1、Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any data that may improve this document should be sent to: STDZNMGTdla.mil or Defense Supply Center Richmond (DSCR), ATTN: DSCR-VEB, 8000 Jefferson Davis Highway, Richmond, VA 23297-5616. AMSC N/A FSC 5940 INCH-POUN
2、D A-A-59555A 22 March 2007 SUPERSEDING A-A-59555 23 June 2000 COMMERCIAL ITEM DESCRIPTION POST, BINDING, ELECTRICAL, WATERPROOF (INSULATED), TOP ENTRY The General Services Administration has authorized the use of this commercial item description for all federal agencies. 1. SCOPE. This commercial it
3、em description (CID) covers an insulated electrical binding post used as a wiring termination on terminal boards and test set panels. 2. CLASSIFICATION. The electrical binding post shall be classified and identified by the type in accordance with the characteristics specified in table I. The selecte
4、d product to be supplied shall be specified in the acquisition order (see 7.3(b). TABLE I. Electrical binding post (waterproof) dimensions. Dimensions Type Insulation color A1 (max.) B1 (max.) C1 (max. dia.)D1 ThreadE1 (0.001) F1 (0.002) I Olive drab (or as specified) 1.612 1.072 0.400 8-36 UNF-2A0.
5、241 0.272 1See figure 1. 3. SALIENT CHARACTERISTICS 3.1 Components. The electrical binding post shall be similar to the one shown in figure 1. The product shall consist of the binding post, insulated spring-loaded cap, insulated mounting washers, o-ring, and all mounting hardware. Provided by IHSNot
6、 for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59555A 2 CHEX NUT NO. 8-36UNF-2B X0.125 X 0.344ACROSS FLATSDEPRESS CAP TOINSERT WIREFACILITY FOR 0.086 MAX WIREFACILITY FOR0.080 TEST PRODSEE NOTE 2“O“ RINGDEF0.062 MAX WIREBANOTES: 1. The figure depicts only general
7、 characteristics and is not intended to limit specific manufacturing processes. 2. This is the insulated portion. 3. Dimensions (listed in table I) are in inches. Tolerance is 0.015 inch unless otherwise shown. FIGURE 1. Binding post configuration. 3.2 Materials. 3.2.1 Metal. Unless specified otherw
8、ise in the acquisition order (see 7.3(c), the current-carrying portions of the binding post shall be brass conforming to the requirements of ASTM B16/B 16M, “Standard Specification for Free-Cutting Brass Rod, Bar and Shapes for Use in Screw Machines“. 3.2.2 Finish. Unless otherwise specified in the
9、acquisition order (see 7.3(d), metal portions of the binding post shall be nickel plated in accordance with SAE AMS-QQ-N-290, “Nickel Plating (Electrodeposited)“. 3.2.2.1 Solder coating. Unless otherwise specified in the acquisition order (see 7.3(e), the solder terminal end shall be hot solder dipp
10、ed/coated. 3.2.3 Insulation. The material used for the insulated portions of the binding post shall be specified in the acquisition order (see 7.3(f). The insulated parts of an individual binding post shall all be of the same color and unless otherwise specified in the acquisition order (see 7.3(g),
11、 the color shall be olive drab. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59555A 3 3.3 Cap and cap spring. The cap shall be insulated and non-removable. The strength of the cap spring shall permit the cap to be depressed using a force of 3
12、to 5 pounds. 3.4 Non-turn feature. Unless otherwise specified in the acquisition order (see 7.3(h), the non-turn feature shall be a flattened boss on the molded-on insulated piece configured to fit the typical mounting hole as shown in figure 2 and oriented with respect to the wire and probe opening
13、s as shown in figure 1. 0.2820.2780.2490.245FIGURE 2. Typical mounting hole. 4. REGULATORY REQUIREMENTS 4.1 Recovered materials. The offeror/contractor is encouraged to use recovered materials to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulatio
14、n (FAR). 5. PRODUCT CONFORMANCE PROVISIONS 5.1 Product conformance. The products provided shall meet the salient characteristics of this CID, conform to the producers own drawings, specifications, standards, and quality assurance practices, and be the same product offered for sale in the commercial
15、marketplace. The government reserves the right to require proof of such conformance. 5.2 Market acceptability. The product offered must have been previously sold either to the government or on the commercial market. Provided by IHSNot for ResaleNo reproduction or networking permitted without license
16、 from IHS-,-,-A-A-59555A 4 6. PACKAGING 6.1 Preservation, packing, and marking. Preservation, packing, and marking shall be as specified in the acquisition order (see 7.3(i). 7. NOTES 7.1 Part or identification number (PIN). The following PIN procedure is for government purposes and does not constit
17、ute a requirement for the contractor. 7.2 Sources of documents. 7.2.1 FAR. The FAR may be obtained from the Superintendent of Documents, P.O. Box 371954, Pittsburgh, PA 15250-7954. Electronic copies of FAR documents may be obtained from http:/www.arnet.gov/far/. 7.2.2 ASTM standards. Copies of ASTM
18、standards may be obtained from ASTM International, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959. Electronic copies of ASTM standards may be obtained from http:/www.astm.org/. 7.2.3 SAE standards. Copies of SAE standards may be obtained from SAE International, 400 Commonweal
19、th Drive, Warrendale, PA 15096-0001. Electronic copies of SAE standards may be obtained from http:/www.sae.org/. 7.3 Ordering data. The acquisition order should specify the following: a. CID document number, revision, and CID PIN. b. Type required (see table I). c. Current-carrying material, if diff
20、erent (see 3.2.1). d. Binding post finish, if different (see 3.2.2). e. Solder terminal end finish, if different (see 3.2.2.1). f. Insulation material (see 3.2.3). g. Cap and insulated mounting washer color, if different (see 3.2.3). h. Non-turn feature, if different (see 3.4). i. Preservation, Pack
21、ing, and marking requirements (see 6.1). Type 1 = type I (see table I) AA59555 - X CID number Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59555A 5 7.4 Subject term (key word) listing. spring-loaded cap terminal board test set panels wiring te
22、rmination MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY: Custodians: Army - CR Navy - EC Air Force - 11 GSA - FSS Review Activity: Air Force - 99 Preparing Activity: DLA - GS2 (Project 5940-2006-004) NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
