1、REVISIONS LTR DESCRIPTION DATE APPROVED A Clarify VSWR and IL testing requirements as engineering info. 2 February 2010 Abdonasser M. Abdouni Prepared in accordance with ASME Y14.100 Source Control Drawing REV PAGE REV STATUS OF PAGES REV A A A A A A PAGE 1 2 3 4 5 6 PMIC N/A PREPARED BY DEFENSE SUP
2、PLY CENTER, COLUMBUS COLUMBUS, OHIO 43218-3990 Ron Gary Original date of drawing 7 May 2001 CHECKED BY TITLE Lee Surowiec CONNECTOR, PLUG, ELECTRICAL, RF, SERIES BNC, RIGHT ANGLE, 75 OHMS, FOR LOW SMOKE CABLES APPROVED BY Robert Heber SIZE CAGE CODE DWG. NO. 01025 A 037Z3 REV A PAGE 1 OF 6 AMSC N/A
3、5935-E817-003Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZECAGE CODE DWG NO. A 037Z3 01025 REV A PAGE 2 NOTES: 1. Dimensions are in inches. Metric equivalents are in parenthesis. 2. Metric
4、 equivalents are given for reference purposes only. 3. All undimensioned pictorial configurations are for reference purposes only. 4. No safety wire holes are required. 5. Series BNC, pin contact interface, 75, in accordance with figure 2. FIGURE 1. General configuration. Provided by IHSNot for Resa
5、leNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZECAGE CODE DWG NO. A 037Z3 01025 REV A PAGE 3 FIGURE 2. Interface, series BNC, pin contact, 75. Provided by IHSNot for ResaleNo reproduction or networking permitted witho
6、ut license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZECAGE CODE DWG NO. A 037Z3 01025 REV A PAGE 4 Dim Ltr Dimensions in inches with metric equivalents (mm) in parentheses Minimum MaximumA .385 (9.78) .390 (9.91) B Gauge test D .052 (1.32) .054 (1.37) E .210 (5.33) .230
7、 (5.84) G .091 (2.31) .097 (2.46) H .463 (11.76) .473 (12.01) H * .394 (10.01) .400 (10.16) J .124 (3.15) K .091 (2.31) .097 (2.46) L .003 (0.08) M .018 (0.46) .022 (0.56) N .025 (0.64)P .208 (5.28) .228 (5.79) Q .078 (1.98) R .052 (1.32) .087 (2.21) T .045 (1.14) .049 (1.24) U .180 (4.57) .184 (4.6
8、7) NOTES: 1. Dimensions are in inches. Metric equivalents are in parenthesis. 2. Metric equivalents are given for general information only. 3. In the mated condition, the longitudinal force of the spring of the coupling mechanism shall exceed the pressure exerted by the sealing gasket by an amount.
9、4. This interface shall meet the gauge requirements as specified necessary to insure butting of the outer contacts at the reference plane. 5. This dimension applies only if R dimension is not the same as D dimension. FIGURE 2. Interface, series BNC, pin contact, 75 - Continued. Provided by IHSNot fo
10、r ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZECAGE CODE DWG NO. A 037Z3 01025 REV A PAGE 5 ENGINEERING DATA: This document covers the requirements for radio frequency connectors accommodating special low smoke
11、 coaxial cables. Frequency range: 0-2.5 GHz. VSWR: 1.35 :1, maximum. Insertion loss: .25 dB at 2 GHz. REQUIREMENTS: These connectors shall conform to all the requirements of the latest issue of DSCC drawing 84148, figures 1 and 2 herein, and MIL-PRF-39012/20, and accommodate the cables listed in tab
12、le I, with the following additions and exceptions. Electrical: Shall be in accordance with MIL-PRF-39012/20. Impedance: 75. Mechanical: Shall be in accordance with MIL-PRF-39012/20 with the following exception: Interface to be in accordance with figure 2. No safety wire holes are required. Environme
13、ntal: Shall be in accordance with MIL-PRF-39012/20. TABLE I. Cable accommodation. Part or Identifying Number (PIN) 1/ 2/ Applicable cable 01025BBSA M17/229-00001 1/ These connectors have captivated center contacts. 2/ These connectors are assembled using the MIL-C-22520/5 crimp tool and using the fo
14、llowing crimp dies: M22520/5-19 Closure A. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZECAGE CODE DWG NO. A 037Z3 01025 REV A PAGE 6 Approved sources of supply. Approved sources of supply
15、 are listed herein. Additional sources will be added as they become available. The vendors listed below have agreed to this drawing and a certificate of compliance has been submitted to DSCC-VAI. DSCC drawing PIN Vendor CAGE number Vendor similar PIN 1/ 01025BBSA 00795 3190-884 1/ Parts must be purchased to this DSCC PIN to assure that all performance requirements and test are met. Vendor CAGE Vendor name Number and address 00795 Delta Electronics 416 Cabot Street Beverly, MA 01915 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
