1、DESC-DWG-8057 57 = 7777775 00178Lil 3 W LT R OLSCRIPTION DATE A PPROVE 0 Prepared in accordance with DOO-STO-100 Selected item drawing BEFEIIS ELEETROIICS tutru CNTER ORIGINAL DATE OF BAYTIN, 1110 RESISTOR, VOLTAGE DRAW I NG : 5 MAY 89 SENSITIVE (VARISTOR) , I PAQE 1 OF 6 I I oercrow 144 YAR 76 AMSC
2、 NIA - DISTRIBUTION STATEMENT A. A ved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DESC-DWG-BB057 59 W 9979495 0017842 5 W DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO 1. SCOPE 1.1 Scope, This draw
3、ing covers the requirements for voltage sensitive resistors (varistors) to be 1.2 Part number. The complete part number shall be as shown in the following example: ised for suppressing transients in electronic circuitry. A 14933 88057 REV PAGE 2 88057- I I I brawi ng number I I Dash number (see tabl
4、e I) 2, APPLICABLE DOCUMENTS 2.1 Government specification and standard, Unless otherwise specified, the following specification ind standard, of the issue listed in that issue of the Department of Defense Index of Specifications ind Standards specified in the solicitation, form a part of this drawin
5、g to the extent specified herein. SPECIFICATION MI L ITARY MIL-R-83530 - Resistor, Vol tage Sensi tive, Varistor, General Specification for. STANDARD MILITARY MI L-STD- 1285 - Marking of Electrical and Electronic Parts. (Copies of the specification and standard required by manufacturers in connectio
6、n with specific icquisition functions should be obtained from the contracting activity or as directed by the :ontracting activity. 1 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the *eferences cited herein (except for associated detall specifications, spec
7、ification sheets or MS ;tandardcl, the text of this drawing shall take precedence, Nothing in this drawing, however, shall ;upersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQJIREMENTS 3.1 Item requirements, The individual item requirements shall be in acc
8、ordance with MIL-R-83530, ind as specifled herein. 3.2 Design, construction, and physical dimensions. Design, construction, and physical dimensions 3.2.1 Design documentation. The design documentation shall be In accordance with MIL-R-83530 and ;hall be as specified in MIL-R-83530 and herein (see fi
9、gure 1). inless otherwise speclfied in the contract or purchase order, shall be retained by the manufacturer and ivallable for review by the acquiring activity or contractor upon request. I SIZE I CODE IDENT. NO. I DWG NO. I I I DESC FORM 144A APR 83 Provided by IHSNot for ResaleNo reproduction or n
10、etworking permitted without license from IHS-,-,-DESC-DWG-057 57 = 7777775 0037843 7 DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO A- r- r-c* SIZE CODE IDENT. NO. DWG NO. A 14933 88057 3 REV PAGE M DIA TYP LN DIA TYP ! Dimensions .tr I Inches I Millimeters I I I I I I A I 2.40 Max I 61 Max 6 1 1.60
11、 Max I 40.6 Max C I 1.75 t0.30 I 44.45 t0.75 O I 1.00 10.30 I 25.40 t0.75 E I 0.65 t0.30 I 16.5 t0.75 F I 0.12 t0.10 I 2.9 t0.20 G I 0.91 Max I 23.1 Max H I 1.60 Max I 40.6 Max J I 0.50 10.01 I 12.7 t0.25 K I 0.063 *0.0051 1.6 t0.13 L I 0.25 tO.01 I 6.35 10.25 M I 0.255 t0.0051 6.5 I0.13 N I 0.21 t0
12、.0051 5.45 t0.13 P I 1.60 10.04 I 40.6 11.0 I I NOTES : 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DESC-DWG-057 57 m 7477795 O039844 7 i- I SIZE CODE IDEN
13、T. NO. DWG NO. DEFENSE ELECTRONICS SUPPLY CENTER A 14933 88057 REV PAGE 4 DAYTON, OHIO 3.3 Electrical characteristics. 3.3.1 Power rating. The power rating for varistors shall be 1.5 watts. 33.2 Voltage rating. The voltage rating shall be as specified in table I. 33.3 Ener ratin , The energy rating
14、shall be as specified in table I. The test peak current 3.3.4 Peak current. The peak current shall be as specified in table I. 3.3.5 Clamping voltage. The clamping voltage shall be as specified in table I. 3.3.6 Capacitance. The capacitance shall be as specified in table I. 3.3.7 Voltage tolerance.
15、The voltage tolerance shall be as specified in table I. 3.3.8 Operating temperage range. The operating temperature range shall be -55C to +85C. 3.3.9 Storage temperature range, The storage temperature range shall be -55C to +125C. 3.4 Marking. Marking shall be in accordance with MIL-STD-1285, except
16、 the part number shall be in 3.5 Workmanship. Resistors shall be processed in such a manner as to be uniform in quality and 3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer 4. QUALITY ASSURANCE PROVISIONS shall be e accordance with 1.2 herein, with the
17、 manufacturers name or CAGE code, date code, and lot symbol. parts shall be free from any defects that will affect life, serviceability, or appearance. requesting to be listed as a suggested source of supply. 4.1 Qualification inspection. Qualification inspection is not applicable to this document.
18、4.2 Quality conformance inspection. 4.2.1 Inspection of product for delivery. Inspection of product for delivery shall consist of groups A and B inspections of MIL-R-83530 , except that peak current and energy tests shall not be required for group B, subgroup III. 4,3 Inspection of packaging, 5, PAC
19、KAGING 5.1 Packaging. The requirements for packaging shall be in accordance with MIL-R-83530. Inspection of packaging shall be in accordance with MIL-R-83530. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TABLE I. Rating and characteristics. I I I
20、I I 1 I I I Dash I Voltage I Energy I Peak I Nominal I Max clamping I Typical I I number I rating I (max) I current I varistor I voltage at I capacitance I I I (max) I (joules) I (amperes) I voltage I test current I (picofarads) I I I (rms dc) I I I (VI I (VI (I) I I I I I I I I I I I I I I I I I I
21、I O01 I 130 I 125 I 15000 I 200 +28 I 350 I 200 I 4700 I l I I I I -16 I I I I I I I I I I I I 002 I 150 1 145 I 15000 I 240 *28 I 410 I 200 I 4000 I I I I I I I I I I I I I I l I 1 390 +39 I 680 I 200 I 2500 I I 003 I 250 I 240 I I I I I I I 004 I 275 I 270 I 15000 I 430 143 I 750 I 200 I 2200 I I
22、I I I I I I I I I I I I I I I I 320 I 300 I 15000 I 510 +29 I 850 I 200 I 1900 I I I I I 1 I I I I I l I I I l5Ooo I -36 I I I I f Oo5 I I I I -48 I I I I I Oo6 I I I I -70 I I I I I Oo7 I I I I -80 I I I I I I I I l8O0O I -85 I I I I l l I I l8O0O I -105 I I I I 420 I 400 I 18000 I 680 +68 I 1200 I
23、 200 I 1500 I 480 I 450 I 18000 I 750 +74 I 1300 I 200 I 1300 I I I I I 820 +90 I 1440 I 200 I 1200 I I 008 I 510 500 I I I I I I 910 +95 I 1600 I 200 I 1100 I I O09 I 575 550 I I I I I I O10 I 660 I 600 I 18000 11050 *1101 1820 I 200 I 1000 I I I I I I I I I I I I I I I. I I I I O11 I 750 I 700 I 1
24、8000 11200 I1201 2050 I 200 I 800 I I I I I I I I I I SIZE CODE IDENT. NO. DEFENSE ELECTRONICS SUPPLY CENTER A 14933 DWG NO. 88057 I I I DESC FORM 144A APR a3 REV PAGE 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DESC-DWG-48057 59 9979995 00L78Y
25、b 2 W SIZE CODE IDENT. NO. DEFENSE ELECTRONICS SUPPLY CENTER A 14933 I DWG NO. 88057 6. NOTES 6.1 Intended use. These resistors are used in circuits where high current and high energy level are present. 6.2 Ordering data. The contract or purchase order shall specify the following: a. Complete part n
26、umber. b. Requirements for delivery, one copy of the quality conformance inspection data, or certificate of compliance that parts have passed quality conformance inspection with each shipment of parts by the manufacturer. 6.3 User of record. Coordination of this document, for future revisions, shall
27、 be coordinated only with the suggested source of supply and the users of record of this document. For requests to be a user of record, contact DESC-E, 1507 Wilmington Pike, Dayton, OH 45444-5278 or telephone (513)296-6004. 6.4 Suggested source of supply. A suggested source of supply is listed herei
28、n. Additional sources will be added as they become available. For assistance in the use of this drawing, contact DESC-ECP, 1507 Wilmington Pike, Dayton, OH 45444-5278, or telephone (513)296-6004. REV I I I DESC drawing I Vendor CAGE I number I number I I PAGE 6 I l 7 I I 88057-001 i 02735 I 88057-00
29、2 I 02735 I 88057-003 I 02735 I 88057-004 I 02735 I 88057-005 I 02735 I 88057-006 I 02735 I 88057-007 I 02735 i 88057-008 I 02735 I 88057-009 I 02735 I 88057-010 I 02735 I 88057-011 I 02735 I I Vendor similar I part number L/ I I V130HE150 I V150HE150 I V250HE250 I V275HE250 I V320HE300 I V420HE400
30、I V480HE450 I V510HE500 I V575HE550 I V660HE600 I V750HE700 i/ Caution. Do not use this part number for item - -tion, Items acquired to this number may not satisfy the performance requirements of this drawing. Vendor CAGE number 02735 Vendor name and address Marketing and sales: marris Corporation Semiconductor Section Route 202 Somervill e, NJ 08876-0591 Manufactured by: Harris Corporation - EECO Ltd. The Demesne Dundal k, County Louth Republic of Ireland 4- Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
