1、Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any data that may improve this document should be sent to: STDZNMGTdla.mil or Defense Supply Center Richmond (DSCR), ATTN: DSCR-VEB, 8000 Jefferson Davis Highway, Richmond, VA 23297-5616. Since contact information c
2、an change, you may want to verify the currency of this address information using the ASSIST database at https:/assist.daps.dla.mil/. FSC 6240 INCH-POUND A-A-52409A 21 April 2010 SUPERSEDING A-A-52409 3 November 1992 COMMERCIAL ITEM DESCRIPTION LAMPS, INCANDESCENT, SEALED BEAM The General Services Ad
3、ministration has authorized the use of this commercial item description for all federal agencies. 1. SCOPE. This commercial item description (CID) covers requirements for incandescent sealed beam lamps which provide illumination of the road and its environment. 2. SALIENT CHARACTERISTICS 2.1 Incande
4、scent sealed beam lamps. Unless otherwise specified herein, the salient characteristics and markings for incandescent sealed beam lamps shall conform to SAE J1383. 2.2 Characteristics. The physical and electrical characteristics of the incandescent sealed beam lamps are as specified in figures 1 thr
5、ough 4. 2.3 Workmanship. Workmanship shall be in accordance with the manufacture of high quality incandescent sealed beam lamps. This shall be evidenced by the absence of defects which are detrimental to the appearance, serviceability, or durability of the headlamps such as: surface deterioration, f
6、ractures, color bleeding, deterioration of bonding material, exterior or internal corrosion. 2.4 Materials. The use of recovered material made in compliance with regulatory requirements is acceptable providing that all requirements of this CID are met (see 3.1). Provided by IHSNot for ResaleNo repro
7、duction or networking permitted without license from IHS-,-,-A-A-52409A 2 3. REGULATORY REQUIREMENTS 3.1 Recovered materials. The offeror/contractor is encouraged to use recovered materials to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (
8、FAR). 4. PRODUCT CONFORMANCE PROVISIONS 4.1 Product conformance. The products provided shall meet the salient characteristics of this CID, conform to the producers own drawings, specifications, standards, and quality assurance practices, and be the same product offered for sale in the commercial mar
9、ketplace. The government reserves the right to require proof of such conformance. 4.2 Market acceptability. The products offered must have been previously sold either to the government or on the commercial market. 5. PACKAGING 5.1 Preservation, packing, and marking. Preservation, packing, and markin
10、g shall be as specified in the acquisition order (see 6.3(b). 6. NOTES 6.1 Part or identification number (PIN). The following PIN procedure is for government purposes and does not constitute a requirement for the contractor. Example of reference part number: AA52409-4435 indicates an incandescent se
11、aled beam spot lamp rated 12 volts, 30 watts, filament type CC-6, with an average lab life of 100 hours. 6.2 Sources of documents. 6.2.1 FAR. The FAR may be obtained from the Superintendent of Documents, P.O. Box 371954, Pittsburgh, PA 15250-7954. Electronic copies may be obtained from https:/www.ac
12、quisition.gov/far/. 6.2.2 Federal CIDs. Copies of federal CIDs may be obtained from General Services Administration, Federal Supply Service, Specification Section, 470 East LEnfant Plaza SW, Suite 8100, Washington, DC 20407. Electronic copies may be obtained from https:/assist.daps.dla.mil/. Commerc
13、ial trade number (see figures 1 thru 4) AA52409 - XXXX CID number Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52409A 3 6.2.3 ASTM standards. Copies of ASTM standards may be obtained from ASTM International, 100 Barr Harbor Drive, P.O. Box C70
14、0, West Conshohocken, PA 19428-2959. Electronic copies may be obtained from http:/www.astm.org/. 6.2.4 IEEE standards. Copies of IEEE standards may be obtained from the Institute of Electrical and Electronics Engineers, Inc., 445 Hoes Lane, Piscataway, NJ 08854-1331. Electronic copies may be obtaine
15、d from http:/www.ieee.org/. 6.2.5 SAE standards. Copies of SAE standards may be obtained from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001. Electronic copies may be obtained from http:/www.sae.org/. 6.3 Ordering data. The acquisition order should specify the following informa
16、tion: a. CID document number, revision, and CID PIN. b. Preservation, packing, and marking (see 5.1). 6.4 Metric products. Incandescent sealed beam lamps that are manufactured to metric dimensions will be considered on the following basis: a. Products manufactured to metric dimensions will be consid
17、ered on an equal basis with those manufactured using inch-pound units provided they fall within specified tolerances of IEEE/ASTM SI 10, “American National Standard for Use of the International System of Units (SI): The Modern Metric System“, and all other requirements of this CID are met. b. If a p
18、roduct is manufactured to metric dimensions and those dimensions exceed the tolerances specified in the inch/pound units, a request should be made to the contracting officer to determine if the product is acceptable. c. The contracting officer has the option of accepting or rejecting the product. 6.
19、5 Cross-reference data. Incandescent sealed beam lamps conforming to this CID are interchangeable/substitutable with incandescent sealed beam lamps conforming to MS18005, MS18006, MS18007, MS18008B, and MS18010A. 6.6 Subject term (key word) listing. Bulb Floodlight Headlamp Headlight Searchlight Spo
20、tlight Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52409A 4 Rated Design PIN no. Former MS part no. Former part no. Volts Watts Volts Amps Filament type Rated avg. lab life AA52409-4435 MS18005-4435 ORD 446660 12.0 30.0 12.8 2.34 CC-6 100 hrs
21、. AA52409-4525 MS18005-4525 - 3.7 2.2 3.7 0.60 C-6 200 hrs. AA52409-4530 MS18005-4530 ORD 193141 24.0 135.0 26.0 5.20 4CC-8 50 hrs. AA52409-4533 MS18005-4533 ORD 193138 6.0 40.0 6.5 6.20 5C-8 50 hrs. AA52409-4535 MS18005-4535 ORD 444279 6.0 30.0 6.4 4.69 C-6 100 hrs. AA52409-4572 MS18006-4572 ORD 57
22、3141 24.0 150.0 28.0 5.36 CC-6 300 hrs. Description: Clear glass lens, PAR46, filament shield for all except AA52409-4525 and AA52409-4572 AA52409-4525 - Clear glass lens, PAR46 AA52409-4572 - Clear glass prismatic lens, PAR46 NOTES: 1. Dimensions are in inches. 2. Untoleranced dimensions are nomina
23、l and to be used for reference only. FIGURE 1. Incandescent sealed beam spot/flood lamps, 2-screw terminal type. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52409A 5 Rated Design PIN no. Former MS part no. Volts Watts Volts Amps Filament type
24、 Rated avg. lab life AA52409-4541 MS18007-4541 28 450 28 16.1 C-13 25 hrs. Description: Clear glass lens, PAR56, filament shield NOTES: 1. Dimensions are in inches. 2. Untoleranced dimensions are nominal and to be used for reference only. FIGURE 2. Incandescent sealed beam spot lamp, 2-screw termina
25、l type. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52409A 6 Rated Design PIN no. Former MS part no. Army former part no. Volts Watts Volts Amps Filament type Rated avg. lab life AA52409-4863 MS18008-4863 7998618 24 80/60 28/28 2.86/2.14 CC6/
26、CC6 400 hrs. Description: Clear glass prismatic lens, PAR56, filament shield NOTES: 1. Dimensions are in inches. 2. Tolerances are .010 unless otherwise specified. 3. Boot material shall be made of rubber. 4. The 3 cables shall be made of 14 gauge wire. 5. Contact pins to be used shall be in accorda
27、nce with A-A-52536, “Contact, Electrical No. 12, 14, and 16 A.W.G.“. FIGURE 3. Incandescent sealed beam headlamp, 3-cable type. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52409A 7 Rated Design PIN no. Former MS part no. Volts Watts Volts Amp
28、s Filament type Rated avg. lab life AA52409-4801 MS18010-4801 24 80/60 28/28 2.86/2.14 CC6/CC6 400 hrs. Description: Clear glass prismatic lens, PAR56, filament shield NOTES: 1. Dimensions are in inches. 2. Tolerances are .010 unless otherwise specified. FIGURE 4. Incandescent sealed beam headlamp,
29、3-contact lug type. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52409A 8 MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY:Custodians: GSA - FAS Army - AT Navy - YD Air Force - 99 DLA - GS Review Activities: Navy - SH Air Force - 11, 71
30、Preparing Activity: DLA - GS2 (Project 6240-2010-001) NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST database at https:/assist.daps.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
