1、Beneficial comments recommendations, additions, deletions, clarifications, etc., and any data which may improvethis document should be addressed to: Defense Supply Center, Columbus, ATTN: DSCC-VAT, Post Office Box3990, Columbus, OH 43213-1199, or telephone (614) 692-0562, or facsimile (FAX) (614) 69
2、3-1644.AMSC N/A FSC 5915DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.INCH-POUNDA-A-55166BSeptember 17, 2001SUPERSEDINGA-A-55166AApril 29, 1994COMMERCIAL ITEM DESCRIPTIONFILTER, RADIO FREQUENCY INTERFERENCEThe General Services Administration has authorized the use
3、of thiscommercial item description (CID) for all federal agencies as areplacement for Federal Specification W-F-2190/6.1. SCOPE. This CID covers the general requirements for radio frequency interference (RFI) suppression power linefilters. These filters consist of capacitors and inductors used in co
4、mbination with each other and are provided withresistors as a safety feature. Filters covered by this CID are intended for commercial/industrial applications andshould not be used in military systems needing stringent environmental and electrical requirements.2. CLASSIFICATION. This CID uses a class
5、ification system which is included in the Part Identification Number(PIN) as shown in the following example (see 7.1).AA55166 -01CID number Dash number3. SALIENT CHARACTERISTICS.3.1 Interface and physical dimensions. Filters supplied to this CID shall be as specified herein (see figures 1 and 2).3.2
6、. Voltage rating. The voltage rating shall be 120 V ac at 60 Hz; 250 V ac at 50 Hz.3.3 Operating frequency. The operating frequency shall be 50/60 Hz.3.4 Current rating. The current rating shall be as specified in table I.3.5 Operating ambient temperature range. The operating ambient temperature ran
7、ge shall be -10G01C to +40G01C atrated current.3.6 Maximum leakage current, line-to-ground. The maximum leakage current, line-to-ground, shall be 0.5 mA at120 V ac, 60 Hz; 1.0 mA at 250 V ac, 50 Hz.3.7 Hipot rating (1 minute). The hipot rating shall be 2,250 V dc line-to-ground; 1,450 V dc line-to-l
8、ine.3.8 Insertion loss. Insertion loss is given for line-to-ground in a 50-ohm circuit. Values shall be as specified in table I.3.9 Electrical schematics. The electrical schematics shall be as specified on figure 1.3.10 Marking. Filters supplied to this CID shall be marked with the manufacturers (MF
9、Rs) standard commercialPIN.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55166B2TABLE I. Current rating and insertion loss.Minimum insertion loss (dB)Line-to-ground in 50 -ohm circuitFrequency (MHz)PINAA55166-Current rating Electricalschematic.
10、15.5 1 5 103001 10 A A 7202540454802 10 A B 6192842455003 20 A A 7202540454804 20 A B 6192842455005 30 A A 7202540454806 30 A B 61928424550Schematic A Schematic BFIGURE 1. Electrical schematics.Case style AFIGURE 2. Case configuration and dimensions.Provided by IHSNot for ResaleNo reproduction or ne
11、tworking permitted without license from IHS-,-,-A-A-55166B3Case style BA(max)B(max)C(max)DG02.015/G02.38E(max)PINAA55166-Inch mm Inch mm Inch mm Inch mm Inch mmCasestyle01 2.72 69.1 1.82 46.2 1.16 29.5 2.125 53.98 2.53 64.3 A02 3.46 87.9 2.07 52.6 1 16 29.5 2.375 60.33 2.81 71.4 A03 3.46 87.9 2.07 5
12、2.6 1.16 29.5 2.375 60.33 2.81 71.4 A04 3.46 87.9 2.56 65.0 1.53 38.9 2.938 74.63 3.35 85.1 A05 5.34 135.6 3.38 85.9 1.53 38.9 3.750 95.25 4.20 106.7 B06 5.34 135.6 3.38 85.9 1.53 38.9 3.750 95.25 4.20 106.7 BNOTES:1. Dimensions are in inches.2. Metric equivalents are given for general information o
13、nly.3. Terminals: (Five) No. 8-32.4. Mounting holes for -1 through -04: (Two) .188 inch (4.78 mm) diameter.Mounting slots for -05 and -06: (Four) .250 inch (6.35 mm) x .156 inch (3.96 mm).5. Metric equivalents are in parentheses.FIGURE 2. Case configuration and dimensions - Continued.Provided by IHS
14、Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55166B44. REGULATORY REQUIREMENTS. The offeror/contractor is encouraged to use recovered materials to themaximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR).
15、5. PRODUCT CONFORMANCE PROVISIONS5.1 Product conformance. The products provided shall meet the salient characteristics of this CID, conform to theproducers own drawings, specifications, standards, and quality assurance practices, and be the same productoffered for sale in the commercial market. The
16、Government reserves the right to require proof of such conformance.6. PACKAGING. Preservation, packing, and marking shall be as specified in the contract or order.7. NOTES.7.1 PIN. The PIN should be used for Government purposes to buy commercial products to this CID. See section 2for PIN format exam
17、ple.7.2 Commercial and Government Entity (CAGE) code. For ordering purposes, inventory control, and submission ofthese filters to DSCC under the Military Parts control Advisory Group (MPCAG) evaluation program, CAGE code58536 should be used.7.3 Source of documents. This section is not applicable to
18、this CID.7.4 Ordering data. The contract or order should specify the following:a. CID document number, revision, and CID PIN.b. Product conformance provisions.c. Packaging requirements.7.5 Commercial products. As part of the market analysis and research effort, this CID was coordinated with thefollo
19、wing manufacturers of commercial products. At the time of CID preparation and coordination, thesemanufacturers were known to have commercial products that would meet the requirements of this CID. (NOTE:This information should not be considered as a list of approved manufacturers or be used to restri
20、ct procurement toonly the manufacturers shown.)MFRs CAGE MFRs name and address0S2B1 RME Filters, IncorporatedP. O. Box 83898 Route 101 AAmherst, NH 03031-083805245 CORCOM, Incorporated844 East Rockland RoadLibertyville, IL 60048Provided by IHSNot for ResaleNo reproduction or networking permitted wit
21、hout license from IHS-,-,-A-A-55166B57.6 Part number (PIN) supersession data. This CID supersedes the following manufacturers PINs as shown. Thisinformation is being provided to assist in reducing proliferation in the government inventory system.TABLE II. PIN supersession data.MFRs CAGE0S2B1MFRs CAG
22、E05245PINAA55166- MFRs Commercial PIN 1/01 RME-A-110-S 10VB602 RME-A-210-S 10VK603 RME-A-120-S 20VB604 RME-A-220-S 20VK605 RME-A-130-S 30VB606 RME-A-230-S 30VK61/ The manufacturers PIN shall not be used for procurement to the requirementsof this CID. At the time of preparation of this CID, the afore
23、mentioned commercialproducts were reviewed and could be replaced by the CID PIN shown. For actualpart marking requirements, see 3.11.7.7 Government users. To acquire information on obtaining these filters from the Government inventory system,contact Defense Supply Center Columbus, ATTN: DSCC-VAT, Po
24、st Office Box 3990, Columbus, OH 43216-5000,telephone (614) 692-0562 or facsimile (614) 693-1644.7.7.1 National stock number (NSN). The following is a list of NSNs assigned which correspond to this CID. The listis for information only and may not be indicative of all possible NSNs associated with th
25、e CID. For up to dateinformation on assigned NSNs, please contact the aforementioned DSCC office (See 7.7).TABLE III. NSNs.PINAA55166-NSN01 -02 -03 -04 5915-01-455-311805 -06 -MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY:GSA - 7FXECustodians:Navy - EC Preparing Activity:DLA-CCProject 5915-0405Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
