxed (un
7、locked) and expanded (locked) state. Card holders shall also have a screw retention feature to prevent unintentional disassembly of the card holder. Material. The card holder materials shall be as specified in AA59789. Actuating screw hex drive socket. The dimension for hex drive socket shall be .09
8、4 inch (2.38 mm) across flats for mounting options “S“, “R“, “P“, “U“, and “T“. Cold plate slot width. The recommended slot width for cold plates used with this card holder is .250 inch (6.35 mm) plus the thickness of the circuit card assembly printed board (see AA59789). Installation torque. The re
9、commended nominal installation torque is as follows: 6 inch-pounds (0.68 N-m) for assemblies of configuration “A“, “C“, “F“, or “W“ and 7.2 inch-pounds (0.81 N-m) for assemblies of configurations “D“, “J“, “L“, or “N“. AMSC N/A FSC 5998 Provided by IHSNot for ResaleNo reproduction or networking perm
10、itted without license from IHS-,-,-AA59789/4A 2 Configuration. The configuration of a card holder shall be as specified in table I. The details of a particular configuration consist of those on figures 1, 2, and 3, and may include those on figures 4 and 5. TABLE I. Configurations. Configuration Moun
11、ting body style Finish options Mounting options Applicable figures Hardware options A A B, C, H, P S, R, T, P 1, 2, and 3 No hardware options added C C B, C, E, H S, R, T, U F A B, C, H, P S, R, T, P 1, 2, 3, and 4 Lockwasher and flat washer W C B, C, E, H S, R, T, U N A B, C, H, P S, R, T, P 1, 2,
12、3, and 5 Screw self-lock element L C B, C, E, H S, R, T, U J A B, C, H, P S, R, T, P 1, 2, 3, 4, and 5 Lockwasher, flat washer, and screw self-lock element D C B, C, E, H S, R, T, U Finish. The finish designator shall be as specified in AA59789. The finishes available for this CID specification shee
13、t are as follows: “B“ (black anodize), “C“ (gold chemical film), “E“ (electroless nickel), “P“ (electrodeposited nickel), or “H“ (hard black anodize). The center mounting wedge is not finished for card holders using mounting option “P“. Length, expanded and relaxed dimensions. The length designator
14、shall be as specified in AA59789 and the lengths available for this CID specification sheet are listed in table II. The length, expanded, and relaxed dimensions shall be as specified on figure 1. TABLE II. Additional assembly dimensions (see figure 1). 1/ PIN length designator Dimension “L“ .02 (0.5
15、) Mounting body style Dimension “A“ .01 (0.3) Dimension “B“ .02 (0.5) Dimension “C“ minimum 50 4.8 (121.9) A 1.50 (38.1) .30 (7.6) .275 (6.99) C 1.50 (38.1) .30 (7.6) .275 (6.99) 55 5.3 (134.6) A 2.00 (50.8) .55 (14.0) .275 (6.99) C 1.50 (38.1) .30 (7.6) .275 (6.99) 60 5.8 (147.3) A 2.50 (63.5) .80
16、(20.3) .275 (6.99) C 1.50 (38.1) .30 (7.6) .275 (6.99) 65 6.3 (160.0) A 3.00 (71.2) 1.05 (26.7) .275 (6.99) C 1.50 (38.1) .30 (7.6) .275 (6.99) 1/ Dimensions are in inches. Millimeters are given for information only. Provided by IHSNot for ResaleNo reproduction or networking permitted without licens
17、e from IHS-,-,-AA59789/4A 3 Inches mm Inches mm Inches mm Inches mm .165 .225 4.19 5.72 .235 .30 5.97 7.6 .31 .33 7.9 8.4 .50 .900 12.7 22.86 NOTES: 1. Dimensions are in inches. Millimeter equivalents are given for general information only. 2. Unless otherwise specified, tolerances are for .02 inch
18、(0.51 mm) for two place decimals and .010 (0.25 mm) for three place decimals. 3. The across flats dimension for hex drive socket shall be .094 inch (2.38 mm). 4. Tolerance for the hole spacing is .010 inch (0.25 mm) for mounting body style A and .005 inch (0.51 mm) for mounting body style C. FIGURE
19、1. Relaxed and expanded dimensions. Mounting. The mounting designators shall be as specified in AA59789. The mounting options available for this CID specification sheet are as follows: “S“ (tapped 2-56 holes), “R“ (rivet mount holes with counterbore and countersink), “T“ (tapped 0-80 holes), “P“ (.0
20、62 x .040 index pins), or “U“ (tapped metric M2 x 0.4 holes). See figure 1 for mounting hole spacing requirements. Card holders using mounting option “P“ and “R“ may be shipped unassembled. The center mounting wedge is not finished for card holders using mounting option “P“. Rivet mounting holes. Th
21、e holes used for rivet mounting shall be .066/.073 inch (1.68/1.85 mm) diameter, countersunk 100 degrees by .140 inch (3.56 mm) diameter through holes with a counterbore of .156 inch (3.96 mm) diameter with a depth of .165 inch (4.19 mm) for style C mounting bodies and .175 inch (4.45 mm) for style
22、A mounting bodies. Rivets. This card holder uses rivet type A as specified in AA59789 when rivet mounting is used. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59789/4A 4 Screw retention locknut (see figure 2). Card holders shall have a screw re
23、tention locknut intended to prevent unintentional disassembly of the card holder. The locknut shall be fabricated of a corrosion resistant material. FIGURE 2. Screw retaining self-locking nut (corrosion resistant) details. Visual lock indicator (see figure 3). Card holders shall have a visual indica
24、tor to show when the card holder is in its relaxed (unlocked) state. When the card holder is in the unlocked (relaxed) state, the end of the actuating screw shall display a red band on the side of the screw. When the actuating screw on the card holder has been tightened (assembly expanded) so that t
25、he assembly is in the locked position, this red band shall be concealed. FIGURE 3. Visual lock indicator. Hardware options. Card holders can have the following options: No hardware options added, lockwasher and flat washer (see figure 4), screw self lock element (see figure 4), or lockwasher, flat w
26、asher, and screw self lock element (see figure 4 and 5). See table I for the correct PIN configuration identifier. No hardware options added. The base configuration of the card holder is as depicted by figures 1 and 2 . Card holders not requiring any hardware options shall include configuration iden
27、tifier “A“ or “C“ in the PIN (see classification, notes, and table I). Lockwasher and flat washer (see figure 4). A lockwasher and flat washer located under the screw head will provide for additional resistance to loosening from shock and vibration. Card holders requiring a lockwasher and flat washe
28、r option shall include configuration identifier “F“ or “W“ in the PIN (see classification, notes, and table I). FIGURE 4. Lockwasher and flat washer details. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59789/4A 5 Screw self-locking element (see
29、 figure 5). The use of a screw self-locking element will provide prevailing torque for resistance to loosening from shock vibration. Card holders requiring a screw self-locking element shall include configuration identifier “L“ or “N“ in the PIN (see classification, notes, and table I). FIGURE 5. Sc
30、rew self-locking element details. Lockwasher, flat washer, and screw self-locking element. Card holders requiring a lockwasher, flat washer, and screw self-locking element option shall include configuration identifier “D“ or “J“ in the PIN (see classification, notes, and table I). NOTES. PIN. The PI
31、N should be used for Government purposes to buy commercial products to this CID specification sheet. See the classification section for PIN format example. Source of documents. Commercial Item Description AA59789 Holder, Electrical Card, Wedge Retainers, 5 Piece, For Cold Plate Applications, General
32、 Requirements For. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or https:/assist.daps.dla.mil/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) Ordering data. Ordering data is as specified in
33、 AA59789. Commercial products. As part of the market analysis and research effort, this CID specification sheet was coordinated with the following manufacturers of commercial products. At the time of CID specification preparation and coordination, these manufacturers were known to have commercial pr
34、oducts that would meet the requirements of this CID specification sheet. (NOTE: This information should not be considered as a list of approved manufacturers or be used to restrict procurement to only the manufacturers shown.) Provided by IHSNot for ResaleNo reproduction or networking permitted with
35、out license from IHS-,-,-AA59789/4A 6 Manufacturer CAGE Manufacturer name and address Manufacturer contact information 18915 Birtcher A Division of Pentair Electronic Packaging 7238 Trade Street San Diego, CA 921213410 Telephone: (858) 7402400 Toll Free: (800) 8547086 Facsimile: (858) 6794555 (URL):
36、 52094 Calmark A Division of Pentair Electronic Packaging 7238 Trade Street San Diego, CA 921213410 Telephone: (858) 7402400 Toll Free: (800) 8547086 Facsimile: (858) 7402430 Electronic mail: URL: 5BG68 Card Locks Unlimited, Inc. 2310 E. Orangethorpe Avenue Anaheim, CA 928061231 Telephone: (714)
37、7386194 Facsimile: (714) 4460119 E-mail: URL: Part number supersession data. This CID specification sheet PINs supersedes the following manufacturers part numbers as shown in table III. The CID PINs listed in table IV are only for length designator “50“. See table IV for CID PIN construction using
38、 other available lengths for this CID specification sheet. This information is being provided to assist in reducing proliferation in the Government inventory system. TABLE III. Commercial part number supersession data. PIN designator AA59789/04 Vendor similar designator or type part number 1/ CAGE 1
39、8915 PIN designator AA59789/04 Vendor similar designator or type part number 1/ CAGE 52094 Vendor similar designator or type part number 1/ CAGE 5BG68 AB50S 425VI10BLN CB50S VA231CR4.80T2R 5231VBA4.80T2R AB50R 425VI10BLNR CB50R VA231CR4.80HR 5231VBA4.80HR AB50T 425VI10BLNT CB50T VA231CR4.80T0R 5231V
40、BA4.80T0R AB50P 425VI10BLNP CB50U VA231CR4.80TM2R 5231VBA4.80TM2R FB50S 425VI10BLFLN WB50S WVA231CR4.80T2R 5231VWBA4.80T2R FB50R 425VI10BLFLNR WB50R WVA231CR4.80HR 5231VWBA4.80HR FB50T 425VI10BLFLNT WB50T WVA231CR4.80T0R 5231VWBA4.80T0R FB50P 425VI10BLFLNP WB50U WVA231CR4.80TM2R 5231VWBA4.80TM2R NB5
41、0S 425VI10BLNL LB50S VA231CR4.80T2LR 5231VBA4.80T2LR NB50R 425VI10BLNRL LB50R VA231CR4.80HLR 5231VBA4.80HLR NB50T 425VI10BLNTL LB50T VA231CR4.80T0LR 5231VBA4.80T0LR NB50P 425VI10BLNPL LB50U VA231CR4.80TM2LR 5231VBA4.80TM2LR JB50S 425VI10BLFLNL DB50S WVA231CR4.80T2LR 5231VWBA4.80T2LR JB50R 425VI10BLF
42、LNRL DB50R WVA231CR4.80HLR 5231VWBA4.80HLR JB50T 425VI10BLFLNTL DB50T WVA231CR4.80T0LR 5231VWBA4.80T0LR JB50P 425VI10BLFLNPL DB50U WVA231CR4.80TM2LR 5231VWBA4.80TM2LR See footnote at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA597
43、89/4A 7 TABLE III. Commercial part number supersession data Continued. PIN designator AA59789/04 Vendor similar designator or type part number 1/ CAGE 18915 PIN designator AA59789/04 Vendor similar designator or type part number 1/ CAGE 52094 Vendor similar designator or type part number 1/ CAGE 5BG
44、68 AC50S 425VI10LN CC50S V231CR4.80T2R 5231VCG4.80T2R AC50R 425VI10LNR CC50R V231CR4.80HR 5231VCG4.80HR AC50T 425VI10LNT CC50T V231CR4.80T0R 5231VCG4.80T0R AC50P 425VI10LNP CC50U V231CR4.80TM2R 5231VCG4.80TM2R FC50S 425VI10LFLN WC50S WV231CR4.80T2R 5231VWCG4.80T2R FC50R 425VI10LFLNR WC50R WV231CR4.8
45、0HR 5231VWCG4.80HR FC50T 425VI10LFLNT WC50T WV231CR4.80T0R 5231VWCG4.80T0R FC50P 425VI10LFLNP WC50U WV231CR4.80TM2R 5231VWCG4.80TM2R NC50S 425VI10LNL LC50S V231CR4.80T2LR 5231VCG4.80T2LR NC50R 425VI10LNRL LC50R V231CR4.80HLR 5231VCG4.80HLR NC50T 425VI10LNTL LC50T V231CR4.80T0LR 5231VCG4.80T0LR NC50P
46、 425VI10LNPL LC50U V231CR4.80TM2LR 5231VCG4.80TM2LR JC50S 425VI10LFLNL DC50S WV231CR4.80T2LR 5231VWCG4.80T2LR JC50R 425VI10LFLNRL DC50R WV231CR4.80HLR 5231VWCG4.80HLR JC50T 425VI10LFLNTL DC50T WV231CR4.80T0LR 5231VWCG4.80T0LR JC50P 425VI10LFLNPL DC50U WV231CR4.80TM2LR 5231VWCG4.80TM2LR AP50S 425VI10
47、NLN CE50S VEN231CR4.80T2R 5231VEN4.80T2R AP50R 425VI10NLNR CE50R VEN231CR4.80HR 5231VEN4.80HR AP50T 425VI10NLNT CE50T VEN231CR4.80T0R 5231VEN4.80T0R AP50P 425VI10NLNP CE50U VEN231CR4.80TM2R 5231VEN4.80TM2R FP50S 425VI10NLNLF WE50S WVEN231CR4.80T2R 5231VWEN4.80T2R FP50R 425VI10NLFLNR WE50R WVEN231CR4
48、.80HR 5231VWEN4.80HR FP50T 425VI10NLFLNT WE50T WVEN231CR4.80T0R 5231VWEN4.80T0R FP50P 425VI10NLFLNP WE50U WVEN231CR4.80TM2R 5231VWEN4.80TM2R NP50S 425VI10NLNL LE50S VEN231CR4.80T2LR 5231VEN4.80T2LR NP50R 425VI10NLNRL LE50R VEN231CR4.80HLR 5231VEN4.80HLR NP50T 425VI10NLNTL LE50T VEN231CR4.80T0LR 5231VEN4.80T0LR NP5
